Piin läpivientien luotettavuus ja elinikä termisessä rasituksessa

Through-silicon via (TSV) is one of the key technologies for three-dimensional (3D) integrated circuits (ICs). TSVs enable vertical electrical connections between components which greatly reduces interconnection lengths. Regardless of all the promise the technique has shown, there are still major obstacles surrounding reliability and the cost of fabrication of the TSV structure. The first part of the thesis is a literature survey that focuses on different failure mechanisms of TSVs. In addition, different fabrication and design choices of TSVs are presented with the focus being on their effect on reliability. The experimental part of the thesis presents reliability and lifetime assessment of tapered partially copper-filled blind TSVs under thermal cycling. The reliability test was carried out with nine samples. Six of them had 420 vias and three of them had 1400 vias in a daisy chain structure. Finite element method (FEM) was used to predict the critical failure locations of the TSV structure. Lifetime was predicted by Weibull analysis. The cross-sections of the test samples were prepared by molding, mechanical grinding and polishing and analyzed by scanning electron microscope (SEM). Electrical measurements showed almost constant resistance increase in the samples before failures were noticed. The first failed sample was noticed after 200 cycles and the last at 4000 cycles. Lifetime of TSVs under thermal cycling was proven to be acceptable with used failure criterion. According to Weibull analysis, about 10 % of the samples with 420 vias will break after 1000 cycles. Sample preparation for imaging was deemed sufficient although the grinding caused artifacts. The simulation results were compared with SEM micrographs. The images showed that the failures were located at the maximum stress areas, identified with FEM simulations, at the bottom of the via. From the SEM images, it was deduced that the defects initiated from the fabrication process and propagated due to maximum localized stress.Piin läpivienti -rakenteet ovat keskeisessä osassa kolmiulotteisten integroitujen piirien kehityksessä. Piin läpiviennit mahdollistavat komponenttien vertikaalin yhdistämisen toisiinsa, mikä lyhentää huomattavasti niiden välistä etäisyyttä. Kaikista hyvistä puolista huolimatta tekniikalla on vielä haasteita edessään. Niistä suurimmat liittyvät rakenteen luotettavuuteen ja valmistuskustannuksiin. Diplomityön kirjallisessa osuudessa keskitytään piin läpivientien erilaisiin vauriomekanismeihin. Sen lisäksi tutkitaan valmistus- ja suunnitteluratkaisujen vaikutusta läpivientien luotettavuuteen. Kokeellisen osan tarkoituksena on osittain kuparitäytettyjen kaventuvien piin läpivientien luotettavuuden ja eliniän määrittäminen termisessä syklaustestissä. Luotettavuustestaus suoritettiin yhdeksällä näytteellä, joista kuudessa oli 420 läpivientiä ja kolmessa 1400 läpivientiä ketjurakenteessa. Elementtimallintamisen avulla määritettiin kriittiset vauriokohdat läpivientirakenteessa ja elinikä määritettiin Weibull-analyysillä. Näytteiden poikkileikkauksien valmistamiseen käytettiin muovaamista, mekaanista hiomista ja kiillotusta ja analysointi suoritettiin pyyhkäisyelektronimikroskoopilla. Näytteiden resistanssi nousi tasaisesti ennen rikkoutumisten havaitsemista. Ensimmäinen rikkoutuminen huomattiin 200 syklin jälkeen ja viimeinen 4000 syklin kohdalla. Näytteiden luotettavuus osoittautui hyväksi käytetyillä kriteereillä. Weibull-analyysin mukaan 10 % 420 läpiviennin näytteistä rikkoutuu 1000 syklin jälkeen. Karkea arvio voidaan tehdä, että satunnainen läpivienti rikkoutuu 0,024 % todennäköisyydellä 1000 syklin jälkeen. Pyyhkäisyelektronimikroskoopin kuvien perusteella havaittiin, että näytteet rikkoutuivat maksimaalisen rasituksen alueella läpivientien alaosassa. Kuvien perusteella päädyttiin johtopäätökseen, että näytteiden rikkoutumisen aiheuttivat virheet, jotka ovat peräisin valmistusprosessista ja jotka etenivät rakenteessa termisen rasituksen vaikutuksesta

