Modelling thermal effects in machining of carbon fiber reinforced polymer composites

Machining-induced damage is commonly observed when manufacturing components based on carbon fiber reinforced polymer (CFRP) composites. Despite the importance of thermal effects in machining CFRPs, this problem has been poorly analyzed in the literature. Predictive tools are not available for thermal phenomena involved during cutting, while only few experimental studies have been found. In this paper, a three-dimensional (3D) finite element model of orthogonal machining of CFRPs including thermal effects is presented. Predicted thermal and mechanical intralaminar damage showed strong influence of fiber orientation. Thermally affected area was larger than mechanically damaged zone. This fact confirms the importance of accounting for thermal effects when modelling CFRP machining.The authors acknowledge the financial support for the work to the Ministry of Economy and Competitiveness of Spain under the projects DPI2011-25999 and DPI2010-15123.Publicad

Modelling and simulation of metal cutting by finite element method

Thesis (Master)--Izmir Institute of Technology, Mechanical Engineering, Izmir, 2009Includes bibliographical references (leaves: 70-73)Text in English; Abstract: Turkish and Englishxiii, 73 leavesMetal cutting is one of the most widely used manufacturing techniques in the industry and there are lots of studies to investigate this complex process in both academic and industrial world. Predictions of important process variables such as temperature, cutting forces and stress distributions play significant role on designing tool geometries and optimising cutting conditions. Researchers find these variables by using experimental techniques which makes the investigation very time consuming and expensive. At this point, finite element modelling and simulation becomes main tool. These important cutting variables can be predicted without doing any experiment with finite element method. This thesis covers a study on modelling and simulation of orthogonal metal cutting by finite element method. For this purpose, orthogonal cutting simulations of AISI 1045 steel are performed and model used in simulations is validated. At first step, effects of work piece flow stress and friction models on cutting variables such as cutting forces, chip geometry and temperature are investigated by comparing simulation results with experimental results available in the literature. Then, mechanical and thermal analyses are performed. Lastly, effects of rake angle and tool tip radius on strain, temperature and stress distributions are investigated

Modeling Chip Formation in Orthogonal Metal Cutting using Finite Element Analysis

This thesis presents the simulation of chip formation in orthogonal metal cutting to evaluate the predictive capabilities of finite element code DYNA 3D. The Johnson and Cook constitutive model for materials, OFHC Copper, Aluminum 2024 T351, and Aluminum 6061 T6 alloy were incorporated into the simulation to account for the effects of strain hardening, strain rate hardening, and thermal softening effects during machining. Calculated values for the Johnson and Cook constitutive constants for Aluminum 6061 T6 alloy were determined from the literature. The model was compared to experimentally measured shear angles, chip thickness, chip velocity, and forces from the literature to evaluate the accuracy of the finite element code for a range machining strain rates. In an attempt to determine the predictive capabilities of DYNA 3D a strain rate regime of 10+3 s-1 to 10+4 s-1 was defined as the optimal strain rate regime for the orthogonal metal cutting application

Modelling the Effects of Friction on Tool-Chip Interface Temperature During Orthogonal Cutting of Al6061-T6 Aluminium Alloy

© IEOM Society International - IEOM 2019In this work, finite element simulations based on the analytical model derived with the MATLAB software were used to establish the temperature fields within the cutting tool and tool-chip interface. The average tool-chip interface temperature model was simulated and the simulation results were compared with experimental results for validation. At a maximum cutting speed of 90 m/min, the maximum temperature obtained from the experiment was 410 oC, at same rake angle of 0o. However, the developed model predicted 490 oC under the same conditions. The higher value obtained by the model can be attributed to the negligence of heat losses to the surrounding by both convection and radiation modes, as an assumption in the formulated model. A similar trend of these results was also recorded for the case of rake angle and feed rate of 30o and 0.0635 mm/rev, respectively. It was observed that the simulation results and experimental measurements for the average tool-chip interface temperature agreed significantly.Final Published versio

FEA modeling of orthogonal cutting of steel: a review

Orthogonal cutting is probably the most studied machining operation for metals. Its simulation with the Finite Element Analysis (FEA) method is of paramount academic interest. 2D models, and to a lesser extent 3D models, have been developed to predict cutting forces, chip formation, heat generation and temperature fields, residual stress distribution and tool wear. This paper first presents a brief review of scientific literature with focus on FEA modelling of the orthogonal cutting process for steels. Following, emphasis is put on the building blocks of the simulation model, such as the formulation of the mechanical problem, the material constitutive model, the friction models and damage laws

Numerical and analytical modeling of orthogonal cutting : The link between local variables and global contact characteristics

