Reconfigurable Reflectarrays and Array Lenses for Dynamic Antenna Beam Control: A Review

Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area in recent years. The paper describes the fundamental design approaches employed in realizing reconfigurable designs, and explores advanced capabilities of these nascent architectures, such as multi-band operation, polarization manipulation, frequency agility, and amplification. Finally, the paper concludes by discussing future challenges and possibilities for these antennas.Comment: 16 pages, 12 figure

Planar microwave filters with electronically tunability and other novel configurations

In order to meet the increasing demands of advance wireless communications and radar systems, several novel types of bandpass filters and bandstop filters have been developed in this thesis. A new type of varactor-tuned dual-mode bandpass filters have been presented to achieve a nearly constant absolute bandwidth over a wide tuning range by using a single DC bias circuit. Since the two operating modes (i.e., the odd and even modes) in a dualmode microstrip open-loop resonator do not couple to each other, tuning the passband frequency is accomplished by merely changing the two modal frequencies proportionally. Design equations and procedures are derived, and two two-pole tunable bandpass filters and a four-pole tunable bandpass filter of this type are demonstrated experimentally. Miniature microstrip doublet dual-mode filters that exhibit quasi-elliptic function response without using any cross coupling have been developed. It shows that a single two-pole filter or the doublet can produce two transmission zeros resulting from a double behaviour of the dual-mode resonator of this type. Electromagnetic (EM) simulation and experiment results of the proposed filters are described. Parallel feed configuration of a microstrip quasi-elliptic function bandpass filter has been built with a pair of open-loop dual-mode resonators. By employing this new coupling scheme, a novel filter topology with three-pole quasi-elliptic function frequency response can be obtained, leading to good passband performance, such as low insertion loss and good matching at the mid-band of passband. A designed three-pole bandpass filter of this type is demonstrated experimentally. A new class of dual-band filters based on non-degenerate dual-mode microstrip slow-wave open-loop resonators, which support two non-degenerate modes that do not couple, have been introduced. Different feed schemes that affect the filtering characteristics are investigated. Examples of dual-band filters of this type are described with simulation and experiment results. iii In order to achieve a wide spurious-free upper passband, a novel design of bandstop filter with cancellation of first spurious mode by using coupled three-section step impedance resonators (SIRs) has been developed. This cancellation occurs when two transmission poles coincide with the first spurious mode (transmission zero) by properly choosing the step impedance ratio and the gap between the SIR and the main transmission line. A stripline bandstop filter and a microstrip bandstop filter of this type are designed, fabricated and tested. As a preliminary investigation, the microstrip filter is tuned electronically using ferroelectric thin film varactors

Miniaturised and reconfigurable planar filters for ultra-wideband applications

An increasing demand for electromagnetic spectrum has resulted from the emergence of feature-rich and faster throughputs wireless applications. This necessitates the developments of dynamic reconfigurable or multifunctional systems to better exploit the existing spectrum. Future wireless devices will be expected to communicate over several bands with various other devices in order to fine tune the services they provide to the user. Each band may require a separate RF transceiver and such modern wireless multi-band multi-mode communication systems call for high performance, highly integrated compact modules. Since the Federal Communications Commission (FCC) released the unlicensed frequency band 3.1-10.6 GHz for ultra-wideband (UWB) commercial communications, the development race for commercialising UWB technology has seen a dramatic increase around the world. The aim of this research is to develop reconfigurable planar microwave filters for ultrawideband applications. The project investigates some key design issues of reconfigurable filters, which are being observed constantly in the latest development and realisation of microwave filters. Both analytical and numerical methods are performed to construct a realistic and functional design. Two different types of frequency reconfigurability are investigated in this thesis: discrete (e.g. PIN diode, Optical switch) and continuous (e.g. varactor diode). Using the equivalent circuits and considering the direct coupled filter structure in most cases, several topologies with attractive features are developed for future communication systems. The proposed works may be broadly categorised into three sections as follows. The first section explores a square ring shape close loop resonator along with an opencircuited stub in the symmetry plane. To realise a reconfigurable frequency states within the same spectrum, an innovative approach is developed for this case. An optical or photoconductive switch, comprised of a silicon die activated using near infrared light is investigated as a substitute of PIN diode and performances are evaluated to compare the feasibilities. In addition, a in-band interference rejection technique via externally coupled Tshape resonator is shown. However, it is observed that both structures achieve significant size reductions by utilising the inner part of the resonators. To improve the filter selectivity, a convenient design approach generating a pair of transmission zeros between both passband edges and a single zero in the stop band for harmonic suppression is discussed in the second section. Moreover, the development of notched rejection bands are studied and several novel methods to create a single and multiple notched bands employing the square ring shape structure are proposed. On inspection, it is found that the notch structure can be implemented without deteriorating the filter performances. The discussions are supplemented with detailed design examples which are accompanied by theoretical, simulated and experimental results in order to illustrate the filter development process and showcase practical filter performance. The third section reveals a novel highly compact planar dual-mode resonator with sharp rejections characteristics for UWB applications. A bandwidth reconfiguring technique is demonstrated by splitting its even-mode resonance. Filter structure with the dual-mode resonator is shown to have a relatively wide tuning range, significantly low insertion loss and a constant selectivity along with frequency variations in comparison to similar published works. Finally, the earlier dual-mode structure are modified to realise a dual wideband behaviour. A detail analysis with comprehensive design procedures is outlined and a solution for controlling the frequency bandwidths independently according to the application interest is provided. In line with the previous section, experimental verification is presented to support and supplement the discussions

