Measurement of permeability for ferrous metallic plates using a novel lift-off compensation technique on phase signature

Lift-off of sensor affects the prediction of electromagnetic properties for both ferrous and non-ferrous steel plates. In this paper, we developed a strategy to address this issue for ferrous plates. With increased lift-off, the phase of the measured impedance for steel plates reduces. Meanwhile, the magnitude of the impedance signal decreases. Based on these facts, a phase compensation algorithm is developed which corrects the phase change due to lift-off considering the magnitude of the impedance signal. Further, a new magnetic permeability prediction technique is presented, which has been validated by analytical and measured results. With this new technique, the error in permeability prediction is less than 2% within the range of lift-offs tested

An Eddy-Current Testing Method for Measuring the Thickness of Metallic Plates

Thickness measurements of metallic plates are mandatory in many industrial scenarios. Methods based on eddy-current testing (ECT) are ideal for fast and accurate online contactless thickness measurements, making them very attractive in the Industry 4.0 scenario. This contribution is focused on a specific and robust ECT technique proposed in the past by the scientific community. The main limitation is its applicability to thin materials only, where the thickness of the material is much smaller than the overall size of the ECT probe. Extending the range of applicability to thicker materials introduces a progressive and severe degradation of the measurement accuracy. In this article, we analyze the theoretical foundation of this method with an entirely original approach based on the celebrated Buckingham π theorem. In doing this, we draw the complete theoretical picture of the method, providing a simple, clear, and rigorous view of its performance and intrinsic limitations. Moreover, we propose two solutions, one analytical and the other iterative, to accurately estimate the thickness of the materials from thin to thick values. Finally, a numerical analysis combined with an experimental campaign confirms the effectiveness of the proposed solutions, making the method suitable for industrial and other applications

Analysis of Tilt Effect on Notch Depth Profiling Using Thin-Skin Regime of Driver-Pickup Eddy-Current Sensor

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter–receiver (T-R) sensor is designed with a small mean radius of 1 mm. In addition, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution, with a limit of 0.2 μm and selected as 0.25 mm. Experiments were conducted for imaging of an aluminium sheet with seven machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10% for tilt angles up to 60 degrees

Passive low frequency RFID for non-destructive evaluation and monitoring

Ph. D ThesisDespite of immense research over the years, defect monitoring in harsh environmental conditions still presents notable challenges for Non-Destructive Testing and Evaluation (NDT&E) and Structural Health Monitoring (SHM). One of the substantial challenges is the inaccessibility to the metal surface due to the large stand-off distance caused by the insulation layer. The hidden nature of corrosion and defect under thick insulation in harsh environmental conditions may result in it being not noticed and ultimately leading to failures. Generally electromagnetic NDT&E techniques which are used in pipeline industries require the removal of the insulation layer or high powered expensive equipment. Along with these, other limitations in the existing techniques create opportunities for novel systems to solve the challenges caused by Corrosion under Insulation (CUI). Extending from Pulsed Eddy Current (PEC), this research proposes the development and use of passive Low Frequency (LF) RFID hardware system for the detection and monitoring of corrosion and cracks on both ferrous and non-ferrous materials at varying high temperature conditions. The passive, low cost essence of RFID makes it an enchanting technique for long term condition monitoring. The contribution of the research work can be summarised as follows: (1) implementation of novel LF RFID sensor systems and the rig platform, experimental studies validating the detection capabilities of corrosion progression samples using transient feature analysis with respect to permeability and electrical conductivity changes along with enhanced sensitivity demonstration using ferrite sheet attached to the tag; (2) defect detection using swept frequency method to study the multiple frequency behaviour and further temperature suppression using feature fusion technique; (3) inhomogeneity study on ferrous materials at varying temperature and demonstration of the potential of the RFID system; (4) use of RFID tag with ceramic filled Poly-tetra-fluoro-ethyulene (PTFE) substrate for larger applicability of the sensing system in the industry; (5) lift-off independent defect monitoring using passive sweep frequency RFID sensors and feature extraction and fusion for robustness improvement. This research concludes that passive LF RFID system can be used to detect corrosion and crack on both ferrous and non-ferrous materials and then the system can be used to compensate for temperature variation making it useful for a wider range of applications. However, significant challenges such as permanent deployment of the tags for long term monitoring at higher temperatures and much higher standoff distance, still require improvement for real-world applicability.Engineering and Physical Sciences Research Council (EPSRC) CASE, National Nuclear Laboratory (NNL)