The SwarmItFix Pilot

Abstract The paper presents the integration and experiments with a pilot cell including a traditional machine tool and an innovative robot-swarm cooperative conformable support for aircraft body panels. The pilot was installed and tested in the premises of the aircraft manufacturer Piaggio Aerospace in Italy. An original approach to the support of the panels is realized: robots with soft heads operate from below the panel; they move upward the panel where manufacturing is performed, removing the sagging under gravity and returning it to its nominal geometry; the spindle of amilling machine performs the machining from above

From 3D Models to 3D Prints: an Overview of the Processing Pipeline

Due to the wide diffusion of 3D printing technologies, geometric algorithms for Additive Manufacturing are being invented at an impressive speed. Each single step, in particular along the Process Planning pipeline, can now count on dozens of methods that prepare the 3D model for fabrication, while analysing and optimizing geometry and machine instructions for various objectives. This report provides a classification of this huge state of the art, and elicits the relation between each single algorithm and a list of desirable objectives during Process Planning. The objectives themselves are listed and discussed, along with possible needs for tradeoffs. Additive Manufacturing technologies are broadly categorized to explicitly relate classes of devices and supported features. Finally, this report offers an analysis of the state of the art while discussing open and challenging problems from both an academic and an industrial perspective.Comment: European Union (EU); Horizon 2020; H2020-FoF-2015; RIA - Research and Innovation action; Grant agreement N. 68044

Design of ultraprecision machine tools with application to manufacturing of miniature and micro components

Currently the underlying necessities for predictability, producibility and productivity remain big issues in ultraprecision machining of miniature/microproducts. The demand on rapid and economic fabrication of miniature/microproducts with complex shapes has also made new challenges for ultraprecision machine tool design. In this paper the design for an ultraprecision machine tool is introduced by describing its key machine elements and machine tool design procedures. The focus is on the review and assessment of the state-of-the-art ultraprecision machining tools. It also illustrates the application promise of miniature/microproducts. The trends on machine tool development, tooling, workpiece material and machining processes are pointed out

Virtual manufacturing: prediction of work piece geometric quality by considering machine and set-up

Lien vers la version éditeur: http://www.tandfonline.com/doi/full/10.1080/0951192X.2011.569952#.U4yZIHeqP3UIn the context of concurrent engineering, the design of the parts, the production planning and the manufacturing facility must be considered simultaneously. The design and development cycle can thus be reduced as manufacturing constraints are taken into account as early as possible. Thus, the design phase takes into account the manufacturing constraints as the customer requirements; more these constraints must not restrict the creativity of design. Also to facilitate the choice of the most suitable system for a specific process, Virtual Manufacturing is supplemented with developments of numerical computations (Altintas et al. 2005, Bianchi et al. 1996) in order to compare at low cost several solutions developed with several hypothesis without manufacturing of prototypes. In this context, the authors want to predict the work piece geometric more accurately by considering machine defects and work piece set-up, through the use of process simulation. A particular case study based on a 3 axis milling machine will be used here to illustrate the authors’ point of view. This study focuses on the following geometric defects: machine geometric errors, work piece positioning errors due to fixture system and part accuracy

Hierarchical control of complex manufacturing processes

The need for changing the control objective during the process has been reported in many systems in manufacturing, robotics, etc. However, not many works have been devoted to systematically investigating the proper strategies for these types of problems. In this dissertation, two approaches to such problems have been suggested for fast varying systems. The first approach, addresses problems where some of the objectives are statically related to the states of the systems. Hierarchical Optimal Control was proposed to simplify the nonlinearity caused by adding the statically related objectives into control problem. The proposed method was implemented for contour-position control of motion systems as well as force-position control of end milling processes. It was shown for a motion control system, when contour tracking is important, the controller can reduce the contour error even when the axial control signals are saturating. Also, for end milling processes it was shown that during machining sharp edges where, excessive cutting forces can cause tool breakage, by using the proposed controller, force can be bounded without sacrificing the position tracking performance. The second approach that was proposed (Hierarchical Model Predictive Control), addressed the problems where all the objectives are dynamically related. In this method neural network approximation methods were used to convert a nonlinear optimization problem into an explicit form which is feasible for real time implementation. This method was implemented for force-velocity control of ram based freeform extrusion fabrication of ceramics. Excellent extrusion results were achieved with the proposed method showing excellent performance for different changes in control objective during the process --Abstract, page iv