Development of tunable and miniature microwave filters for modern wireless communications

Due to the increasing demand for new wireless services and applications, the high level of integration and the coexistence of multi-standard (MS) or multi-band operations into a single device are becoming defining trends in designing microwave filters. This has driven considerable technological advances in reconfigurable/tunable and miniaturized filters. More specifically, reconfigurable/tunable filters that tune to different frequency bands instead of classical filter banks have great potential to significantly reduce the system size and complexity; while reducing the filter size becomes essential to achieve the highest degree of integration density in compact and portable wireless devices. In the light of this scenario, the objective of this dissertation is to develop the new design technologies, concepts and filtering configurations for tunable microstrip filters and compact passive microwave filters. To this aim, this dissertation is divided into two main parts. The first part (Part I) focuses on the designs of novel varactor-tuned microstrip filters with advanced performances. In this aspect, new topologies for realizing tunable lowpass and highpass filters are firstly developed. State-of-the-art performances, including wide tuning range, high selectivity with multiple transmission zeros, low insertion loss and compact size for all the tuning states are obtained in both of these filters. Secondly, two novel classes of tunable bandpass filters are presented. One of them is designed based on varactor-loaded parallel-coupled microstrip lines (PCML) and short-circuited stubs, which allows the lower passband edge together with two transmission zeros located around the lower passband skirt to be reconfigured separately. While the other tunable bandpass filter is constructed by the combination of tunable bandpass and lowpass filters, featuring both centre frequency and bandwidth tunabilities, as well as high selectivity with abundant transmission zeros. Furthermore, a new concept of tunable lossy filter is demonstrated, which attempts to achieve an equivalent high-Q tunable performance by using low-Q resonators. This concept makes the presented tunable combline filter interesting for some frequency-agile applications in which the low in-band loss variation and high selectivity are much desired while the absolute insertion loss can be a tradeoff. The second part (Part II) is devoted to the design of miniaturized passive microwave filters with improved characteristics. For this, the concept of artificial right-handed and left-handed transmission lines are applied to the signal interference filtering topology, which results in a compact circuit size and good out-of-band performance. In particular, for a further size reduction, such filter is implemented in the forms of multilayered structure by using liquid crystal polymer (LCP) technology. Additionally, another two types of miniaturized bandpass filters using stepped impedance resonators are demonstrated, which are implemented based on different fabrication processes (i.e. LCP bonded multilayer PCB technology and a standard planar PCB technology). Among their main features, the compact size, wide passband, broad stopband with multiple transmission zeros and circuit simplicity are highlighted. For all the proposed design techniques and filtering structures, exhaustive theoretical analyses are done, and design equations and guide rules are provided. Furthermore, all the proposed schemes and/or ideas have been experimentally validated through the design, implementation and measurement of different filters. The fabrication processes of multilayer technology utilized: liquid crystal polymer (LCP) technology and liquid crystal polymer (LCP) bonded multilayer printed circuit board (PCB) technology, are also demonstrated for reference. All of the results achieved in this dissertation make the proposed filters very attractive for their use in modern wireless communication systems

