Through-silicon-via-aware prediction and physical design for multi-granularity 3D integrated circuits

The main objective of this research is to predict the wirelength, area, delay, and power of multi-granularity three-dimensional integrated circuits (3D ICs), to develop physical design methodologies and algorithms for the design of multi-granularity 3D ICs, and to investigate the impact of through-silicon vias (TSVs) on the quality of 3D ICs. This dissertation supports these objectives by addressing six research topics. The first pertains to analytical models that predict the interconnects of multi-granularity 3D ICs, and the second focuses on the development of analytical models of the capacitive coupling of TSVs. The third and the fourth topics present design methodologies and algorithms for the design of gate- and block-level 3D ICs, and the fifth topic pertains to the impact of TSVs on the quality of 3D ICs. The final topic addresses topography variation in 3D ICs. The first section of this dissertation presents TSV-aware interconnect prediction models for multi-granularity 3D ICs. As previous interconnect prediction models for 3D ICs did not take TSV area into account, they were not capable of predicting many important characteristics of 3D ICs related to TSVs. This section will present several previous interconnect prediction models that have been improved so that the area occupied by TSVs is taken into account. The new models show numerous important predictions such as the existence of the number of TSVs minimizing wirelength. The second section presents fast estimation of capacitive coupling of TSVs and wires. Since TSV-to-TSV and TSV-to-wire coupling capacitance is dependent on their relative locations, fast estimation of the coupling capacitance of a TSV is essential for the timing optimization of 3D ICs. Simulation results show that the analytical models presented in this section are sufficiently accurate for use at various design steps that require the computation of TSV capacitance. The third and fourth sections present design methodologies and algorithms for gate- and block-level 3D ICs. One of the biggest differences in the design of 2D and 3D ICs is that the latter requires TSV insertion. Since no widely-accepted design methodology designates when, where, and how TSVs are inserted, this work develops and presents several design methodologies for gate- and block-level 3D ICs and physical design algorithms supporting them. Simulation results based on GDSII-level layouts validate the design methodologies and present evidence of their effectiveness. The fifth section explores the impact of TSVs on the quality of 3D ICs. As TSVs become smaller, devices are shrinking, too. Since the relative size of TSVs and devices is more critical to the quality of 3D ICs than the absolute size of TSVs and devices, TSVs and devices should be taken into account in the study of the impact of TSVs on the quality of 3D ICs. In this section, current and future TSVs and devices are combined to produce 3D IC layouts and the impact of TSVs on the quality of 3D ICs is investigated. The final section investigates topography variation in 3D ICs. Since landing pads fabricated in the bottommost metal layer are attached to TSVs, they are larger than TSVs, so they could result in serious topography variation. Therefore, topography variation, especially in the bottommost metal layer, is investigated and two layout optimization techniques are applied to a global placement algorithm that minimizes the topography variation of the bottommost metal layer of 3D ICs.PhDCommittee Chair: Lim, Sung Kyu; Committee Member: Bakir, Muhannad; Committee Member: Kim, Hyesoon; Committee Member: Lee, Hsien-Hsin Sean; Committee Member: Mukhopadhyay, Saiba