The response of the tool–chip interface is characterized in the orthogonal cutting process by numerical and analytical means and compared to experimental results. We study the link between local parameters (chip temperature, sliding friction coefficient, tool geometry) and overall friction characteristics depicting the global response of the tool–chip interface. Sticking and sliding contact regimes are described. The overall friction characteristics of the tool are represented by two quantities: (i) the mean friction coefficient qualifies the global response of the tool rake face (tool edge excluded) and (ii) the apparent friction coefficient reflects the overall response of the entire tool face, the effect of the edge radius being included. When sticking contact is dominant the mean friction coefficient is shown to be essentially the ratio of the average shear flow stress along the sticking zone by the average normal stress along the contact zone. The dependence of overall friction characteristics is analyzed with respect to tool geometry and cutting conditions. The differences between mean friction and apparent friction are quantified. It is demonstrated that the evolutions of the apparent and of the mean friction coefficients are essentially controlled by thermal effects. Constitutive relationships are proposed which depict the overall friction characteristics as functions of the maximum chip temperature along the rake face. This approach offers a simple way for describing the effect of cutting conditions on the tool–chip interface response. Finally, the contact length and contact forces are analyzed. Throughout the paper, the consistency between numerical, analytical and experimental results is systematically checked

Comprehension of chip formation in laser assisted machining

Laser Assisted Machining (LAM) improves the machinability of materials by locally heating the workpiece just prior to cutting. Experimental investigations have confirmed that the cutting force can be decreased, by as much as 40%, for various materials. In order to understand the effect of the laser on chip formation and on the temperature fields in the different deformation zones, thermo-mechanical simulations were undertaken. A thermo-mechanical model for chip formation was also undertaken. Experimental tests for the orthogonal cutting of 42CrMo4 steel were used to validate the simulation. The temperature fields allow us to explain the reduction in the cutting force and the resulting residual stress fields in the workpiece.Contrat Plan Etat Région (CPER) Pays de la Loir

Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC copper

The authors gratefully acknowledge the support received from IC ARTS and CEA ValducSuperfinishing machining has a particular impact on cutting mechanics, surface integrity and local electrochemical behavior. In fact, material removal during this process induces geometrical, mechanical and micro-structural modifications in the machined surface and sub-surface. However, a conventional 3D cutting process is still complex to study in terms of analytical/numerical modeling and experimental process monitoring. So, researchers are wondering if a less intricate configuration such as orthogonal cutting would be able to provide information about surface integrity as close as possible to that one generated by a 3D cutting process. For that reason, in the present paper, two different machining configurations were compared: face turning and orthogonal cutting. The work material is oxygen free high conductivity copper (OFHC) and the cutting tools are uncoated cemented carbide. The research work was performed in three steps. In the first step, the process mechanics of superfinishing machining of OFHC copper was performed. In the second step, the surface integrity and the chemical behavior of the machined samples were analyzed. Finally, in the third step, correlations between input parameters and output measures were conducted using statistical techniques. Results show that when applying low ratios between the uncut chip thickness and the cutting edge radius, the surface integrity and cutting energy are highly affected by the ploughing phenomenon. Otherwise, the most relevant cutting parameter is the feed. In order to compare face turning with orthogonal cutting, a new geometrical parameter was introduced, which has a strong effect in the electrochemical behavior of the machined surface

Development of Thermomechanical Model for the Analysis of Effects of Friction and Cutting Speed on Temperature Distribution around AISI 316L During Orthogonal Machining

In metal cutting,severe deformation takes place in the vicinity of the cutting edge of the high strain-rate and an increase in temperature is observed. Deformation behaviour of the work material in the primary and secondary zones is highly sensitive to the cutting conditions. Also, the frictional conditions between the tool and the chip and tool and the workpiece are highly complex and sensitive to the cutting conditions. As a result, the stresses and temperatures at tool-chip interface and around the cutting edge can be critically high in some cutting conditions and can cause excessive tool wear or premature tool failure. This research work focuses on the accurate prediction of the distribution of the process variables such as stresses and temperatures with the Finite Element (FE) Analysis to identify optimum cutting conditions, tool material, edge geometry and coating in order to help improve productivity and quality of machining operations. Effects of work material flow stress and interfacial friction at chip-tool interface on the accuracy of the predicated process variables in FE simulations are also analyzed. Specifically, friction models and cutting speed are varied to predict the effect on the temperature distribution, stresses and strain on the workpiece and tool chip during orthogonal cutting process. The result showed that an increase in coefficient of friction will cause an increase in thermal, force and mechanical variables during machining. Thus, the higher the coefficient of friction, the higher, the cutting forces, temperature, stress, and strain

Modeling of temperature distribution in orthogonal cutting with dual-zone contact at rake face

In this study, an analytical model is developed in order to calculate the temperature distribution in orthogonal cutting with dual-zone contact at the rake face. The study focuses on heat generation at the primary shear zone and at the rake face. The material behavior at the primary shear zone is represented by Johnson-Cook constitutive equation whereas the contact at the rake face is modeled by sticking and sliding friction zones. This new temperature distribution model allows obtaining the maximum temperature at the rake face and helps determining two dimensional temperature distribution in the chip. The simulation results obtained from the developed model are also compared with experimental results where good agreement is observed