Improving processor efficiency through thermal modeling and runtime management of hybrid cooling strategies

One of the main challenges in building future high performance systems is the ability to maintain safe on-chip temperatures in presence of high power densities. Handling such high power densities necessitates novel cooling solutions that are significantly more efficient than their existing counterparts. A number of advanced cooling methods have been proposed to address the temperature problem in processors. However, tradeoffs exist between performance, cost, and efficiency of those cooling methods, and these tradeoffs depend on the target system properties. Hence, a single cooling solution satisfying optimum conditions for any arbitrary system does not exist. This thesis claims that in order to reach exascale computing, a dramatic improvement in energy efficiency is needed, and achieving this improvement requires a temperature-centric co-design of the cooling and computing subsystems. Such co-design requires detailed system-level thermal modeling, design-time optimization, and runtime management techniques that are aware of the underlying processor architecture and application requirements. To this end, this thesis first proposes compact thermal modeling methods to characterize the complex thermal behavior of cutting-edge cooling solutions, mainly Phase Change Material (PCM)-based cooling, liquid cooling, and thermoelectric cooling (TEC), as well as hybrid designs involving a combination of these. The proposed models are modular and they enable fast and accurate exploration of a large design space. Comparisons against multi-physics simulations and measurements on testbeds validate the accuracy of our models (resulting in less than 1C error on average) and demonstrate significant reductions in simulation time (up to four orders of magnitude shorter simulation times). This thesis then introduces temperature-aware optimization techniques to maximize energy efficiency of a given system as a whole (including computing and cooling energy). The proposed optimization techniques approach the temperature problem from various angles, tackling major sources of inefficiency. One important angle is to understand the application power and performance characteristics and to design management techniques to match them. For workloads that require short bursts of intense parallel computation, we propose using PCM-based cooling in cooperation with a novel Adaptive Sprinting technique. By tracking the PCM state and incorporating this information during runtime decisions, Adaptive Sprinting utilizes the PCM heat storage capability more efficiently, achieving 29\% performance improvement compared to existing sprinting policies. In addition to the application characteristics, high heterogeneity in on-chip heat distribution is an important factor affecting efficiency. Hot spots occur on different locations of the chip with varying intensities; thus, designing a uniform cooling solution to handle worst-case hot spots significantly reduces the cooling efficiency. The hybrid cooling techniques proposed as part of this thesis address this issue by combining the strengths of different cooling methods and localizing the cooling effort over hot spots. Specifically, the thesis introduces LoCool, a cooling system optimizer that minimizes cooling power under temperature constraints for hybrid-cooled systems using TECs and liquid cooling. Finally, the scope of this work is not limited to existing advanced cooling solutions, but it also extends to emerging technologies and their potential benefits and tradeoffs. One such technology is integrated flow cell array, where fuel cells are pumped through microchannels, providing both cooling and on-chip power generation. This thesis explores a broad range of design parameters including maximum chip temperature, leakage power, and generated power for flow cell arrays in order to maximize the benefits of integrating this technology with computing systems. Through thermal modeling and runtime management techniques, and by exploring the design space of emerging cooling solutions, this thesis provides significant improvements in processor energy efficiency.2018-07-09T00:00:00

Modeling and optimization of high-performance many-core systems for energy-efficient and reliable computing

Thesis (Ph.D.)--Boston UniversityMany-core systems, ranging from small-scale many-core processors to large-scale high performance computing (HPC) data centers, have become the main trend in computing system design owing to their potential to deliver higher throughput per watt. However, power densities and temperatures increase following the growth in the performance capacity, and bring major challenges in energy efficiency, cooling costs, and reliability. These challenges require a joint assessment of performance, power, and temperature tradeoffs as well as the design of runtime optimization techniques that monitor and manage the interplay among them. This thesis proposes novel modeling and runtime management techniques that evaluate and optimize the performance, energy, and reliability of many-core systems. We first address the energy and thermal challenges in 3D-stacked many-core processors. 3D processors with stacked DRAM have the potential to dramatically improve performance owing to lower memory access latency and higher bandwidth. However, the performance increase may cause 3D systems to exceed the power budgets or create thermal hot spots. In order to provide an accurate analysis and enable the design of efficient management policies, this thesis introduces a simulation framework to jointly analyze performance, power, and temperature for 3D systems. We then propose a runtime optimization policy that maximizes the system performance by characterizing the application behavior and predicting the operating points that satisfy the power and thermal constraints. Our policy reduces the energy-delay product (EDP) by up to 61.9% compared to existing strategies. Performance, cooling energy, and reliability are also critical aspects in HPC data centers. In addition to causing reliability degradation, high temperatures increase the required cooling energy. Communication cost, on the other hand, has a significant impact on system performance in HPC data centers. This thesis proposes a topology-aware technique that maximizes system reliability by selecting between workload clustering and balancing. Our policy improves the system reliability by up to 123.3% compared to existing temperature balancing approaches. We also introduce a job allocation methodology to simultaneously optimize the communication cost and the cooling energy in a data center. Our policy reduces the cooling cost by 40% compared to cooling-aware and performance-aware policies, while achieving comparable performance to performance-aware policy