Through-Silicon Vias in SiGe BiCMOS and Interposer Technologies for Sub-THz Applications

Im Rahmen der vorliegenden Dissertation zum Thema „Through-Silicon Vias in SiGe BiCMOS and Interposer Technologies for Sub-THz Applications“ wurde auf Basis einer 130 nm SiGe BiCMOS Technologie ein Through-Silicon Via (TSV) Technologiemodul zur Herstellung elektrischer Durchkontaktierungen für die Anwendung im Millimeterwellen und Sub-THz Frequenzbereich entwickelt. TSVs wurden mittels elektromagnetischer Simulationen modelliert und in Bezug auf ihre elektrischen Eigenschaften bis in den sub-THz Bereich bis zu 300 GHz optimiert. Es wurden die Wechselwirkungen zwischen Modellierung, Fertigungstechnologie und den elektrischen Eigenschaften untersucht. Besonderes Augenmerk wurde auf die technologischen Einflussfaktoren gelegt. Daraus schlussfolgernd wurde das TSV Technologiemodul entwickelt und in eine SiGe BiCMOS Technologie integriert. Hierzu wurde eine Via-Middle Integration gewählt, welche eine Freilegung der TSVs von der Wafer Rückseite erfordert. Durch die geringe Waferdicke von ca. 75 μm wird einen Carrier Wafer Handling Prozess verwendet. Dieser Prozess wurde unter der Randbedingung entwickelt, dass eine nachfolgende Bearbeitung der Wafer innerhalb der BiCMOS Pilotlinie erfolgen kann. Die Rückseitenbearbeitung zielt darauf ab, einen Redistribution Layer auf der Rückseite der BiCMOS Wafer zu realisieren. Hierzu wurde ein Prozess entwickelt, um gleichzeitig verschiedene TSV Strukturen mit variablen Geometrien zu realisieren und damit eine hohe TSV Design Flexibilität zu gewährleisten. Die TSV Strukturen wurden von DC bis über 300 GHz charakterisiert und die elektrischen Eigenschaften extrahiert. Dabei wurde gezeigt, dass TSV Verbindungen mit sehr geringer Dämpfung <1 dB bis 300 GHz realisierbar sind und somit ausgezeichnete Hochfrequenzeigenschaften aufweisen. Zuletzt wurden vielfältige Anwendungen wie das Grounding von Hochfrequenzschaltkreisen, Interposer mit Waveguides und 300 GHz Antennen dargestellt. Das Potential für Millimeterwellen Packaging und 3D Integration wurde evaluiert. TSV Technologien sind heutzutage in vielen Anwendungen z.B. im Bereich der Systemintegration von Digitalschaltkreisen und der Spannungsversorgung von integrierten Schaltkreisen etabliert. Im Rahmen dieser Arbeit wurde der Einsatz von TSVs für Millimeterwellen und dem sub-THz Frequenzbereich untersucht und die Anwendung für den sub-THz Bereich bis 300 GHz demonstriert. Dadurch werden neue Möglichkeiten der Systemintegration und des Packaging von Höchstfrequenzsystemen geschaffen.:Bibliographische Beschreibung List of symbols and abbreviations Acknowledgement 1. Introduction 2. FEM Modeling of BiCMOS & Interposer Through-Silicon Vias 3. Fabrication of BiCMOS & Silicon Interposer with TSVs 4. Characterization of BiCMOS Embedded Through-Silicon Vias 5. Applications 6. Conclusion and Future Work 7. Appendix 8. Publications & Patents 9. Bibliography 10. List of Figures and Table