Development of turnable and miniature microwave filters for modern wireless communication

Due to the increasing demand for new wireless services and applications, the high level of integration and the coexistence of multi-standard (MS) or multi-band operations into a single device are becoming defining trends in designing microwave filters. This has driven considerable technological advances in reconfigurable/tunable and miniaturized filters. More specifically, reconfigurable/tunable filters that tune to different frequency bands instead of classical filter banks have great potential to significantly reduce the system size and complexity; while reducing the filter size becomes essential to achieve the highest degree of integration density in compact and portable wireless devices. In the light of this scenario, the objective of this dissertation is to develop the new design technologies, concepts and filtering configurations for tunable microstrip filters and compact passive microwave filters. To this aim, this dissertation is divided into two main parts. The first part (Part I) focuses on the designs of novel varactor-tuned microstrip filters with advanced performances. In this aspect, new topologies for realizing tunable lowpass and highpass filters are firstly developed. State-of-the-art performances, including wide tuning range, high selectivity with multiple transmission zeros, low insertion loss and compact size for all the tuning states are obtained in both of these filters. Secondly, two novel classes of tunable bandpass filters are presented. One of them is designed based on varactor-loaded parallel-coupled microstrip lines (PCML) and short-circuited stubs, which allows the lower passband edge together with two transmission zeros located around the lower passband skirt to be reconfigured separately. While the other tunable bandpass filter is iii constructed by the combination of tunable bandpass and lowpass filters, featuring both centre frequency and bandwidth tunabilities, as well as high selectivity with abundant transmission zeros. Furthermore, a new concept of tunable lossy filter is demonstrated, which attempts to achieve an equivalent high-Q tunable performance by using low-Q resonators. This concept makes the presented tunable combline filter interesting for some frequency-agile applications in which the low in-band loss variation and high selectivity are much desired while the absolute insertion loss can be a tradeoff. The second part (Part II) is devoted to the design of miniaturized passive microwave filters with improved characteristics. For this, the concept of artificial right-handed and left-handed transmission lines are applied to the signal interference filtering topology, which results in a compact circuit size and good out-of-band performance. In particular, for a further size reduction, such filter is implemented in the forms of multilayered structure by using liquid crystal polymer (LCP) technology. Additionally, another two types of miniaturized bandpass filters using stepped impedance resonators are demonstrated, which are implemented based on different fabrication processes (i.e. LCP bonded multilayer PCB technology and a standard planar PCB technology). Among their main features, the compact size, wide passband, broad stopband with multiple transmission zeros and circuit simplicity are highlighted. For all the proposed design techniques and filtering structures, exhaustive theoretical analyses are done, and design equations and guide rules are provided. Furthermore, all the proposed schemes and/or ideas have been experimentally validated through the design, implementation and measurement of different filters. The fabrication processes of multilayer technology utilized: liquid crystal polymer (LCP) technology and liquid crystal polymer (LCP) bonded multilayer printed circuit board (PCB) technology, are also demonstrated for reference. All of the results achieved in this dissertation make the proposed filters very attractive for their use in modern wireless communication systems.MultiWaves Project (PIRSES-GA-2010-247532) of the Seventh Framework Programme (FP7), European Commission

