A Passive UHF RFID System over Ethernet Cable for Long Range Detection

This paper proposes a new form of passive UHF RFID system which has high tag detection accuracy but lower costs than existing systems for wide-range RFID scenarios requiring greater flexibility. This new system concept consists of a central baseband controller and a remote antenna subsystem, connected using a twisted-pair cable. Baseband signals are transmitted over the twisted-pair cable during the inventory session, and the transmitted radio frequency (RF) signals are up and down converted in the antenna subsystem. – 88 dBm reader sensitivity is achieved with an active leakage cancellation block, showing little degradation in tag detection performance over a 300m of Cat5e cable between the controller and the antenna. An average leakage suppression of 36.9 dB can be achieved with a fixed transmission power of 26.5 dBm. Compared with conventional RFID systems using coaxial cables between the reader and antenna, the presented system is superior in terms of link distance, link cost, and installation flexibility

RFID multiantenna systems for wireless communications and sensing

Many scientific, industrial and medical applications require the measurement of different physical parameters in order to collect information about the spatially distributed status of some process. Very often this information needs to be collected remotely, either due to the spatial dispersion of the measurement points or due to their inaccessibility. A wireless embedded self-powered sensor may be a convenient solution to be placed at these inaccessible locations. This thesis is devoted to study the analytical relation governing the electromagnetic coupling between a reader and a embeddable self-powered sensor, based on radio frequency identification (RFID) technology, which is capable of wirelessly retrieving the status of physical parameters at a remote and inaccessible location. The physical parameter to be sensed may be the electromagnetic (EM) field existing at that location (primary measurement) or the indirect measurement of other parameters such as the temperature, humidity, etc. (secondary measurement). Given the simplicity of the RFID solution (highly embeddable properties, scavenging capabilities, penetration and radio coverage characteristics, etc.) the measurement can be done at a single location, or it can be extended to a set of measuring locations (an array or grid of sensors). The analytical relation is based on a reciprocity formulation studying the modulation of the scattered field by the embedded sensor in relation with the incident field, and allows to define a set of quality parameters of interest for the optimum design of the sensors. Particular attention is given to the scavenging circuitry as well as to the antenna design relevant to the sensing objective. In RFID tags, the existence of an RF harvesting section is an improvement with respect to conventional scattering field probes since it removes the need of DC biasing lines or optical fibers to modulate the sensor. However, this harvesting section introduces non-linearities in the response of the sensor, which requires a proper correction to use them as EM-field probes, although the characterization of the non-linearities of the RFID tag cannot be directly done using a conventional vector network analyzer (VNA), due to the requirements of an RFID protocol excitation. Due to this, this thesis proposes an alternative measurement approach that allows to characterize the different scattering states used for the modulation, in particular its non-linear behavior. In addittion, and taking this characterization as the starting point, this thesis proposes a new measurement setup for EM-field measurements based on the use of multiple tones to enlarge the available dynamic range, which is experimentally demonstrated in the measurement of a radiation pattern, as well as in imaging applications. The RFID-based sensor response is electromagnetically sensitive to the dielectric properties of its close environment. However, the governing formulation for the response of the probe mixes together a set of different contributions, the path-loss, the antenna impedance, the loads impedance, etc. As a consequence, it is not possible to isolate each contribution from the others using the information available with a conventional RFID sensor. This thesis mathematically proposes and experimentally develops a modification of the modulation scheme to introduce a new set of multi-load scattering states that increases the information available in the response and properly isolate each term. Moreover, this thesis goes a step forward and introduces a new scattering state of the probe sensitive to temperature variations that do not depend on the environment characteristics. This new configuration enables robust environmental sensing in addition to EM-field measurements, and sensing variations of the dielectric properties of the environment