High Speed Test Interface Module Using MEMS Technology

With the transient frequency of available CMOS technologies exceeding hundreds of gigahertz and the increasing complexity of Integrated Circuit (IC) designs, it is now apparent that the architecture of current testers needs to be greatly improved to keep up with the formidable challenges ahead. Test requirements for modern integrated circuits are becoming more stringent, complex and costly. These requirements include an increasing number of test channels, higher test-speeds and enhanced measurement accuracy and resolution. In a conventional test configuration, the signal path from Automatic Test Equipment (ATE) to the Device-Under-Test (DUT) includes long traces of wires. At frequencies above a few gigahertz, testing integrated circuits becomes a challenging task. The effects on transmission lines become critical requiring impedance matching to minimize signal reflection. AC resistance due to the skin effect and electromagnetic coupling caused by radiation can also become important factors affecting the test results. In the design of a Device Interface Board (DIB), the greater the physical separation of the DUT and the ATE pin electronics, the greater the distortion and signal degradation. In this work, a new Test Interface Module (TIM) based on MEMS technology is proposed to reduce the distance between the tester and device-under-test by orders of magnitude. The proposed solution increases the bandwidth of test channels and reduces the undesired effects of transmission lines on the test results. The MEMS test interface includes a fixed socket and a removable socket. The removable socket incorporates MEMS contact springs to provide temporary with the DUT pads and the fixed socket contains a bed of micro-pins to establish electrical connections with the ATE pin electronics. The MEMS based contact springs have been modified to implement a high-density wafer level test probes for Through Silicon Vias (TSVs) in three dimensional integrated circuits (3D-IC). Prototypes have been fabricated using Silicon On Insulator SOI wafer. Experimental results indicate that the proposed architectures can operate up to 50 GHz without much loss or distortion. The MEMS probes can also maintain a good elastic performance without any damage or deformation in the test phase

Self-Aligned 3D Chip Integration Technology and Through-Silicon Serial Data Transmission

The emerging three-dimensional (3D) integration technology is expected to lead to an industry paradigm shift due to its tremendous benefits. Intense research activities are going on about technology, simulation, design, and product prototypes. This thesis work aims at fabricating through-silicon vias (TSVs) on diced processor chips, and later bonding them into a 3D-stacked chip. How to handle and process delicate processor chips with high alignment precision is a key issue. The TSV process to be developed also needs to adapt to this constraint. Four TSV processes have been studied. Among them, the ring-trench TSV process demonstrates the feasibility of fabricating TSVs with the prevailing dimensions, and the whole-through TSV process achieves the first dummy chip post-processed with TSVs in EPFL although the dimension is rather large to keep a reasonable aspect ratio (AR). Four self-alignment (SA) techniques have been investigated, among which the gravitational SA and the hydrophobic SA are found to be quite promising. Using gravitational SA, we come to the conclusion that cavities in silicon carrier wafer with a profile angle of 60° can align the chips with less than 20 µm inaccuracies. The alignment precision can be improved after adopting more advanced dicing tools instead of using the traditional dicing saws and larger cavity profile angle. Such inaccuracy will be sufficient to align the relatively large TSVs for general products such as 3D image sensors. By fabricating bottom TSVs in the carrier wafer, a 3D silicon interposer idea has been proposed to stack another chip, e.g. a processor chip, on the other side of the carrier wafer. But stacking microprocessor chips fabricated with TSVs will require higher alignment precision. A hydrophobic SA technique using the surface tension force generated by the water-to-air interfaces around the pads can greatly reduce the alignment inaccuracy to less than 1 µm. This low-cost and high throughput SA procedure is processed in air, fully-compatible with current fabrication technologies, and highly stable and repeatable. We present a theoretical meniscus model to predict SA results and to provide the design rules. This technique is quite promising for advanced 3D applications involving logic and heterogeneous stacking. As TSVs' dimensions in the chip-level 3D integration are constrained by the chip-level processes, such as bonding, the smallest TSVs might still be about 5 µm. Thus, the area occupied by the TSVs cannot be neglected. Fortunately, TSVs can withstand very high bandwidths, meaning that data can be serialized and transmitted using less numbers of TSVs. With 20 µm TSVs, the 2-Gb/s 8:1 serial link implemented saves 75% of the area of its 8-bit parallel counterpart. The quasi-serial link proposed can effectively balance the inter-layer bandwidth and the serial links' area consumption. The area model of the serial or quasi-serial links working under higher frequencies provides some guidelines to choose the proper serial link design, and it also predicts that when TSV diameter shrinks to 5 µm, it will be difficult to keep this area benefit if without some novel circuit design techniques. As the serial links can be implemented with less area, the bandwidth per unit area is increased. Two scenarios are studied, single-port memory access and multi-port memory access. The expanded inter-layer bandwidth by serialization does not improve the system performance because of the bus-bottleneck problem. In the latter scenario, the inter-layer ultra-wide bandwidth can be exploited as each memory bank can be accessed randomly through the NoC. Thus further widening the inter-layer bandwidth through serialization, the system performance will be improved

