Delay Measurements and Self Characterisation on FPGAs

This thesis examines new timing measurement methods for self delay characterisation of Field-Programmable Gate Arrays (FPGAs) components and delay measurement of complex circuits on FPGAs. Two novel measurement techniques based on analysis of a circuit's output failure rate and transition probability is proposed for accurate, precise and efficient measurement of propagation delays. The transition probability based method is especially attractive, since it requires no modifications in the circuit-under-test and requires little hardware resources, making it an ideal method for physical delay analysis of FPGA circuits. The relentless advancements in process technology has led to smaller and denser transistors in integrated circuits. While FPGA users benefit from this in terms of increased hardware resources for more complex designs, the actual productivity with FPGA in terms of timing performance (operating frequency, latency and throughput) has lagged behind the potential improvements from the improved technology due to delay variability in FPGA components and the inaccuracy of timing models used in FPGA timing analysis. The ability to measure delay of any arbitrary circuit on FPGA offers many opportunities for on-chip characterisation and physical timing analysis, allowing delay variability to be accurately tracked and variation-aware optimisations to be developed, reducing the productivity gap observed in today's FPGA designs. The measurement techniques are developed into complete self measurement and characterisation platforms in this thesis, demonstrating their practical uses in actual FPGA hardware for cross-chip delay characterisation and accurate delay measurement of both complex combinatorial and sequential circuits, further reinforcing their positions in solving the delay variability problem in FPGAs

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

On-the-fly Computation Method in Field-Programmable Gate Array for Analog-to-Digital Converter Linearity Testing

This paper presents a new approach to linearity testing of analog-to-digital converters (ADCs) through on-the-fly computation in field-programmable gate array (FPGA) hardware. The proposed method computes the linearity while it is processing without compromising the accuracy of the measurement, so very little overhead time is required to compute the final linearity. The results will be displayed immediately after a single ramp is supplied to the device under test. This is a cost-effective chip testing solution for semiconductor companies, achieved by reducing computing time and utilization of low-cost and low-specification automatic test equipment (ATE). The experimental results showed that the on-the-fly computation method significantly reduced the computation time (up to 44.4%) compared to the conventional process. Thus, for every 100M 12-bit ADC tested with 32 hits per code, the company can save up to 139,972 Php on electricity consumption

Phase Locking Authentication for Scan Architecture

Scan design is a widely used Design for Testability (DfT) approach for digital circuits. It provides a high level of controllability and observability resulting in a high fault coverage. To achieve a high level of testability, scan architecture must provide access to the internal nodes of the circuit-under-test (CUT). This access however leads to vulnerability in the security of the CUT. If an unrestricted access is provided through a scan architecture, unlimited test vectors can be applied to the CUT and its responses can be captured. Such an unrestricted access to the CUT can potentially undermine the security of the critical information stored in the CUT. There is a need to secure scan architecture to prevent hardware attacks however a secure solution may limit the CUT testability. There is a trade-off between security and testability, therefore, a secure scan architecture without hindering its controllability and observability is required. Three solutions to secure scan architecture have been proposed in this thesis. In the first method, the tester is authenticated and the number of authentication attempts has been limited. In the second method, a Phase Locked Loop (PLL) is utilized to secure scan architecture. In the third method, the scan architecture is secured through a clock and data recovery (CDR) technique. This is a manuscript based thesis and the results of this study have been published in two conference proceedings. The latest results have also been prepared as an article for submission to a high rank conference

On-the-fly computation method in field-programmable gate array for analog-to-digital converter linearity testing

© 2018 Published by ITB Journal Publisher. This paper presents a new approach to linearity testing of analog-to-digital converters (ADCs) through on-the-fly computation in field-programmable gate array (FPGA) hardware. The proposed method computes the linearity while it is processing without compromising the accuracy of the measurement, so very little overhead time is required to compute the final linearity. The results will be displayed immediately after a single ramp is supplied to the device under test. This is a cost-effective chip testing solution for semiconductor companies, achieved by reducing computing time and utilization of low-cost and low-specification automatic test equipment (ATE). The experimental results showed that the on-the-fly computation method significantly reduced the computation time (up to 44.4%) compared to the conventional process. Thus, for every 100M 12-bit ADC tested with 32 hits per code, the company can save up to 139,972 Php on electricity consumption

Test Strategies for Embedded ADC Cores in a System-on-Chip, A Case Study

Testing of a deeply embedded mixed-signal core in a System-on-Chip (SoC) is a challenging issue due to the communication bottleneck in accessing the core from external automatic test equipment. Consequently, in many cases the preferred approach is built-in self-test (BIST), where the major part of test activity is performed within the unit-under-test and only final results are communicated to the external tester. IEEE Standard 1500 provides efficient test infrastructure for testing digital cores; however, its applications in mixed-signal core test remain an open issue. In this paper we address the problem of implementing BIST of a mixed-signal core in a IEEE Std 1500 test wrapper and discuss advantages and drawbacks of different test strategies. While the case study is focused on histogram based test of ADC, test strategies of other types of mixed-signal cores related to trade-off between performance (i.e., test time) and required resources are likely to follow similar conclusions

Low-overhead fault-tolerant logic for field-programmable gate arrays

While allowing for the fabrication of increasingly complex and efficient circuitry, transistor shrinkage and count-per-device expansion have major downsides: chiefly increased variation, degradation and fault susceptibility. For this reason, design-time consideration of faults will have to be given to increasing numbers of electronic systems in the future to ensure yields, reliabilities and lifetimes remain acceptably high. Many mathematical operators commonly accelerated in hardware are suited to modification resulting in datapath error detection and correction capabilities with far lower area, performance and/or power consumption overheads than those incurred through the utilisation of more established, general-purpose fault tolerance methods such as modular redundancy. Field-programmable gate arrays are uniquely placed to allow further area savings to be made thanks to their dynamic reconfigurability. The majority of the technical work presented within this thesis is based upon a benchmark hardware accelerator---a matrix multiplier---that underwent several evolutions in order to detect and correct faults manifesting along its datapath at runtime. In the first instance, fault detectability in excess of 99% was achieved in return for 7.87% additional area and 45.5% extra latency. In the second, the ability to correct errors caused by those faults was added at the cost of 4.20% more area, while 50.7% of this---and 46.2% of the previously incurred latency overhead---was removed through the introduction of partial reconfiguration in the third. The fourth demonstrates further reductions in both area and performance overheads---of 16.7% and 8.27%, respectively---through systematic data width reduction by allowing errors of less than ±0.5% of the maximum output value to propagate.Open Acces