Placement for fast and reliable through-silicon-via (TSV) based 3D-IC layouts

The objective of this research is to explore the feasibility of addressing the major performance and reliability problems or issues, such as wirelength, stress-induced carrier mobility variation, temperature, and quality trade-offs, found in three-dimensional integrated circuits (3D ICs) that use through-silicon vias (TSVs) at placement stage. Four main works that support this goal are included. In the first work, wirelength of TSV-based 3D ICs is the main focus. In the second work, stress-induced carrier mobility variation in TSV-based 3D ICs is examined. In the third work, temperature inside TSV-based 3D ICs is investigated. In the final work, the quality trade-offs of TSV-based 3D-IC designs are explored. In the first work, a force-directed, 3D, and gate-level placement algorithm that efficiently handles TSVs is developed. The experiments based on synthesized benchmarks indicate that the developed algorithm helps generate GDSII layouts of 3D-IC designs that are optimized in terms of wirelength. In addition, the impact of TSVs on other physical aspects of 3D-IC designs is also studied by analyzing the GDSII layouts. In the second work, the model for carrier mobility variation caused by TSV and STI stresses is developed as well as the timing analysis flow considering the stresses. The impact of TSV and STI stresses on carrier mobility variation and performance of 3D ICs is studied. Furthermore, a TSV-stress-driven, force-directed, and 3D placement algorithm is developed. It exploits carrier mobility variation, caused by stress around TSVs after fabrication, to improve the timing and area objectives during placement. In addition, the impact of keep-out zone (KOZ) around TSVs on stress, carrier mobility variation, area, wirelength, and performance of 3D ICs is studied. In the third work, two temperature-aware global placement algorithms are developed. They exploit die-to-die thermal coupling in 3D ICs to improve temperature during placement. In addition, a framework used to evaluate the results from temperature-aware global placements is developed. The main component of the framework is a GDSII-level thermal analysis that considers all structures inside a TSV-based 3D IC while computing temperature. The developed placers are compared with several state-of-the-art placers published in recent literature. The experimental results indicate that the developed algorithms help improve the temperature of 3D ICs effectively. In the final work, three block-level design styles for TSV-based die-to-wafer bonded 3D ICs are discussed. Several 3D-IC layouts in the three styles are manually designed. The main difference among these layouts is the position of TSVs. Finally, the area, wirelength, timing, power, temperature, and mechanical stress of all layouts are compared to explore the trade-offs of layout quality.PhDCommittee Chair: Lim, Sung Kyu; Committee Member: Bakir, Muhannad; Committee Member: Kim, Hyesoon; Committee Member: Mukhopadhyay, Saibal; Committee Member: Swaminathan, Madhava

Fast 3D Integrated Circuit Placement Methodology using Merging Technique

In the recent years the advancement in the field of microelectronics integrated circuit (IC) design technologies proved to be a boon for design and development of various advanced systems in-terms of its reduction in form factor, low power, high speed and with increased capacity to incorporate more designs. These systems provide phenomenal advantage for armoured fighting vehicle (AFV) design to develop miniaturised low power, high performance sub-systems. One such emerging high-end technology to be used to develop systems with high capabilities for AFVs is discussed in this paper. Three dimensional IC design is one of the emerging field used to develop high density heterogeneous systems in a reduced form factor. A novel grouping based partitioning and merge based placement (GPMP) methodology for 3D ICs to reduce through silicon vias (TSVs) count and placement time is proposed. Unlike state-of-the-art techniques, the proposed methodology does not suffer from initial overlap of cells during intra-layer placement which reduces the placement time. Connectivity based grouping and partitioning ensures less number of TSVs and merge based placement further reduces intra layer wire-length. The proposed GPMP methodology has been extensively against the IBMPLACE database and performance has been compared with the latest techniques resulting in 12 per cent improvement in wire-length, 13 per cent reduction in TSV and 1.1x improvement in placement time

Thermal management of the through silicon vias in 3-D integrated circuits

The through silicon via technology is a promising and preferred way to realize the reliable interconnection for 3-D integrated circuit integration. However, its size and the property of the filled-materials are two factors affecting the thermal behavior of the integrated circuits. In this paper, we design 3-D integrated circuits with different through silicon via models and analyze the effect of different material-filled through silicon vias, aspect ratio and thermal conductivity of the dielectric on the steady-state temperature profiles. The results presented in this paper are expected to aid in the development of thermal design guidelines for through silicon vias in 3-D integrated circuits

