72 research outputs found
A Novel Flywheel and Operation Approach for Energy Recovery and Storage
Flywheel has intrinsic advantages over other energy storage forms such as hydraulic storage, batteries and compressed airs. These advantages include higher robustness, longer life cycle, great energy density, higher efficiency, lower loss, better discharge depth and relatively easier recycling, etc.
In this dissertation a novel shaftless flywheel was developed. The most important feature of our novel design is the integration of the motor generator and the magnetic suspension into the flywheel disk, which removes the need for a support shaft and enables our solid disk design. This design was shown to have big advantages than traditional designs using annular discs press-fitted on shafts. This was illustrated by a comparison between annular and solid 4340 discs in stress levels, SN lives and fatigue lives with cracks. Due to the scale of the system, our rotating speed is relatively lower than traditional designs. This makes possible the usage of unlaminated magnetic bearings to reduce the system cost at partial expense of the system performance.
A 4340 steel sample was tested to retrieve its magnetic behavior. The novel magnetic levitation was then designed using ANSYS static analysis based on the measured data. The position stiffness and current stiffness were retrieved with the analysis.
The eddy losses of the magnetic bearings were retrieved through FEM motor software CARMENTM by Vector FieldTM. The total bearing loss was calculated based on the simulated eddy loss and measured hysteresis loss on 4340. The system equilibrium temperature was simulated with ANSYSTM.
The Frequency weakening effect of the magnetic bearing was analyzed with ANSYSTM harmonic analysis. The closed-loop control stability of the system was investigated based on the results.
A motor design concept was proposed with the variable motor/generator gain capability. This capability was a key feature in optimizing the charge/discharge performances of the flywheel in both grid level and hybrid locomotive applications.
Based on EPA average data, the benefits of our hybrid locomotives on fuel and NOx savings were simulated on various train operations. The optimization for regenerative braking was also discussed. The dissertation concludes with the discussion of the flywheel system isolation from train operation induced vibrations
Dynamic performance modelling of tidal stream turbines in ocean waves.
The primary aim of this work is to develop a tool to predict the lifetime performance of a tidal stream turbine. This involves the experimental validation of Blade Element Momentum Theory (BEMT) and implementation of an extended model to optimise blade design and predict performance over the operating range. Time varying non-linear upstream flows, such as wave action and velocity gradients are considered and the model is extended into the time domain to obtain the dynamic response of the rotor. In addition, to rationalise the environmental conditions that a device will encounter in its lifetime, representative sea-states and occurrences must be defined. A 1m diameter turbine is tow tested in the River Tawe. It is monitored and controlled such that the performance can be analysed over the operating range. An automated electrical control system is also tested. The results are compared to BEMT. The BEMT is numerically implemented and examined to determine its limitations. Off-optimum performance is considered. The model is extended to incorporate a time dependent flow field with additional velocity and acceleration terms to allow the consideration of wave kinematics. Resultant forces are defined and calculated for particular environmental conditions. Finally the results are interpreted to allow the estimation of lifetime loadings including peak loads and fatigue. The model is validated and a good correlation is found relative to standard BEMT. It is concluded that both a velocity gradient and a wave action may significantly reduce power output whilst increasing the loads on a system. It is also concluded that a 3 bladed rotor encounters far lower loadings than a 2 bladed equivalent over the device lifetime. It is also the intention of this study to compare and contrast various tidal stream turbine support structure concepts in terms of the suitability of each to withstand the lifetime loadings at reasonable cost. A number of support structure concepts are investigated from an impartial perspective. In conclusion there is not one concept which clearly surpasses the others in all areas
Understanding and modelling damage and fracture in nuclear grade graphite
This thesis studied the crack initiation and propagation characteristics of Nuclear Block Graphite 10 (NBG10) and Gilsocarbon (IM1-24), using the DoubleTorsion (DT) technique
Tidal turbine modelling from the perspective of design and operation
The aim of this thesis is to study the effects of turbulent flow on a fixed pitch
tidal current turbine from the perspective of turbine design and operation. A
prototype turbine, Deltastream as it is known, is being developed by Tidal
Energy Ltd for deployment in Ramsey Sound, Wales. It is well known that
turbulence plays an important role in the fatigue life of marine turbines. Field
measurements of tidal flow at the turbine site were analysed to establish the
velocity spectra and turbulence intensity. This revealed a wide range of
anisotropic turbulence which is dependent upon the tidal direction with
intensities ranging from 5-20%.