GreenCool: An Energy-Efficient Liquid Cooling Design Technique for 3-D MPSoCs Via Channel Width Modulation

Liquid cooling using interlayer microchannels has appeared as a viable and scalable packaging technology for 3-D multiprocessor system-on-chips (MPSoCs). Microchannel-based liquid cooling, however, can substantially increase the on-chip thermal gradients, which are undesirable for reliability, performance, and cooling efficiency. In this paper, we present GreenCool, an optimal design methodology for liquid-cooled 3-D MPSoCs. GreenCool simultaneously minimizes the cooling energy for a given system while maintaining thermal gradients and peak temperatures under safe limits. This is accomplished by tuning the heat transfer characteristics of the microchannels using channel width modulation. Channel width modulation is compatible with the current process technologies and incurs minimal additional fabrication costs. Through an extensive set of experiments, we show that channel width modulation is capable of complementing and enhancing the benefits of temperature-aware floorplanning. We also experiment with a 16-core 3-D system with stacked dynamic random-access memory, for which GreenCool improves energy efficiency by up to 53% with respect to no channel modulation

Overcoming the Challenges for Multichip Integration: A Wireless Interconnect Approach

The physical limitations in the area, power density, and yield restrict the scalability of the single-chip multicore system to a relatively small number of cores. Instead of having a large chip, aggregating multiple smaller chips can overcome these physical limitations. Combining multiple dies can be done either by stacking vertically or by placing side-by-side on the same substrate within a single package. However, in order to be widely accepted, both multichip integration techniques need to overcome significant challenges. In the horizontally integrated multichip system, traditional inter-chip I/O does not scale well with technology scaling due to limitations of the pitch. Moreover, to transfer data between cores or memory components from one chip to another, state-of-the-art inter-chip communication over wireline channels require data signals to travel from internal nets to the peripheral I/O ports and then get routed over the inter-chip channels to the I/O port of the destination chip. Following this, the data is finally routed from the I/O to internal nets of the target chip over a wireline interconnect fabric. This multi-hop communication increases energy consumption while decreasing data bandwidth in a multichip system. On the other hand, in vertically integrated multichip system, the high power density resulting from the placement of computational components on top of each other aggravates the thermal issues of the chip leading to degraded performance and reduced reliability. Liquid cooling through microfluidic channels can provide cooling capabilities required for effective management of chip temperatures in vertical integration. However, to reduce the mechanical stresses and at the same time, to ensure temperature uniformity and adequate cooling competencies, the height and width of the microchannels need to be increased. This limits the area available to route Through-Silicon-Vias (TSVs) across the cooling layers and make the co-existence and co-design of TSVs and microchannels extreamly challenging. Research in recent years has demonstrated that on-chip and off-chip wireless interconnects are capable of establishing radio communications within as well as between multiple chips. The primary goal of this dissertation is to propose design principals targeting both horizontally and vertically integrated multichip system to provide high bandwidth, low latency, and energy efficient data communication by utilizing mm-wave wireless interconnects. The proposed solution has two parts: the first part proposes design methodology of a seamless hybrid wired and wireless interconnection network for the horizontally integrated multichip system to enable direct chip-to-chip communication between internal cores. Whereas the second part proposes a Wireless Network-on-Chip (WiNoC) architecture for the vertically integrated multichip system to realize data communication across interlayer microfluidic coolers eliminating the need to place and route signal TSVs through the cooling layers. The integration of wireless interconnect will significantly reduce the complexity of the co-design of TSV based interconnects and microchannel based interlayer cooling. Finally, this dissertation presents a combined trade-off evaluation of such wireless integration system in both horizontal and vertical sense and provides future directions for the design of the multichip system

Attaining Single-Chip, High-Performance Computing Through 3D Systems with Active Cooling

