111 research outputs found

    Testing a CMOS operational amplifier circuit using a combination of oscillation and IDDQ test methods

    Get PDF
    This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. The approach is attractive for its simplicity, robustness and capability of built-in-self test (BIST) implementation. It can also be generalized to the oscillation based test structures of other CMOS analog and mixed-signal integrated circuits. The practical results and simulations confirm the functionality of the proposed test method

    A design for testability study on a high performance automatic gain control circuit.

    Get PDF
    A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

    IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling ADC

    Get PDF
    This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on Altera\u27s FLEXE20K board using Verilog. The modulator and decimator were assembled together to form a sigma-delta ADC

    Quiescent current testing of CMOS data converters

    Get PDF
    Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

    Programmable CMOS Analog-to-Digital Converter Design and Testability

    Get PDF
    In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation

    Power supply current [IPS] based testing of CMOS amplifier circuit with and without floating gate input transistors

    Get PDF
    This work presents a case study, which attempts to improve the fault diagnosis and testability of the power supply current based testing methodology applied to a typical two-stage CMOS operational amplifier and is extended to operational amplifier with floating gate input transistors*. The proposed test method takes the advantage of good fault coverage through the use of a simple power supply current measurement based test technique, which only needs an ac input stimulus at the input and no additional circuitry. The faults simulating possible manufacturing defects have been introduced using the fault injection transistors. In the present work, variations of ac ripple in the power supply current IPS, passing through VDD under the application of an ac input stimulus is measured to detect injected faults in the CMOS amplifier. The effect of parametric variation is taken into consideration by setting tolerance limit of ± 5% on the fault-free IPS value. The fault is identified if the power supply current, IPS falls outside the deviation given by the tolerance limit. This method presented can also be generalized to the test structures of other floating-gate MOS analog and mixed signal integrated circuits

    Variance reduction and outlier identification for IDDQ testing of integrated chips using principal component analysis

    Get PDF
    Integrated circuits manufactured in current technology consist of millions of transistors with dimensions shrinking into the nanometer range. These small transistors have quiescent (leakage) currents that are increasingly sensitive to process variations, which have increased the variation in good-chip quiescent current and consequently reduced the effectiveness of IDDQ testing. This research proposes the use of a multivariate statistical technique known as principal component analysis for the purpose of variance reduction. Outlier analysis is applied to the reduced leakage current values as well as the good chip leakage current estimate, to identify defective chips. The proposed idea is evaluated using IDDQ values from multiple wafers of an industrial chip fabricated in 130 nm technology. It is shown that the proposed method achieves significant variance reduction and identifies many outliers that escape identification by other established techniques. For example, it identifies many of the absolute outliers in bad neighborhoods, which are not detected by Nearest Neighbor Residual and Nearest Current Ratio. It also identifies many of the spatial outliers that pass when using Current Ratio. The proposed method also identifies both active and passive defects

    A CURRENT TO DIGITAL CONVERTER FOR POWER SIGNATURE GENERATION APPLICATIONS

    Get PDF
    The security of IoT devices is significantly increasing as a consequence of the widespread usage of the Internet of Things (IoT) in applications that include confidential data and implementation of important control decisions using those data. Because of their cheap cost and computational limitations, IoT devices confront significant obstacles in safeguarding. Among the variety of devised tactics analyzing power is one of the most potential strategies to address such challenges. However, due to the size, cost, and power consumption of power analysis devices, this strategy is not suited for many IoT applications. In this thesis, two techniques for collecting power signatures were proposed. A commercial 130nm CMOS technology is used to construct two circuits for each technique. For the purpose of determining how correctly the setups function, a considerable number of simulations are run under various conditions, and the results are assessed

    Design-for-Test of Mixed-Signal Integrated Circuits

    Get PDF
    • …
    corecore