Design and Analysis of Robust Low Voltage Static Random Access Memories.

Static Random Access Memory (SRAM) is an indispensable part of most modern VLSI designs and dominates silicon area in many applications. In scaled technologies, maintaining high SRAM yield becomes more challenging since they are particularly vulnerable to process variations due to 1) the minimum sized devices used in SRAM bitcells and 2) the large array sizes. At the same time, low power design is a key focus throughout the semiconductor industry. Since low voltage operation is one of the most effective ways to reduce power consumption due to its quadratic relationship to energy savings, lowering the minimum operating voltage (Vmin) of SRAM has gained significant interest. This thesis presents four different approaches to design and analyze robust low voltage SRAM: SRAM analysis method improvement, SRAM bitcell development, SRAM peripheral optimization, and advance device selection. We first describe a novel yield estimation method for bit-interleaved voltage-scaled 8-T SRAMs. Instead of the traditional trade-off between write and read, the trade-off between write and half select disturb is analyzed. In addition, this analysis proposes a method to find an appropriate Write Word-Line (WWL) pulse width to maximize yield. Second, low leakage 10-T SRAM with speed compensation scheme is proposed. During sleep mode of a sensor application, SRAM retaining data cannot be shut down so it is important to minimize leakage in SRAM. This work adopts several leakage reduction techniques while compensating performance. Third, adaptive write architecture for low voltage 8-T SRAMs is proposed. By adaptively modulating WWL width and voltage level, it is possible to achieve low power consumption while maintaining high yield without excessive performance degradation. Finally, low power circuit design based on heterojunction tunneling transistors (HETTs) is discussed. HETTs have a steep subthreshold swing beneficial for low voltage operation. Device modeling and design of logic and SRAM are proposed.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91569/1/daeyeonk_1.pd

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V

Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien

Simulation of FinFET Structures

The intensive downscaling of MOS transistors has been the major driving force behind the aggressive increases in transistor density and performance, leading to more chip functionality at higher speeds. While on the other side the reduction in MOSFET dimensions leads to the close proximity between source and drain, which in turn reduces the ability of the gate electrode to control the potential distribution and current flow in the channel region and also results in some undesirable effects called the short-channel effects. These limitations associated with downscaling of MOSFET device geometries have lead device designers and researchers to number of innovative techniques which include the use of different device structures, different channel materials, different gate-oxide materials, different processes such as shallow trench isolation, source/drain silicidation, lightly doped extensions etc. to enable controlled device scaling to smaller dimensions. A lot of research and development works have been done in these and related fields and more remains to be carried out in order to exploit these devices for the wider applications

Threshold Voltage Tuning for Faster Activation With Lower Noise in Tri-Mode MTCMOS Circuits

A new threshold voltage tuning methodology is explored in this paper to minimize the peak power/ground bouncing noise with smaller sleep transistors in multi-threshold CMOS (MTCMOS) circuits. Different circuit techniques with the threshold voltage tuning strategy lower the activation noise, the activation delay, and the size of the additional sleep transistors by up to 27.76%, 32.66%, and 85.71%, respectively, as compared to a previously published noise-aware MTCMOS circuit with standard zero-body-biased high threshold voltage sleep transistors in a UMC 80-nm CMOS technology