Miniaturised bandpass filters for wireless communications

The wireless industry has seen exceptional development over the past few decades due to years of sustained military and commercial enterprise. While the electromagnetic spectrum is becoming increasingly congested, there is a growing tendency to strive for higher bandwidths, faster throughputs, greater versatility, compatibility and interoperability in current and emerging wireless technologies. Consequently, an increasingly stringent specification is imposed upon the frequency utilization of wireless devices. New challenges are constantly being discovered in the development and realization of RF and microwave filters, which have not only sustained but fuelled microwave filter research over the many years. These developments have encouraged new solutions and techniques for the realization of compact, low loss, highly selective RF and microwave bandpass filters. The theme of this dissertation is the realization of planar compact performance microwave and RF bandpass filters for wireless communication systems. The work may be broadly categorised into three sections as follows. The first section presents a novel compact planar dual-mode resonator with several interesting and attractive features. Generally, planar microwave dual-mode resonators are known to half the filter footprint. However, it is found that the proposed resonator is capable of achieving further size reductions. In addition the resonator inherently possesses a relatively wide stopband as the lowest spurious harmonic resonance is observed at thrice the fundamental frequency. Properties of this resonator, such as these and more are explored in depth to arrive at an accurate electrical equivalent circuit, which is used as the basis for high order filter design. The application of these resonators in the design of bandpass filters is the subject of the second section. A general filter design procedure based on the equivalent circuit is presented to assist the design of all-pole filters. Alternatively, it is shown that generalised Chebyshev filters with enhanced selectivity may be developed with cross coupled resonator topologies. The discussions are supplemented with detailed design examples which are accompanied by theoretical, simulated and experimental results in order to illustrate the filter development process and showcase practical filter performance. The third section explores the possibility of employing these resonators in the development of frequency tunable bandpass filters. Preference is given to varactor diodes as the tuning element due to the numerous qualities of this device in contrast to other schemes. In particular, interest is paid to center frequency tuned filters with constant bandwidth. Tunable filters constructed with the dual-mode resonator are shown to have a relatively wide tuning range as well as significantly higher linearity in comparison to similar published works. In line with the previous section, experimental verification is presented to support and supplement the discussions

Advances in Filter Miniaturization and Design/Analysis of RF MEMS Tunable Filters

The main purpose of this dissertation was to address key issues in the design and analysis of RF/microwave filters for wireless applications. Since RF/microwave filters are one of the bulkiest parts of communication systems, their miniaturization is one of the most important technological challenges for the development of compact transceivers. In this work, novel miniaturization techniques were investigated for single-band, dual-band, ultra-wideband and tunable bandpass filters. In single-band filters, the use of cross-shaped fractals in half-mode substrate-integrated-waveguide bandpass filters resulted in a 37 percent size reduction. A compact bandpass filter that occupies an area of 0.315 mm2 is implemented in 90-nm CMOS technology for 20 GHz applications. For dual-band filters, using half-mode substrate-integrated-waveguides resulted in a filter that is six times smaller than its full-mode counterpart. For ultra-wideband filters, using slow-wave capacitively-loaded coplanar-waveguides resulted in a filter with improved stopband performance and frequency notch, while being 25 percent smaller in size. A major part of this work also dealt with the concept of 'hybrid' RF MEMS tunable filters where packaged, off-the-shelf RF MEMS switches were used to implement high-performance tunable filters using substrate-integrated-waveguide technology. These 'hybrid' filters are very easily fabricated compared to current state-of-the-art RF MEMS tunable filters because they do not require a clean-room facility. Both the full-mode and half-mode substrate-integrated waveguide tunable filters reported in this work have the best Q-factors (93 - 132 and 75 - 140, respectively) compared to any 'hybrid' RF MEMS tunable filter reported in current literature. Also, the half-mode substrate-integrated waveguide tunable filter is 2.5 times smaller than its full-mode counterpart while having similar performance. This dissertation also presented detailed analytical and simulation-based studies of nonlinear noise phenomena induced by Brownian motion in all-pole RF MEMS tunable filters. Two independent mathematical methods are proposed to calculate phase noise in RF MEMS tunable filters: (1) pole-perturbation approach, and (2) admittance-approach. These methods are compared to each other and to harmonic balance noise simulations using the CAD-model of the RF MEMS switch. To account for the switch nonlinearity in the mathematical methods, a nonlinear nodal analysis technique for tunable filters is also presented. In summary, it is shown that output signal-to-noise ratio degradation due to Brownian motion is maximum for low fractional bandwidth, high order and high quality factor RF MEMS tunable filters. Finally, a self-sustained microwave platform to detect the dielectric constant of organic liquids is presented in this dissertation. The main idea is to use a voltage- controlled negative-resistance oscillator whose frequency of oscillation varies according to the organic liquid under test. To make the system self-sustained, the oscillator is embedded in a frequency synthesizer system, which is then digitally interfaced to a computer for calculation of dielectric constant. Such a system has potential uses in a variety of applications in medicine, agriculture and pharmaceuticals

Classical and fluctuation-induced electromagnetic interactions in micronscale systems: designer bonding, antibonding, and Casimir forces