Study of the impact of lithography techniques and the current fabrication processes on the design rules of tridimensional fabrication technologies

Working for the photolithography tool manufacturer leader sometimes gives me the impression of how complex and specific is the sector I am working on. This master thesis topic came with the goal of getting the overall picture of the state-of-the-art: stepping out and trying to get a helicopter view usually helps to understand where a process is in the productive chain, or what other firms and markets are doing to continue improvingUniversidad de sevilla.Máster Universitario en Microelectrónica: Diseño y Aplicaciones de Sistemas Micro/Nanométrico

Tunable Copper Microstructures in Blanket Films and Trenches Using Pulsed Electrodeposition

Copper interconnects in microelectronics have long been plagued with thermo-mechanical reliability issues. Control over the copper deposition process and resulting microstructure can dictate its material properties and reduce stresses as well as defects that form in the copper. In this thesis, pulse electrodeposition processing parameters were evaluated for their impact on the copper microstructure (grain size, texture, and twin density and stress state) through electron backscattering diffraction and wafer curvature measurements. Varying levels of constraint were also investigated for their effect on the copper microstructure to better understand the microstructures of more complex three-dimensional interconnects. Highly texture blanket copper films were deposited with various pulse frequencies and duty cycle, which was found to control grain size, orientation, and twin density. Higher twin densities were also observed in the films with lower residual stress. The findings from blanket film studies were carried over to trench deposited samples, where the influence of organic additives, typically used in the electrolytic bath to produce defect-free filling of advanced geometries, on the copper microstructure was studied. With the addition of organic additives, depositions produced finer grained structures with an increased contribution from the microstructure of the trench sidewall seed layer, especially with increasing trench aspect ratio. In addition, the increased constraint of the copper, resulted in larger stresses within the features and higher twin densities. The core of this dissertation demonstrated the ability to alter the resulting Cu microstructure through variations in pulse electrodeposition parameters