Three-dimensional (3D) stacking is an attractive method for designing large manycore chips as it provides high transistor integration densities, improves manufacturing yield due to smaller chip area, reduces wirelength and capacitance, and enables heterogeneous integration of different technologies on the same chip. Stacking, however, significantly increases the thermal resistivity and the on-chip temperatures. In fact, temperature is among the major manufacturing challenges for 3D design. Active cooling, where the chip is cooled through the liquid flowing in built-in microchannels or through a cold plate, has emerged as a viable cooling alternative for high-performance 3D manycore systems. Liquid cooling is more efficient in removing the heat in comparison to conventional cooling methods with heat sinks and fans. Nevertheless, the dynamically changing nature of workloads running on manycore systems require runtime techniques to enable energy-efficient, reliable, and high-performance operation of liquid-cooled 3D systems. This article focuses on the benefits and the challenges of 3D design, and discusses novel techniques to integrate predictive cooling control with chip-level thermal management methods such as job scheduling and voltage frequency scaling. The key message is that 3D liquid-cooled systems with intelligent runtime management provide an energy-efficient solution to designing future single-chip high-performance manycore architectures

Temperature-Aware Design and Management for 3D Multi-Core Architectures

Vertically-integrated 3D multiprocessors systems-on-chip (3D MPSoCs) provide the means to continue integrating more functionality within a unit area while enhancing manufacturing yields and runtime performance. However, 3D MPSoCs incur amplified thermal challenges that undermine the corresponding reliability. To address these issues, several advanced cooling technologies, alongside temperature-aware design-time optimizations and run-time management schemes have been proposed. In this monograph, we provide an overall survey on the recent advances in temperature-aware 3D MPSoC considerations. We explore the recent advanced cooling strategies, thermal modeling frameworks, design-time optimizations and run-time thermal management schemes that are primarily targeted for 3D MPSoCs. Our aim of proposing this survey is to provide a global perspective, highlighting the advancements and drawbacks on the recent state-of-the-ar

Electronics Thermal Management in Information and Communications Technologies: Challenges and Future Directions

This paper reviews thermal management challenges encountered in a wide range of electronics cooling applications from large-scale (data center and telecommunication) to smallscale systems (personal, portable/wearable, and automotive). This paper identifies drivers for progress and immediate and future challenges based on discussions at the 3rd Workshop on Thermal Management in Telecommunication Systems and Data Centers held in Redwood City, CA, USA, on November 4–5, 2015. Participants in this workshop represented industry and academia, with backgrounds ranging from data center thermal management and energy efficiency to high-performance computing and liquid cooling, thermal management in wearable and mobile devices, and acoustic noise management. By considering a wide range of electronics cooling applications with different lengths and time scales, this paper identifies both common themes and diverging views in the thermal management community

CoMeT: An Integrated Interval Thermal Simulation Toolchain for 2D, 2.5 D, and 3D Processor-Memory Systems

Processing cores and the accompanying main memory working in tandem enable the modern processors. Dissipating heat produced from computation, memory access remains a significant problem for processors. Therefore, processor thermal management continues to be an active research topic. Most thermal management research takes place using simulations, given the challenges of measuring temperature in real processors. Since core and memory are fabricated on separate packages in most existing processors, with the memory having lower power densities, thermal management research in processors has primarily focused on the cores. Memory bandwidth limitations associated with 2D processors lead to high-density 2.5D and 3D packaging technology. 2.5D packaging places cores and memory on the same package. 3D packaging technology takes it further by stacking layers of memory on the top of cores themselves. Such packagings significantly increase the power density, making processors prone to heating. Therefore, mitigating thermal issues in high-density processors (packaged with stacked memory) becomes an even more pressing problem. However, given the lack of thermal modeling for memories in existing interval thermal simulation toolchains, they are unsuitable for studying thermal management for high-density processors. To address this issue, we present CoMeT, the first integrated Core and Memory interval Thermal simulation toolchain. CoMeT comprehensively supports thermal simulation of high- and low-density processors corresponding to four different core-memory configurations - off-chip DDR memory, off-chip 3D memory, 2.5D, and 3D. CoMeT supports several novel features that facilitate overlying system research. Compared to an equivalent state-of-the-art core-only toolchain, CoMeT adds only a ~5% simulation-time overhead. The source code of CoMeT has been made open for public use under the MIT license.Comment: https://github.com/marg-tools/CoMe

System-Level Thermal-Aware Design of 3D Multiprocessors with Inter-Tier Liquid Cooling

Rising chip temperatures and aggravated thermal reliability issues have characterized the emergence of 3D multiprocessor system-on-chips (3D-MPSoCs), necessitating the development of advanced cooling technologies. Microchannel based inter-tier liquid cooling of ICs has been envisaged as the most promising solution to this problem. A system-level thermal-aware design of electronic systems becomes imperative with the advent of these new cooling technologies, in order to preserve the reliable functioning of these ICs and effective management of the rising energy budgets of high-performance computing systems. This paper reviews the recent advances in the area of systemlevel thermal modeling and management techniques for 3D multiprocessors with advanced liquid cooling. These concepts are combined to present a vision of a green data center of the future which reduces the CO2 emissions by reusing the heat it generates