Testing for delay defects utilizing test data compression techniques

textAs technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of smaller delay defects; these defects can cause functional behavior to fail and also indicate potential reliability issues. The first part of this dissertation addresses these problems by presenting an enhanced timing-based delay fault testing technique that incorporates the use of standard delay ATPG, along with timing information gathered from standard static timing analysis. Utilizing delay fault patterns typically increases the test data volume by 3-5X when compared to stuck-at patterns. Combined with the increase in test data volume associated with the increase in gate count that typically accompanies the miniaturization of technology, this adds up to a very large increase in test data volume that directly affect test time and thus the manufacturing cost. The second part of this dissertation presents a technique for improving test compression and reducing test data volume by using multiple expansion ratios while determining the configuration of the scan chains for each of the expansion ratios using a dependency analysis procedure that accounts for structural dependencies as well as free variable dependencies to improve the probability of detecting faults. Finally, this dissertation addresses the problem of unknown values (X’s) in the output response data corrupting the data and degrading the performance of the output response compactor and thus the overall amount of test compression. Four techniques are presented that focus on handling response data with large percentages of X’s. The first uses X-canceling MISR architecture that is based on deterministically observing scan cells, and the second is a hybrid approach that combines a simple X-masking scheme with the X-canceling MISR for further gains in test compression. The third and fourth techniques revolve around reiterative LFSR X-masking, which take advantage of LFSR-encoded masks that can be reused for multiple scan slices in novel ways.Electrical and Computer Engineerin

Transition Faults and Transition Path Delay Faults: Test Generation, Path Selection, and Built-In Generation of Functional Broadside Tests

As the clock frequency and complexity of digital integrated circuits increase rapidly, delay testing is indispensable to guarantee the correct timing behavior of the circuits. In this dissertation, we describe methods developed for three aspects of delay testing in scan-based circuits: test generation, path selection and built-in test generation. We first describe a deterministic broadside test generation procedure for a path delay fault model named the transition path delay fault model, which captures both large and small delay defects. Under this fault model, a path delay fault is detected only if all the individual transition faults along the path are detected by the same test. To reduce the complexity of test generation, sub-procedures with low complexity are applied before a complete branch-and-bound procedure. Next, we describe a method based on static timing analysis to select critical paths for test generation. Logic conditions that are necessary for detecting a path delay fault are considered to refine the accuracy of static timing analysis, using input necessary assignments. Input necessary assignments are input values that must be assigned to detect a fault. The method calculates more accurate path delays, selects paths that are critical during test application, and identifies undetectable path delay faults. These two methods are applicable to off-line test generation. For large circuits with high complexity and frequency, built-in test generation is a cost-effective method for delay testing. For a circuit that is embedded in a larger design, we developed a method for built-in generation of functional broadside tests to avoid excessive power dissipation during test application and the overtesting of delay faults, taking the functional constraints on the primary input sequences of the circuit into consideration. Functional broadside tests are scan-based two-pattern tests for delay faults that create functional operation conditions during test application. To avoid the potential fault coverage loss due to the exclusive use of functional broadside tests, we also developed an optional DFT method based on state holding to improve fault coverage. High delay fault coverage can be achieved by the developed method for benchmark circuits using simple hardware

Efficient Path Delay Test Generation with Boolean Satisfiability

This dissertation focuses on improving the accuracy and efficiency of path delay test generation using a Boolean satisfiability (SAT) solver. As part of this research, one of the most commonly used SAT solvers, MiniSat, was integrated into the path delay test generator CodGen. A mixed structural-functional approach was implemented in CodGen where longest paths were detected using the K Longest Path Per Gate (KLPG) algorithm and path justification and dynamic compaction were handled with the SAT solver. Advanced techniques were implemented in CodGen to further speed up the performance of SAT based path delay test generation using the knowledge of the circuit structure. SAT solvers are inherently circuit structure unaware, and significant speedup can be availed if structure information of the circuit is provided to the SAT solver. The advanced techniques explored include: Dynamic SAT Solving (DSS), Circuit Observability Don’t Care (Cir-ODC), SAT based static learning, dynamic learnt clause management and Approximate Observability Don’t Care (ACODC). Both ISCAS 89 and ITC 99 benchmarks as well as industrial circuits were used to demonstrate that the performance of CodGen was significantly improved with MiniSat and the use of circuit structure

VLSI Testing and Test Power

This paper first reviews the basics of VLSI testing, focusing on test generation and design for testability. Then it discusses the impact of test power in scan testing, and highlights the need for low-power VLSI testing.2011 International Green Computing Conference and Workshops (IGCC 2011), July 25-28, 2011, Orlando, FL, US

Optimizing Test Pattern Generation Using Top-Off ATPG Methodology for Stuck–AT, Transition and Small Delay Defect Faults

The ever increasing complexity and size of digital circuits complemented by Deep Sub Micron (DSM) technology trends today pose challenges to the efficient Design For Test (DFT) methodologies. Innovation is required not only in designing the digital circuits, but also in automatic test pattern generation (ATPG) to ensure that the pattern set screens all the targeted faults while still complying with the Automatic Test Equipment (ATE) memory constraints. DSM technology trends push the requirements of ATPG to not only include the conventional static defects but also to include test patterns for dynamic defects. The current industry practices consider test pattern generation for transition faults to screen dynamic defects. It has been observed that just screening for transition faults alone is not sufficient in light of the continuing DSM technology trends. Shrinking technology nodes have pushed DFT engineers to include Small Delay Defect (SDD) test patterns in the production flow. The current industry standard ATPG tools are evolving and SDD ATPG is not the most economical option in terms of both test generation CPU time and pattern volume. New techniques must be explored in order to ensure that a quality test pattern set can be generated which includes patterns for stuck-at, transition and SDD faults, all the while ensuring that the pattern volume remains economical. This thesis explores the use of a “Top-Off” ATPG methodology to generate an optimal test pattern set which can effectively screen the required fault models while containing the pattern volume within a reasonable limit

Optimization of Pseudo Functional Path Delay Test Through Embedded Memories

Traditional automatic test pattern generation achieves high coverage of logic faults in integrated circuits. Automatic test of embedded memory arrays uses built-in self-test. Testing the memories and logic separately does not fully test the critical timing paths that go into or out of memories. Prior research has developed algorithms and software to test the longest paths into and out of embedded memories. However, in this prior work, the test generation time increased superlinearly with memory size. This is contrary to the intuition that the time should rise approximately linearly with memory size. This behavior limits the algorithm to circuits with relatively small memories. The focus of this research is to analyze the time complexity of the algorithm and propose changes to reduce the time required to test circuits with large memories. We use our prior work on pseudo functional K longest path per gate test generation, and the benchmark circuits with embedded memories developed in the prior work. Since the cells within a memory array are not scan cells, a value that is captured in a memory cell must be moved to a scan cell using low-speed coda cycles. This approach will also support the test of any non-scan flip-flop or latch, in addition to embedded memory arrays. In addition to testing the critical timing paths, testing through memories eliminates the logic “shadows” around the memory where faults cannot be tested. In this research our complexity analysis has identified the reason for the superlinear increase in test generation time with larger memories and verified this analysis with experimental results. We have also developed and implemented several heuristics to increase performance, with experimental results. This research also identifies the major algorithm changes required to further increase performance