A numerical turbine model based on momentum theory was constructed in a
time marching formulation that accounts for the effects of dynamic inflow and
rotationally augmented airfoil stall delay properties. The turbine rotor design
allows for load alleviation by regulation of the turbine tip speed ratio. At flow
velocities above the rated velocity the tip speed ratio can be increased to
reduce turbine loads. The model has been combined with a novel rotor speed
control algorithm that estimates unsteady turbine inflow velocity from turbine
loading without the requirement for external sensing of flow speed. When the
turbine is subjected to three dimensional turbulent inflow the rotor speed
controller has been shown to significantly reduce the fatigue effect of unsteady,
turbulent flow. The turbine blade design has been developed using the model
established. Experimental validation studies were carried out at 1/16th scale in
turbulent conditions.
Studies using the model have; identified the relationship between turbulence
intensity and turbine fatigue load, established a controller schedule to
significantly reduce fatigue loading and determined the blading fatigue life in
realistic turbulent flows
Investigation of all-wheel-drive off-road vehicle dynamics augmented by visco-lock devices
A peculiarity of AWD off-road vehicles is that their behaviour depends not only on the
total power, provided by the engine, but also on its distribution among the drive
axles/wheels. In turn, this distribution is largely regulated by the drivetrain layout and its
torque distribution devices. At the output of the drivetrain system, the torque is
constrained by the interaction between the wheels and the soft soil. For off-road
automotive applications, the design of drivetrain systems has usually been largely
dominated by the mobility requirements. With the growing demand to have a multipurpose
on/off road vehicle with improved manoeuvrability over deformable soil,
particularly at higher speed, the challenges confronting vehicle designers have become
more complex.
The thesis presents a novel integrated numerical approach to assess the dynamic
behaviour of all-wheel-drive vehicles whilst operating over deformable soil terrain. [Continues.
Axisymmetry in Mechanical Engineering
The reprint is devoted to the phenomena associated with exact or approximate axial symmetry in different areas of technical physics and mechanical engineering science. How can the symmetry of the problem be used most efficiently for its analysis? Why is the symmetry broken or why is it still approximately retained? These and other questions are discussed based on systems from different fields of engineering
The experimental determination of the viscosity of steam at high pressure
Abstract not available
Advances in Vibration Analysis Research
Vibrations are extremely important in all areas of human activities, for all sciences, technologies and industrial applications. Sometimes these Vibrations are useful but other times they are undesirable. In any case, understanding and analysis of vibrations are crucial. This book reports on the state of the art research and development findings on this very broad matter through 22 original and innovative research studies exhibiting various investigation directions. The present book is a result of contributions of experts from international scientific community working in different aspects of vibration analysis. The text is addressed not only to researchers, but also to professional engineers, students and other experts in a variety of disciplines, both academic and industrial seeking to gain a better understanding of what has been done in the field recently, and what kind of open problems are in this area
Proceedings of the ECCOMAS Thematic Conference on Multibody Dynamics 2015
This volume contains the full papers accepted for presentation at the ECCOMAS Thematic Conference on Multibody Dynamics 2015 held in the Barcelona School of Industrial Engineering, Universitat Politècnica de Catalunya, on June 29 - July 2, 2015. The ECCOMAS Thematic Conference on Multibody Dynamics is an international meeting held once every two years in a European country. Continuing the very successful series of past conferences that have been organized in Lisbon (2003), Madrid (2005), Milan (2007), Warsaw (2009), Brussels (2011) and Zagreb (2013); this edition will once again serve as a meeting point for the international researchers, scientists and experts from academia, research laboratories and industry working in the area of multibody dynamics. Applications are related to many fields of contemporary engineering, such as vehicle and railway systems, aeronautical and space vehicles, robotic manipulators, mechatronic and autonomous systems, smart structures, biomechanical systems and nanotechnologies. The topics of the conference include, but are not restricted to: ● Formulations and Numerical Methods ● Efficient Methods and Real-Time Applications ● Flexible Multibody Dynamics ● Contact Dynamics and Constraints ● Multiphysics and Coupled Problems ● Control and Optimization ● Software Development and Computer Technology ● Aerospace and Maritime Applications ● Biomechanics ● Railroad Vehicle Dynamics ● Road Vehicle Dynamics ● Robotics ● Benchmark ProblemsPostprint (published version
Proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress
Published proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress, hosted by York University, 27-30 May 2018
- …