異種ダイレット積層を用いたフレキシブルハイブリッドデバイスの集積技術に関する研究

Tohoku University福島誉史課

3D modeling and integration of current and future interconnect technologies

Title from PDF of title page viewed June 21, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (pages 133-138)Thesis (Ph.D.)--School of Computing and Engineering and Department of Physics and Astronomy. University of Missouri--Kansas City, 2021To ensure maximum circuit reliability it is very important to estimate the circuit performance and signal integrity in the circuit design phase. A full phase simulation for performance estimation of a large-scale circuit not only require a massive computational resource but also need a lot of time to produce acceptable results. The estimation of performance/signal integrity of sub-nanometer circuits mostly depends on the interconnect capacitance. So, an accurate model for interconnect capacitance can be used in the circuit CAD (computer-aided design) tools for circuit performance estimation before circuit fabrication which reduces the computational resource requirement as well as the time constraints. We propose a new capacitance models for interconnect lines in multilevel interconnect structures by geometrically modeling the electrical flux lines of the interconnect lines. Closed-form equations have been derived analytically for ground and coupling capacitance. First, the capacitance model for a single line is developed, and then the new model is used to derive expressions for the capacitance of a line surrounded by neighboring lines in the same and the adjacent layers above and below. These expressions are simple, and the calculated results are within 10% of Ansys Q3D extracted values. Through silicon via (TSV) is one of the key components of the emerging 3D ICs. However, increasing number of TSVs in smaller silicon area leads to some severe negative impacts on the performance of the 3D IC. Growing signal integrity issues in TSVs is one of the major challenges of 3D integration. In this paper, different materials for the cores of the vias and the interposers are investigated to find the best possible combination that can reduce crosstalk and other losses like return loss and insertion loss in the TSVs. We have explored glass and silicon as interposer materials. The simulation results indicate that glass is the best option as interposer material although silicon interposer has some distinct advantages. For via cores three materials - copper (Cu), tungsten (W) and Cu-W bimetal are considered. From the analysis it can concluded that W would be better for high frequency applications due to lower transmission coefficient. Cu offers higher conductivity, but it has larger thermal expansion coefficient mismatch with silicon. The performance of Cu-W bimetal via would be in between Cu and W. However, W has a thermal expansion coefficient close to silicon. Therefore, bimetal Cu-W based TSV with W as the outer layer would be a suitable option for high frequency 3D IC. Here, we performed the analysis in terms of return loss, transmission coefficient and crosstalk in the vias. Signal speed in current digital systems depends mainly on the delay of interconnects. To overcome this delay problem and keep up with Moore’s law, 3D integrated circuit (vertical integration of multiple dies) with through-silicon via (TSV) has been introduced to ensure much smaller interconnect lengths, and lower delay and power consumption compared to conventional 2D IC technology. Like 2D circuit, the estimation of 3D circuit performance depends on different electrical parameters (capacitance, resistance, inductance) of the TSV. So, accurate modeling of the electrical parameters of the TSV is essential for the design and analysis of 3D ICs. We propose a set of new models to estimate the capacitance, resistance, and inductance of a Cu-filled TSV. The proposed analytical models are derived from the physical shape and the size of the TSV. The modeling approach is comprehensive and includes both the cylindrical and tapered TSVs as well as the bumps. On-chip integration of inductors has always been very challenging. However, for sub- 14nm on-chip applications, large area overhead imposed by the on-chip capacitors and inductors has become a more severe concern. To overcome this issue and ensure power integrity, a novel 3D Through-Silicon-Via (TSV) based inductor design is presented. The proposed TSV based inductor has the potential to achieve both high density and high performance. A new design of a Voltage Controlled Oscillator (VCO) utilizing the TSV based inductor is also presented. The implementation of the VCO is intended to study the feasibility, performance, and real-world application of the proposed TSV based inductor.Introduction -- Background of capacitance modeling of on-chip interconnect -- Accurate modeling of interconnect capacitance in multilevel interconnect structures for sub 22nm technology -- Analysis of different materials and structures for through silicon via and through glass via in 3D integrated circuits -- Impacts of different shapes of through-silicon-via core on 3D IC performance -- Accurate electrical modeling of cu-filled through-silicon-via (TSV) -- Design and characterize TSV based inductor for high frequency voltage-controlled oscillator design -- Conclusion and future wor

Signaling in 3-D integrated circuits, benefits and challenges

Three-dimensional (3-D) or vertical integration is a design and packaging paradigm that can mitigate many of the increasing challenges related to the design of modern integrated systems. 3-D circuits have recently been at the spotlight, since these circuits provide a potent approach to enhance the performance and integrate diverse functions within amulti-plane stack. Clock networks consume a great portion of the power dissipated in a circuit. Therefore, designing a low-power clock network in synchronous circuits is an important task. This requirement is stricter for 3-D circuits due to the increased power densities. Synchronization issues can be more challenging for 3-D circuits since a clock path can spread across several planes with different physical and electrical characteristics. Consequently, designing low power clock networks for 3-D circuits is an important issue. Resonant clock networks are considered efficient low-power alternatives to conventional clock distribution schemes. These networks utilize additional inductive circuits to reduce power while delivering a full swing clock signal to the sink nodes. In this research, a design method to apply resonant clocking to synthesized clock trees is proposed. Manufacturing processes for 3-D circuits include some additional steps as compared to standard CMOS processes which makes 3-D circuits more susceptible to manufacturing defects and lowers the overall yield of the bonded 3-D stack. Testing is another complicated task for 3-D ICs, where pre-bond test is a prerequisite. Pre-bond testability, in turn, presents new challenges to 3-D clock network design primarily due to the incomplete clock distribution networks prior to the bonding of the planes. A design methodology of resonant 3-D clock networks that support wireless pre-bond testing is introduced. To efficiently address this issue, inductive links are exploited to wirelessly transmit the clock signal to the disjoint resonant clock networks. The inductors comprising the LC tanks are used as the receiver circuit for the links, essentially eliminating the need for additional circuits and/or interconnect resources during pre-bond test. Recent FPGAs are quite complex circuits which provide reconfigurablity at the cost of lower performance and higher power consumption as compared to ASIC circuits. Exploiting a large number of programmable switches, routing structures are mainly responsible for performance degradation in FPAGs. Employing 3-D technology can providemore efficient switches which drastically improve the performance and reduce the power consumption of the FPGA. RRAM switches are one of the most promising candidates to improve the FPGA routing architecture thanks to their low on-resistance and non-volatility. Along with the configurable switches, buffers are the other important element of the FPGAs routing structure. Different characteristics of RRAM switches change the properties of signal paths in RRAM-based FPGAs. The on resistance of RRAMswitches is considerably lower than CMOS pass gate switches which results in lower RC delay for RRAM-based routing paths. This different nature in critical path and signal delay in turn affect the need for intermediate buffers. Thus the buffer allocation should be reconsidered. In the last part of this research, the effect of intermediate buffers on signal propagation delay is studied and a modified buffer allocation scheme for RRAM-based FPGA routing path is proposed