Multiresolution analysis as an approach for tool path planning in NC machining

Wavelets permit multiresolution analysis of curves and surfaces. A complex curve can be decomposed using wavelet theory into lower resolution curves. The low-resolution (coarse) curves are similar to rough-cuts and high-resolution (fine) curves to finish-cuts in numerical controlled (NC) machining.;In this project, we investigate the applicability of multiresolution analysis using B-spline wavelets to NC machining of contoured 2D objects. High-resolution curves are used close to the object boundary similar to conventional offsetting, while lower resolution curves, straight lines and circular arcs are used farther away from the object boundary.;Experimental results indicate that wavelet-based multiresolution tool path planning improves machining efficiency. Tool path length is reduced, sharp corners are smoothed out thereby reducing uncut areas and larger tools can be selected for rough-cuts

Assistive control for non-contact machining of random shaped contours

Recent achievements in robotics and automation technology has opened the door towards different machining methodologies based on material removal. Considering the non force feedback nature of non-contact machining methods, careful attention on motion control design is a primary requirement for successful achievement of precise cutting both in machining and in surgery processes. This thesis is concerned with the design of pre-processing methods and motion control techniques to provide both automated and human-assistive non-contact machining of random and complex shaped contours. In that sense, the first part of the thesis focuses on extraction of contours and generation of reference trajectories or constraints for the machining system. Based on generated trajectories, two different control schemes are utilized for high precision automated machining. In the first scheme, preview control is adopted for enhancing the tracking performance. In the second scheme, control action is generated based on direct computation of contouring error in the operational space by introducing a new coordinate frame moving with the reference contour. Further, non-contact machining is extended for realization in a master/slave telerobotic framework to enable manual remote cutting by a human operator. With the proposed approach, the human operator (i.e. a surgeon) is limited to conduct motion within a desired virtual constraint and is equipped with the ability of adjusting the cutting depth over a that contour providing advantage for laser surgery applications. The proposed framework is experimentally tested and results of the experiments prove the applicability of proposed motion control schemes and show the validity of contributions made in the context of thesis

Reliability Analysis of On-Demand High-Speed Machining

Current trends in high-speed machining aim to increase manufacturing efficiency by maximizing material removal rates and minimizing part cycle times. This project explores three related technologies and presents a system design for rapid production of custom machined parts. First a reliability analysis in high-speed machining of thin wall features is put forth with experimental results. Second an implementation of on-demand manufacturing is presented with emphasis on flexibility and automation. Finally innovative manufacturing cell design is used to drive costs down by optimizing material and information flow. The resulting high-speed on-demand machining cell design employs effective techniques to reduce production time, meet changing customer needs, and drive down costs

Flexible manufacturing system utilizing computer integrated control and modeling

In today\u27s fast-automated production, Flexible Manufacturing Systems (FMS) play a very important role by processing a variety of different types of workpieces simultaneously. This study provides valuable information about existing FMS workcells and brings to light a unique concept called Programmable Automation. Another integrated concept of programmable automation that is discussed is the use of two feasibility approaches towards modeling and controlling FMS operations; the most commonly used is programmable logic controllers (PLC), and the other one, which has not yet implemented in many industrial applications is Petri Net controllers (PN). This latter method is a unique powerful technique to study and analyze any production line or any facility, and it can be used in many other applications of automatic control. Programmable Automation uses a processor in conventional metal working machines to perform certain tasks through program instructions. Drilling, milling and chamfering machines are good examples for such automation. Keeping the above issues in concem; this research focuses on other core components that are used in the FMS workcell at New Jersey Institute of Technology, such as; industrial robots, material handling system and finally computer vision

Practical Development Of An Open Architecture Personal Computer-Based Numerical Control (Oapc-Nc) System [TJ1189. P535 2005 f rb].

In this research, an open architecture personal computer-based numerical control (OAPC-NC) system that can generate G-code was developed. Dalam pengajian ini, satu sistem kawalan berarkitektur terbuka berdasarkan komputer perseorangan (OAPC-NC) yang dapat menjalankan kod kawalan berangka telah dicipta