Backscatter Communication: Design and Optimisation For Emerging Use-Cases

Backscatter communication (BackCom) holds significant potential to improve the pervasiveness and energy efficiency of future wireless networks, through its passive modulation and reuse of existing radiofrequency signals. In order to function as a key technology under the Internet of Things paradigm, issues relating to BackCom, such as its limited coverage and deployment flexibility, low data rates, and the difficulty of channel estimation, need to be addressed. To complement this, a wider range of use-cases and deployment scenarios also need to be established. This thesis focuses on addressing these issues inherent to BackCom, by exploring a series of system setups which push the boundaries in terms of coverage and flexible deployment, and then future-proofs BackCom through the study of the assistance from another emerging technology, the intelligent reflecting surface (IRS). The first half of the thesis focuses on the coverage and deployment flexibility of BackCom devices under conventional wireless communication settings. First, we study a novel use-case in which BackCom devices replace conventional, actively transmitting relays to assist an information transmission from a source to a destination. We introduce the decode-and-forward (DF) BackCom relaying scheme and perform a detailed bit error rate (BER) characterisation of the DF BackCom scheme alongside the amplify-and-forward (AF) BackCom 'reflection' scheme. The feasibility and practical range of the BackCom relay is demonstrated through a case study, and our findings indicate that with careful selection of relay parameters, the DF scheme can improve the functionality of BackCom relays through the decoding operation, while resulting in minimal BER differences compared to the AF 'reflection' scheme. Second, we study the coverage maximisation of bistatic BackCom systems in wide-area environmental monitoring applications through judicious power beacon (PB) placement. We propose a straightforward metric to characterise coverage, the guaranteed coverage distance (GCD), to overcome the complex shape of each PB's coverage area when the performance of the BackCom link is dependent on the strength of the energy transfer link. We find that a single-tier symmetric deployment of PBs performs favourably under a practical number (24 or less) of PBs, with a GCD of more than 100m being readily achievable. The second half of the thesis studies the incorporation of the IRS into BackCom systems, with the aim of improving BackCom performance. The IRS-assisted bistatic BackCom system is studied first, where we solve a transmit power minimisation problem at the carrier emitter involving the joint optimisation of the transmit and receive beamforming, the IRS phase shifts and the BackCom splitting coefficients. We present a unique signal model arising from this system, where a signal originating from the carrier emitter may be reflected by the IRS twice before reaching the reader, and account for this added complexity in our algorithm design. Our results indicate that transmit power savings of over 6 dB may be achieved with a moderately-sized IRS, which may be converted to nearly 50m of range increase. Then, we study the use of the IRS in an ambient BackCom system, with the goal of reducing direct-link interference and improving detection performance. We assume the absence of all ambient signal and channel knowledge, which is a practical assumption given the passively reflecting nature of both BackCom devices and IRSs. We propose a deep reinforcement learning (DRL)-based algorithm which maximises the backscatter channel difference (that is, the ratio of the energies of the direct-link interference and overall received signal) based on instantaneous signal samples, which may be converted to BER reductions. We find that the DRL approach with no channel knowledge can achieve a backscatter channel difference within 25% of that obtained using benchmarks with full channel knowledge

Signal Processing for Wireless Power and Information Transfer

The rapid development of the Internet of Things (IoT) and wireless sensor network (WSN) technologies enable easy access and control of a variety forms of information and data from numerous number of smart devices, and give rise to many novel applications and research areas such as smart home, machine type communications, etc. However due to the small sizes, sophisticated environment, and large number of devices in network, it is hard to directly power the devices from grid. Hence the power connectivity remains one of the major issues that needs to be addressed for related IoT applications. Wireless power transfer (WPT) and backscatter communications are provisioned to be prominent solutions to overcome the power connectivity challenge, but they suer strong efficiency limitation which becomes the barrier to universally popularize such technologies. On the other hand, network optimization is also a research focus of such applications which significantly affects the performance of the system due to the high volume of connected devices and different features. In this thesis we propose advanced techniques to overcome the challenges on the low efficiency and network design of the wireless information and power transfer systems. The thesis consists of two parts. In the first part we focus on the power transmitter design which addresses the low efficiency issue associated with backscatter communication and WPT. In Chapter 2, we consider a backscatter RFID system with the multi-antenna reader and propose a blind transmit and receive adaptive beamforming algorithm. The interrogation range and data transmission performance are both investigated under such configuration. In Chapter 3 we study wireless power transfer by the beamspace large-scale MIMO system with lens antenna arrays. We first present the WPT model for the beamspace MIMO which is derived from the spatial MIMO model. By constraining on the number of RF chains in the transmitter, we formulate two WPT optimization problems: the sum power transfer problem and the max-min power transfer problem. For both problems we consider two different transmission schemes, the multi-stream and uni-stream transmissions, and we propose different algorithms to solve both problems in both schemes respectively. In the second part we study the network optimization problems in the WPT and backscatter systems. In Chapter 4, we study the resource allocation problem for a RF-powered network, where the objective is to maximize the total data throughput of all sensors. We break the problem into two subproblems: the sensor battery energy utilization problem and the charging power allocation problem of the central node, which is an RF power transmitter that transmits RF power to the sensors. We analyze and show several key properties of both problems, and then propose computationally efficient algorithms to solve both problems optimally. In Chapter 5, we study the time scheduling problem in RF-powered backscatter communication networks, where all transmitters can operates in either backscattering mode or harvest-then-transmit (HTT) mode. The objective is to decide the operating mode of each transmitter and minimize the total transmission time of the network. We also consider both ideal and realistic transmitters based on different internal power consumption models for HTT transmitters. Under both transmitter models we show several key properties, and propose bisection based algorithms which has low computational complexity that solves the problem optimally. The results are then extended to the massive MIMO regime

