Development of the future generation of smart high voltage connectors and related components for substations, with energy autonomy and wireless data transmission capability

The increased dependency on electricity of modern society, makes reliability of power transmission systems a key point. This goal can be achieved by continuously monitoring power grid parameters, so possible failure modes can be predicted beforehand. It can be done using existing Information and Communication Technologies (ICT) and Internet of Things (10T) technologies that include instrumentation and wireless communication systems, thus forming a wireless sensor network (WSN). Electrical connectors are among the most critical parts of any electrical system and hence, they can act as nodes of such WSN. Therefore, the fundamental objective of this thesis is the design, development and experimental validation of a self-powered IOT solution for real-time monitoring of the health status of a high-voltage substation connector and related components of the electrical substation. This new family of power connectors is called SmartConnector and incorporates a thermal energy harvesting system powering a microcontroller that controls a transmitter and several electronic sensors to measure the temperature, current and the electrical contact resistance (ECR) of the connector. These measurements are sent remotely via a Bluetooth 5 wireless communication module to a local gateway, which further transfers the measured data to a database server for storage as well as further analysis and visualization. By this way, after suitable data processing, the health status of the connector can be available in real-time, allowing different appealing functions, such as assessing the correct installation of the connector, the current health status or its remaining useful life (RUL) in real-time. The same principal can also be used for other components of substation like spacers, insulators, conductors, etc. Hence, to prove universality of this novel approach, a similar strategy is applied to a spacer which is capable of measuring uneven current distribution in three closely placed conductors. This novel IOT device is called as SmartSpacer. Care has to be taken that this technical and scientific development has to be compatible with existing substation bus bars and conductors, and especially to be compatible with the high operating voltages, i.e., from tens to hundreds of kilo-Volts (kV), and with currents in the order of some kilo-pm peres (kA). Although some electrical utilities and manufacturers have progressed in the development of such technologies, including smart meters and smart sensors, electrical device manufacturers such as of substation connectors manufacturers have not yet undertaken the technological advancement required for the development of such a new family of smart components involved in power transmission, which are designed to meet the future needs.La mayor dependencia de la electricidad de la sociedad moderna hace que la fiabilidad de los sistemas de transmisión de energía sea un punto clave. Este objetivo se puede lograr mediante la supervisión continua de los parámetros de la red eléctrica, por lo que los posibles modos de fallo se pueden predecir de antemano. Se puede hacer utilizando las tecnologías existentes de Tecnologías de la Información y la Comunicación (1CT) e Internet de las cosas (lo T) que incluyen sistemas de instrumentación y comunicación inalámbrica, formando así una red de sensores inalámbricos (WSN). Los conectores eléctricos se encuentran entre las partes más críticas de cualquier sistema eléctrico y, por lo tanto, pueden actuar como nodos de dicho VVSN. Por lo tanto, el objetivo fundamental de esta tesis es el diseño, desarrollo y validación experimental de una solución IOT autoalimentada para la supervisión en tiempo real del estado de salud de un conector de subestación de alta tensión y componentes relacionados de la subestación eléctrica. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia del contacto eléctrico (ECR) del conector. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia al contacto eléctrico (ECR) del conector. De esta manera, después del procesamiento de datos adecuado, el estado de salud del conector puede estar disponible en tiempo real, permitiendo diferentes funciones atractivas, como evaluar la correcta instalación del conector, el estado de salud actual o su vida útil restante (RUL) en tiempo real. El mismo principio también se puede utilizar para otros componentes de la subestación como espaciadores, aislantes, conductores, etc. Por lo tanto, para demostrar la universalidad de este enfoque novedoso, se aplica una estrategia similar a un espaciador, que es capaz de medir la distribución de corriente desigual en tres conductores estrechamente situados. Hay que tener cuidado de que este desarrollo técnico y científico tenga que sea compatible con las barras y "busbars" de subestación existentes, y sobre todo para ser compatible con las altas tensiones de funcionamiento, es decir, de decenas a cientos de kilovoltios (kV), y con corrientes en el orden de algunos kilo-Amperes (kA). Aunque algunas empresas eléctricas y fabricantes han progresado en el desarrollo de este tipo de tecnologías, incluidos medidores inteligentes y sensores inteligentes, los fabricantes de dispositivos eléctricos, como los fabricantes de conectores de subestación, aún no han emprendido el avance tecnológico necesario para el desarrollo de una nueva familia de componentes intel