Whether intentionally introduced to exert control over particles and macroscopic objects, such as for trapping or cooling, or whether arising from the quantum and thermal fluctuations of charges in otherwise neutral bodies, leading to unwanted stiction between nearby mechanical parts, electromagnetic interactions play a fundamental role in many naturally occurring processes and technologies. In this review, we survey recent progress in the understanding and experimental observation of optomechanical and quantum-fluctuation forces. Although both of these effects arise from exchange of electromagnetic momentum, their dramatically different origins, involving either real or virtual photons, lead to different physical manifestations and design principles. Specifically, we describe recent predictions and measurements of attractive and repulsive optomechanical forces, based on the bonding and antibonding interactions of evanescent waves, as well as predictions of modified and even repulsive Casimir forces between nanostructured bodies. Finally, we discuss the potential impact and interplay of these forces in emerging experimental regimes of micromechanical devices.Comment: Review to appear on the topical issue "Quantum and Hybrid Mechanical Systems" in Annalen der Physi

Reconfigurable Bulk Acoustic Wave Resonators and Filters Employing Electric-field-induced Piezoelectricity and Negative Piezoelectricity for 5G

The ever-expanding wireless communications and sensing are influencing every aspect of human life. With the persistent demand for higher data capacity and recent advancements in wireless technologies, the design of current radio frequency front-end circuitry in communication devices calls for transformative changes. Frequency band proliferation is the biggest contributor to the added RF front-ends complexity in the design of future radios. To operate at various frequency bands, a complex combination of switches and filters is used in mobile devices, and the number of these frequency selective components in each device is expected to exceed 100 with the advent of 5th generation (5G) communication networks. Acoustic wave filters based on piezoelectric materials are the primary technologies employed in current communication systems, including mobile phones. Alternatively, the integration of multifunctional ferroelectric materials into reconfigurable frequency selective components promises reduced complexity, diminished size, and high performance for future radios, enabling them to support 5G wireless technologies and beyond. A promising reconfigurable bulk acoustic wave technology, employing electric-field-induced piezoelectricity and negative piezoelectricity in ferroelectrics, is presented in this dissertation. Successful implementation of ferroelectric filters would eliminate the need for external switcheplexers in the RF front-ends and reduce the number of required filters, leading to a significant reduction in size, cost, and complexity. Contributions of this work are categorized into three major parts. In the first part, an intrinsically switchable thin film bulk acoustic wave resonator (FBAR) based on ferroelectric BST with the highest figure of merit (i.e., Q_m×K_t^2) in the literature is presented. The BST FBARs are then employed to design intrinsically switchable filters with the lowest insertion loss to date. Such filters combine filtering and switching functionalities onto a single device, eliminating the need for external switches in RF front-ends. The second part of this work focuses on the development of frequency and bandwidth reconfigurable filters based on BST FBARs. The first switchless acoustic wave filter bank is presented in chapter 3, demonstrating the capability of BST FBARs in simplifying future agile radios. Next, a novel bandwidth reconfigurable filter based on BST FBARs is introduced in chapter 4, where the idea is experimentally validated with multiple design examples. Finally, through rigorous mathematical analysis and experimental validation, it has been demonstrated that a dynamic ‘non-uniform piezoelectric coefficient’ created within a composite structure made up of multi-layers of ferroelectrics allows the selective excitation of different mechanical Eigenmodes with a constant electromechanical coupling coefficient. Such technology overcomes the fundamental limitations associated with the electromechanical coupling coefficient of harmonic resonances in bulk acoustic wave resonators. To create ‘non-uniform piezoelectric coefficients’ in such structures, ferroelectrics’ electric-field-induced piezoelectricity and negative piezoelectricity has been exploited. This innovative technology provides a fundamentally new approach and a framework for synthesizing programmable frequency selective components, which leads to transformative advances in wireless systems’ front-end architecture. As part of the future direction, it is suggested that the multilayer structure presented in this section to be further studies as part of a new acoustic wave resonator design, which: (a) is capable of operation at a wide frequency range up to mm-wave frequencies designated for 5G (b). Such a structure has the potential to overcome the fundamental limitation of acoustic resonator’s ever-decreasing electromechanical coupling factors (Kt2) as their frequency of operation increases.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/163011/1/milad_1.pd