Dosimetric study of the radiolectric influence of humans into complex environments through determistic simulations and the implementation of a simplified model

The research presented in this thesis falls under the framework of dosimetry and deterministic estimations. A dosimetric study is carried out with the aid of a 3D Ray Launching simulation technique, by means of an in-house developed code at UPNA. Dosimetry is defined as the calculation of the absorbed dose when a tissue is exposed to electromagnetic radiation, in this case, non-ionizing radiation. It has reached a great importance since a part of the society starts to show concern about the exposure of people to artificial exposures caused by mobile phones or Wi-Fi networks. In fact, some entities (administrations and health bodies) are involved in the regulation and the release of guidelines about this subject. The objective of this thesis is to study dosimetry through 3D Ray Launching simulation technique, calibrating it by the implementation of several scenarios where the simulation tool is tested throughout the comparison of theoretical and measurement results. A simplified human body has been also developed with the aim of employing it in different scenarios, performing dosimetric estimations and providing insight on its influence in the electromagnetic power distribution inside an indoor scenario. Finally, obtained results are compared with different guideline thresholds giving an idea of the compliance of the law when usual wireless communication systems are emitting.Programa Oficial de Doctorado en Tecnologías de las Comunicaciones (RD 1393/2007)Komunikazioen Teknologietako Doktoretza Programa Ofiziala (ED 1393/2007

Analyse et exploitation des non linéarités dans les systèmes RFID UHF passifs

Powered by the exploding popularity of the Internet-of-Things (IoT), the demand for tagged devices with labels capable to ensure a reliable communication with added functions beyond the identification, such as sensing, location, health-care, among others, is growing rapidly. Certainly this growing is headed by the well-established Radio Frequency Identification (RFID) technology, and the use of wireless low-cost self-powered tags, in other words passive RFID tags, is the most widespread used alternative. In the constant evolution on this field, usually new software treatments are offered at the application layer with the objective to processing data to produce some new information. Further works aimed at improving the physical layer around the tag antenna miniaturization and matching techniques. So far, little or no work had been done on the exploitation of the communication channel, and certainly none has been done on the exploitation of the non-linear behavior of RFID chips.After presenting the RFID technology and phenomena produced by Radio Frequency (RF) non-linear devices, and leaning in some nearby works on the field, the core of this thesis starts by exposing two characterization platforms for the evaluation of non-linear phenomena presented during the reader-tag communication. One is specialized in radiating measurements considering the whole tag (antenna and chip) under test. The other is specialized in conducted measurements directly over RFID chips, allowing performing different parametric studies (power dependency, impedance, harmonic production, sensitivity). The characterization results show that harmonic signals generated from the passive RFID chip carry information.By exploiting the characterization results and to verify the hypothesis of exploitation of non-linearities in RFID, i.e. the use of harmonic signals, the research is pursued by designing, fabricating, and measuring four different configurations of RFID tags. The new RFID tags operate at the fundamental frequency in the UHF band and at its 3^{rd} harmonic in the microwave band. Antenna design policies, fabrication details, and parametric studies on the performance of the new prototypes are presented. The parametric study takes special care in the antenna structure, kind of chip used, received power, and read range.Finally, some alternatives approaches for the exploitation of non-linear effects generated by rectifying devices are presented. Some theoretical aspects and experimental results are discussed linking the passive RFID technology to the theories of Wireless Power Transfer (WPT) and Electromagnetic Energy Harvesting (EEH). The solution takes advantage of the non-linear nature of rectifying elements in order to maximize the RF-to-DC conversion efficiency of EEH devices and increase the read range of passive RFID tags. The solution triggers on the design of a RF multi-device system. The design procedure and tests consider three non-linear phenomena: (1) the impedance power dependency, (2) the harmonic production, and (3) the rectifying dependence on the RF waveform.Avec l'explosion de l'Internet des Objets (IoT), de nouveaux dispositifs permettant de tagguer les objets sont nécessaires afin de permettre non seulement leur identification mais aussi d'assurer des communications fiables et de nouvelles fonctionnalités comme la détection, la localisation ou la capture d'informations. Cette tendance s'appuie sur la technologie bien établie qu'est la radiofréquence par identification (RFID) et donc l'utilisation d'étiquettes (ou tags) faibles coûts et télé-alimentés. Dans ce contexte, de nombreux travaux au niveau de la couche d'application se tournent vers la mise au point de traitements logiciels complémentaires visant à produire de nouveaux types d'information. D'autres travaux visent à améliorer la couche physique avec l'objectif de miniaturiser encore le tag mais aussi de le doter de nouvelles capacités. Jusqu'à présent, il n'existe quasiment pas de travaux concernant la transmission du signal et aucun sur l'exploitation du comportement non-linéaire des puces RFID. Cette thèse vise à étudier les phénomènes non-linéaires produits lors d'une communication RFID.Dans la première partie, deux plateformes de mesure et de caractérisation spécifiques ont été développées : la première vise à observer les signaux au cours d'une communication RFID, et alors caractériser et analyser les effets liés aux phénomènes non linéaires ; la seconde permet d'effectuer différentes mesures directement sur les puces et les caractériser en termes d'impédance, production d'harmoniques et sensibilité. Ces plateformes ont permis : 1) de mettre en évidence que les fréquences harmoniques sont porteuses d'informations qui peuvent être exploitées et même offrir de nouvelles fonctionnalités ; 2) d'obtenir de nombreuses informations sur les propriétés des puces et d'en établir un modèle électrique précis ; 3) de déterminer des critères permettant d'évaluer la performance des tags dans le contexte étudié.Dans la deuxième partie, plusieurs nouveaux tags RFID ont été conçus, fabriqués, mesurés et évalués. Ces nouveaux tags fonctionnent non seulement dans la bande UHF mais aussi sont adaptés à la troisième harmonique dans la bande des microondes. Une méthodologie et des lignes directives d'aide à la conception de ce type de tags ont été établies et s'appuient sur les deux plateformes développées afin de caractériser les différents éléments. Dans un même temps, les effets liés à la fabrication ont aussi été étudiés et des études paramétriques ont permis de mettre en évidence l'effet sur les performances de la géométrie de l'antenne et du type de puce utilisée.Dans une troisième partie, les études se sont focalisées à exploiter les effets non-linéaires des dispositifs de redressement. L'idée générale est de coupler la RFID passive avec les dispositifs de transferts de puissance et de récupération d'énergie avec pour objectifs 1) de maximiser l'efficacité de conversion RF – continu 2) et d'augmenter la distance de lecture des tags passifs. Plusieurs prototypes ont été réalisés et leurs performances ont été démontrées.L'ensemble de ces travaux a mis en évidence un nouveau concept de communication RFID exploitant les non-linéarités générées par les puces RFID. Ce concept ouvre la voie à de nouvelles applications. et a fait l'objet d'une demande de brevet international