Analyse et caractérisation des couplages substrat et de la connectique dans les circuits 3D : Vers des modèles compacts

The 3D integration is the most promising technological solution to track the level of integration dictated by Moore's Law (see more than Moore, Moore versus more). It leads to important research for a dozen years. It can superimpose different circuits and components in one box. Its main advantage is to allow a combination of heterogeneous and highly specialized technologies for the establishment of a complete system, while maintaining a high level of performance with very short connections between the different circuits. The objective of this work is to provide consistent modeling via crossing, and / or contacts in the substrate, with various degrees of finesse / precision to allow the high-level designer to manage and especially to optimize the partitioning between the different strata. This modelization involves the development of multiple views at different levels of abstraction: the physical model to "high level" model. This would allow to address various issues faced in the design process: - The physical model using an electromagnetic simulation based on 2D or 3D ( finite element solver ) is used to optimize the via (materials, dimensions etc..) It determines the electrical performance of the via, including high frequency. Electromagnetic simulations also quantify the coupling between adjacent via. - The analytical compact of via their coupling model, based on a description of transmission line or Green cores is used for the simulations at the block level and Spice type simulations. Analytical models are often validated against measurements and / or physical models.L’intégration 3D est la solution technologique la plus prometteuse pour suivre le niveau d’intégration dictée par la loi de Moore (cf. more than Moore, versus more Moore). Elle entraine des travaux de recherche importants depuis une douzaine d’années. Elle permet de superposer différents circuits et composants dans un seul boitier. Son principal avantage est de permettre une association de technologies hétérogènes et très spécialisées pour la constitution d’un système complet, tout en préservant un très haut niveau de performance grâce à des connexions très courtes entre ces différents circuits. L’objectif de ce travail est de fournir des modélisations cohérentes de via traversant, ou/et de contacts dans le substrat, avec plusieurs degrés de finesse/précision, pour permettre au concepteur de haut niveau de gérer et surtout d’optimiser le partitionnement entre les différentes strates. Cette modélisation passe par le développement de plusieurs vues à différents niveaux d’abstraction: du modèle physique au modèle « haut niveau ». Elle devait permettre de répondre à différentes questions rencontrées dans le processus de conception :- le modèle physique de via basé sur une simulation électromagnétique 2D ou 3D (solveur « éléments finis ») est utilisé pour optimiser l’architecture du via (matériaux, dimensions etc.) Il permet de déterminer les performances électriques des via, notamment en haute fréquence. Les simulations électromagnétiques permettent également de quantifier le couplage entre via adjacents. - le modèle compact analytique de via et de leur couplage, basé sur une description de type ligne de transmission ou noyaux de Green, est utilisé pour les simulations au niveau bloc, ainsi que des simulations de type Spice. Les modèles analytiques sont souvent validés par rapport à des mesures et/ou des modèles physiques