On-line Testing Field Programmable Analog Array Circuits

This work presents an efficient methodology to on-line test field programmable analog array (FPAA) circuits. It proposes to partition the FPAA circuit under test into sub circuits. Each sub circuit is tested by replicating the sub circuit with programmable resources on FPAAs, and comparing the outputs of the original partitioned sub circuit and its replication. The advantages of this approach includes: low implementation cost, enhanced testability, and flexible testing schedules. This work also presents circuit techniques to address stability problems which are often encountered in the proposed on-line testing approach. In addition, the impact of performing circuit partition on testability is investigated in this work. It shows that testability is generally improved in partitioned circuits. Finally, experimental results are presented to demonstrate the feasibility and effectiveness of the proposed techniques

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

On Flip-Flop Selection for Multi-cycle Scan Test with Partial Observation in Logic BIST

Multi-cycle test with partial observation for scan-based logic BIST is known as one of effective methods to improve fault coverage without increase of test time. In the method, the selection of flip-flops for partial observation is critical to achieve high fault coverage with small area overhead. This paper proposes a selection method under the limitation to a number of flip-flops. The method consists of structural analysis of CUT and logic simulation of test vectors, therefore, it provides an easy implementation and a good scalability. Experimental results on benchmark circuits show that the method obtains higher fault coverage with less area overhead than the original method. Also the relation between the number of selected flip-flops and fault coverage is investigated.27th IEEE ASIAN TEST SYMPOSIUM (ATS\u2718), 15-18 October 2018, Hefei, Chin

Built-In Self-Test (BIST) for Multi-Threshold NULL Convention Logic (MTNCL) Circuits

This dissertation proposes a Built-In Self-Test (BIST) hardware implementation for Multi-Threshold NULL Convention Logic (MTNCL) circuits. Two different methods are proposed: an area-optimized topology that requires minimal area overhead, and a test-performance-optimized topology that utilizes parallelism and internal hardware to reduce the overall test time through additional controllability points. Furthermore, an automated software flow is proposed to insert, simulate, and analyze an input MTNCL netlist to obtain a desired fault coverage, if possible, through iterative digital and fault simulations. The proposed automated flow is capable of producing both area-optimized and test-performance-optimized BIST circuits and scripts for digital and fault simulation using commercial software that may be utilized to manually verify or adjust further, if desired

Ensuring a High Quality Digital Device through Design for Testability

An electronic device is reliable if it is available for use most of the times throughout its life. The reliability can be affected by mishandling and use under abnormal operating conditions. High quality product cannot be achieved without proper verification and testing during the product development cycle. If the design is difficult to test, then it is very likely that most of the faults will not be detected before it is shipped to the customer. This paper describes how product quality can be improved by making the hardware design testable. Various designs for testability techniqueswere discussed. A three bit counter circuit was used to illustrate the benefits of design for testability by using scan chain methodology

Design for Test and Hardware Security Utilizing Tester Authentication Techniques

Design-for-Test (DFT) techniques have been developed to improve testability of integrated circuits. Among the known DFT techniques, scan-based testing is considered an efficient solution for digital circuits. However, scan architecture can be exploited to launch a side channel attack. Scan chains can be used to access a cryptographic core inside a system-on-chip to extract critical information such as a private encryption key. For a scan enabled chip, if an attacker is given unlimited access to apply all sorts of inputs to the Circuit-Under-Test (CUT) and observe the outputs, the probability of gaining access to critical information increases. In this thesis, solutions are presented to improve hardware security and protect them against attacks using scan architecture. A solution based on tester authentication is presented in which, the CUT requests the tester to provide a secret code for authentication. The tester authentication circuit limits the access to the scan architecture to known testers. Moreover, in the proposed solution the number of attempts to apply test vectors and observe the results through the scan architecture is limited to make brute-force attacks practically impossible. A tester authentication utilizing a Phase Locked Loop (PLL) to encrypt the operating frequency of both DUT/Tester has also been presented. In this method, the access to the critical security circuits such as crypto-cores are not granted in the test mode. Instead, a built-in self-test method is used in the test mode to protect the circuit against scan-based attacks. Security for new generation of three-dimensional (3D) integrated circuits has been investigated through 3D simulations COMSOL Multiphysics environment. It is shown that the process of wafer thinning for 3D stacked IC integration reduces the leakage current which increases the chip security against side-channel attacks

Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours

In-flight maintenance study Final report

Sample system analysis, MF requirements, redesign, and packaging desig

On-Line Dependability Enhancement of Multiprocessor SoCs by Resource Management

This paper describes a new approach towards dependable design of homogeneous multi-processor SoCs in an example satellite-navigation application. First, the NoC dependability is functionally verified via embedded software. Then the Xentium processor tiles are periodically verified via on-line self-testing techniques, by using a new IIP Dependability Manager. Based on the Dependability Manager results, faulty tiles are electronically excluded and replaced by fault-free spare tiles via on-line resource management. This integrated approach enables fast electronic fault detection/diagnosis and repair, and hence a high system availability. The dependability application runs in parallel with the actual application, resulting in a very dependable system. All parts have been verified by simulation