A Novel Nonlinear Mason Model And Nonlinear Distortion Characterization For Surface Acoustic Wave Duplexers

Surface acoustic wave (SAW) technology has been in use for well over one century. In the last few decades, due to its low cost and high performance, this technology has been widely adopted in modern wireless communication systems, to build filtering devices at radio frequency (RF). SAW filters and duplexers can be virtually found inside every mobile handset. SAW devices are traditionally recognized as passive devices with high linear signal processing behavior. However, recent deployments of third generation (3G) and fourth generation (4G) mobile networks require the handsets to handle an increasing number of frequency bands with more complex modulation /demodulation schemes and higher data rate for more subscribers. These requirements directly demand more stringent linearity specifications on the front end devices, including the SAW duplexers. In the past, SAW duplexer design was based on empirically obtained design rules to meet the linearity specifications. Lack of predictability and an understanding of the root cause of the nonlinearity have limited the potential applications of SAW duplexers. Therefore, research on the nonlinearity characterization and an accurate modeling of SAW nonlinearity for mobile device applications are very much needed. The Ph.D. work presented here primarily focuses on developing a general nonlinear model for SAW resonators/duplexers. Their nonlinear characteristics were investigated by measuring the harmonic and intermodulation distortions of resonators. A nonlinear Mason model is developed and the characterization results are integrated into SAW duplexer design flows to help to simulate the nonlinear effects accurately and improve the linearity performance of the products. iv In this dissertation, first, a novel nonlinear Mason equivalent circuit model including a third order nonlinear coefficient in the wave propagation is presented. Next, the nonlinear distortions of SAW resonators are analyzed by measuring large-signal harmonic and intermodulation spurious emission on resonators using a wafer probe station. The influence of the setups on the measurement reliability and reproducibility is discussed. Further, the nonlinear Mason model is validated by comparing its simulation results with harmonic and intermodulation measurements on SAW resonators and a WCDMA Band 5 duplexer. The Mason model developed and presented here is the first and only nonlinear physical model for SAW devices based on the equivalent circuit approach. By using this new model, good simulation measurement agreements are obtained on both harmonic and intermodulation distortions for SAW resonators and duplexers. These outcomes demonstrate the validity of the research on both the characterization and modeling of SAW devices. The result obtained confirms that the assumption of the representation of the 3 rd order nonlinearity in the propagation by a single coefficient is vali

Nonlinear mechanisms in passive microwave devices

Premi extraordinari doctorat curs 2010-2011, àmbit d’Enginyeria de les TICThe telecommunications industry follows a tendency towards smaller devices, higher power and higher frequency, which imply an increase on the complexity of the electronics involved. Moreover, there is a need for extended capabilities like frequency tunable devices, ultra-low losses or high power handling, which make use of advanced materials for these purposes. In addition, increasingly demanding communication standards and regulations push the limits of the acceptable performance degrading indicators. This is the case of nonlinearities, whose effects, like increased Adjacent Channel Power Ratio (ACPR), harmonics, or intermodulation distortion among others, are being included in the performance requirements, as maximum tolerable levels. In this context, proper modeling of the devices at the design stage is of crucial importance in predicting not only the device performance but also the global system indicators and to make sure that the requirements are fulfilled. In accordance with that, this work proposes the necessary steps for circuit models implementation of different passive microwave devices, from the linear and nonlinear measurements to the simulations to validate them. Bulk acoustic wave resonators and transmission lines made of high temperature superconductors, ferroelectrics or regular metals and dielectrics are the subject of this work. Both phenomenological and physical approaches are considered and circuit models are proposed and compared with measurements. The nonlinear observables, being harmonics, intermodulation distortion, and saturation or detuning, are properly related to the material properties that originate them. The obtained models can be used in circuit simulators to predict the performance of these microwave devices under complex modulated signals, or even be used to predict their performance when integrated into more complex systems. A key step to achieve this goal is an accurate characterization of materials and devices, which is faced by making use of advanced measurement techniques. Therefore, considerations on special measurement setups are being made along this thesis.Award-winningPostprint (published version

Piezo-electromechanical smart materials with distributed arrays of piezoelectric transducers: Current and upcoming applications

This review paper intends to gather and organize a series of works which discuss the possibility of exploiting the mechanical properties of distributed arrays of piezoelectric transducers. The concept can be described as follows: on every structural member one can uniformly distribute an array of piezoelectric transducers whose electric terminals are to be connected to a suitably optimized electric waveguide. If the aim of such a modification is identified to be the suppression of mechanical vibrations then the optimal electric waveguide is identified to be the 'electric analog' of the considered structural member. The obtained electromechanical systems were called PEM (PiezoElectroMechanical) structures. The authors especially focus on the role played by Lagrange methods in the design of these analog circuits and in the study of PEM structures and we suggest some possible research developments in the conception of new devices, in their study and in their technological application. Other potential uses of PEMs, such as Structural Health Monitoring and Energy Harvesting, are described as well. PEM structures can be regarded as a particular kind of smart materials, i.e. materials especially designed and engineered to show a specific andwell-defined response to external excitations: for this reason, the authors try to find connection between PEM beams and plates and some micromorphic materials whose properties as carriers of waves have been studied recently. Finally, this paper aims to establish some links among some concepts which are used in different cultural groups, as smart structure, metamaterial and functional structural modifications, showing how appropriate would be to avoid the use of different names for similar concepts. © 2015 - IOS Press and the authors