Radio Communications

In the last decades the restless evolution of information and communication technologies (ICT) brought to a deep transformation of our habits. The growth of the Internet and the advances in hardware and software implementations modified our way to communicate and to share information. In this book, an overview of the major issues faced today by researchers in the field of radio communications is given through 35 high quality chapters written by specialists working in universities and research centers all over the world. Various aspects will be deeply discussed: channel modeling, beamforming, multiple antennas, cooperative networks, opportunistic scheduling, advanced admission control, handover management, systems performance assessment, routing issues in mobility conditions, localization, web security. Advanced techniques for the radio resource management will be discussed both in single and multiple radio technologies; either in infrastructure, mesh or ad hoc networks

Taming and Leveraging Directionality and Blockage in Millimeter Wave Communications

To cope with the challenge for high-rate data transmission, Millimeter Wave(mmWave) is one potential solution. The short wavelength unlatched the era of directional mobile communication. The semi-optical communication requires revolutionary thinking. To assist the research and evaluate various algorithms, we build a motion-sensitive mmWave testbed with two degrees of freedom for environmental sensing and general wireless communication.The first part of this thesis contains two approaches to maintain the connection in mmWave mobile communication. The first one seeks to solve the beam tracking problem using motion sensor within the mobile device. A tracking algorithm is given and integrated into the tracking protocol. Detailed experiments and numerical simulations compared several compensation schemes with optical benchmark and demonstrated the efficiency of overhead reduction. The second strategy attempts to mitigate intermittent connections during roaming is multi-connectivity. Taking advantage of properties of rateless erasure code, a fountain code type multi-connectivity mechanism is proposed to increase the link reliability with simplified backhaul mechanism. The simulation demonstrates the efficiency and robustness of our system design with a multi-link channel record.The second topic in this thesis explores various techniques in blockage mitigation. A fast hear-beat like channel with heavy blockage loss is identified in the mmWave Unmanned Aerial Vehicle (UAV) communication experiment due to the propeller blockage. These blockage patterns are detected through Holm\u27s procedure as a problem of multi-time series edge detection. To reduce the blockage effect, an adaptive modulation and coding scheme is designed. The simulation results show that it could greatly improve the throughput given appropriately predicted patterns. The last but not the least, the blockage of directional communication also appears as a blessing because the geometrical information and blockage event of ancillary signal paths can be utilized to predict the blockage timing for the current transmission path. A geometrical model and prediction algorithm are derived to resolve the blockage time and initiate active handovers. An experiment provides solid proof of multi-paths properties and the numeral simulation demonstrates the efficiency of the proposed algorithm