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

CAD methodologies for low power and reliable 3D ICs

The main objective of this dissertation is to explore and develop computer-aided-design (CAD) methodologies and optimization techniques for reliability, timing performance, and power consumption of through-silicon-via(TSV)-based and monolithic 3D IC designs. The 3D IC technology is a promising answer to the device scaling and interconnect problems that industry faces today. Yet, since multiple dies are stacked vertically in 3D ICs, new problems arise such as thermal, power delivery, and so on. New physical design methodologies and optimization techniques should be developed to address the problems and exploit the design freedom in 3D ICs. Towards the objective, this dissertation includes four research projects. The first project is on the co-optimization of traditional design metrics and reliability metrics for 3D ICs. It is well known that heat removal and power delivery are two major reliability concerns in 3D ICs. To alleviate thermal problem, two possible solutions have been proposed: thermal-through-silicon-vias (T-TSVs) and micro-fluidic-channel (MFC) based cooling. For power delivery, a complex power distribution network is required to deliver currents reliably to all parts of the 3D IC while suppressing the power supply noise to an acceptable level. However, these thermal and power networks pose major challenges in signal routability and congestion. In this project, a co-optimization methodology for signal, power, and thermal interconnects in 3D ICs is presented. The goal of the proposed approach is to improve signal, thermal, and power noise metrics and to provide fast and accurate design space explorations for early design stages. The second project is a study on 3D IC partition. For a 3D IC, the target circuit needs to be partitioned into multiple parts then mapped onto the dies. The partition style impacts design quality such as footprint, wirelength, timing, and so on. In this project, the design methodologies of 3D ICs with different partition styles are demonstrated. For the LEON3 multi-core microprocessor, three partitioning styles are compared: core-level, block-level, and gate-level. The design methodologies for such partitioning styles and their implications on the physical layout are discussed. Then, to perform timing optimizations for 3D ICs, two timing constraint generation methods are demonstrated that lead to different design quality. The third project is on the buffer insertion for timing optimization of 3D ICs. For high performance 3D ICs, it is crucial to perform thorough timing optimizations. Among timing optimization techniques, buffer insertion is known to be the most effective way. The TSVs have a large parasitic capacitance that increases the signal slew and the delay on the downstream. In this project, a slew-aware buffer insertion algorithm is developed that handles full 3D nets and considers TSV parasitics and slew effects on delay. Compared with the well-known van Ginneken algorithm and a commercial tool, the proposed algorithm finds buffering solutions with lower delay values and acceptable runtime overhead. The last project is on the ultra-high-density logic designs for monolithic 3D ICs. The nano-scale 3D interconnects available in monolithic 3D IC technology enable ultra-high-density device integration at the individual transistor-level. The benefits and challenges of monolithic 3D integration technology for logic designs are investigated. First, a 3D standard cell library for transistor-level monolithic 3D ICs is built and their timing and power behavior are characterized. Then, various interconnect options for monolithic 3D ICs that improve design quality are explored. Next, timing-closed, full-chip GDSII layouts are built and iso-performance power comparisons with 2D IC designs are performed. Important design metrics such as area, wirelength, timing, and power consumption are compared among transistor-level monolithic 3D, gate-level monolithic 3D, TSV-based 3D, and traditional 2D designs.PhDCommittee Chair: Lim, Sung Kyu; Committee Member: Bakir, Muhannad; Committee Member: Kim, Hyesoon; Committee Member: Lee, Hsien-Hsin; Committee Member: Mukhopadhyay, Saiba

TSV placement optimization for liquid cooled 3D-ICs with emerging NVMs

Three dimensional integrated circuits (3D-ICs) are a promising solution to the performance bottleneck in planar integrated circuits. One of the salient features of 3D-ICs is their ability to integrate heterogeneous technologies such as emerging non-volatile memories (NVMs) in a single chip. However, thermal management in 3D-ICs is a significant challenge, owing to the high heat flux (~ 250 W/cm2). Several research groups have focused either on run-time or design-time mechanisms to reduce the heat flux and did not consider 3D-ICs with heterogeneous stacks. The goal of this work is to achieve a balanced thermal gradient in 3D-ICs, while reducing the peak temperatures. In this research, placement algorithms for design-time optimization and choice of appropriate cooling mechanisms for run-time modulation of temperature are proposed. Specifically, an architectural framework which introduce weight-based simulated annealing (WSA) algorithm for thermal-aware placement of through silicon vias (TSVs) with inter-tier liquid cooling is proposed for design-time. In addition, integrating a dedicated stack of emerging NVMs such as RRAM, PCRAM and STTRAM, a run-time simulation framework is developed to analyze the thermal and performance impact of these NVMs in 3D-MPSoCs with inter-tier liquid cooling. Experimental results of WSA algorithm implemented on MCNC91 and GSRC benchmarks demonstrate up to 11 K reduction in the average temperature across the 3D-IC chip. In addition, power density arrangement in WSA improved the uniformity by 5%. Furthermore, simulation results of PARSEC benchmarks with NVM L2 cache demonstrates a temperature reduction of 12.5 K (RRAM) compared to SRAM in 3D-ICs. Especially, RRAM has proved to be thermally efficient replacement for SRAM with 34% lower energy delay product (EDP) and 9.7 K average temperature reduction