Standards-based wireless sensor networks for power system condition monitoring

This paper assesses the industrial needs motivating interest in wireless monito ring within the power industry, and reviews applications of WSN technology for substation condition monitoring (Section 2). A key contribution is the identification of a set of technical requirements for substation - based WSNs, focused around security requi rements, robustness to RF noise, and other utility - specific concerns (Section 3). Section 4 comprehensively assesses the suitability of various IWSN protocols for substation environments, using these requirements. A case study implementation of one standar d, ISA100.11a, is reported in Section 5, along with deployment experience. The paper concludes by describing future research challenges for WSN protocols which are specific to this domain

A wireless system for monitoring leakage current in electrical substation equipment

In this paper, the design and the development of a remote system for continuous monitoring of leakage currents and ground currents in high voltage electrical substations are proposed. Based on wireless local area network technology, the system can be used to monitor continuously a variety of plants within the substation and has low power consumption with inbuilt overvoltage protection. It consists of a transmitter module equipped with a data acquisition (DAQ) system connected to leakage current and voltage sensors, and a receiver module connected to a remote controller for data processing and storage. The principle of operation and the characteristics of the various components of the system are described. Validation tests have been used to verify its performance in three different test situations: A) laboratory monitoring of the leakage current and voltage of a distribution surge arrester; B) laboratory measurement of the leakage current of an outdoor insulator; and C) field monitoring of the earth current and potential rise of high-voltage tower. The measured results are in close agreement with those recorded directly through a DAQ card with fiber-optic and coaxial cable connected systems. Data processing is carried out at the receiving end so that the monitored parameter is displayed continuously or at specified time intervals. The operation of the system has been tested and proved resilient under high-frequency interference signals such as those generated by corona and surface discharges

Feasibility study on thermal energy harvesting for low powered electronics in high-voltage substations

Electronic devices combining sensors, wireless communications, and data processing capability allow easing predictive maintenance tasks in many applications. This paper applies this approach in power connectors for high-voltage electrical substations, which are transformed into smart connectors. Such connectors are often linked to tubular aluminum bus bars, whose temperature increases due to the Joule losses generated by the combined effect of the electrical resistance and the electric current. Since the human intervention must be minimized, an energy harvesting system is required to supply the electronics of the smart connectors. To this end, a thermoelectric module (TEM) is used to transform heat power into electrical power. Since the voltage provided by the TEM is very low, a suitable power converter is used to supply the electronics of the smart connector. This work analyzes the effect of the various parameters that affect the power generated by the TEM when placed on a substation bus bar. Experiments have been carried out by placing a TEM with different configurations on different types of bus bars for diverse operating conditions.Peer ReviewedPostprint (published version

Power‐Over‐Fiber Applications for Telecommunications and for Electric Utilities

Beyond telecommunications, optical fibers can also transport optical energy to powering electric or electronic devices remotely. This technique is called power over fiber (PoF). Besides the advantages of optical fiber (immunity to electromagnetic interferences and electrical insulation), the employment of a PoF scheme can eliminate the energy supplied by metallic cable and batteries located at remote sites, improving the reliability and the security of the system. Smart grid is a green field where PoF can be applied. Experts see smart grid as the output to a new technological level seeks to incorporate extensively technologies for sensing, monitoring, information technology, and telecommunications for the best performance electrical network. On the other hand, in telecommunications, PoF can be used in applications, such as remote antennas and extenders for passive optical networks (PONs). PoF can make them virtually passives. We reviewed the PoF concept, its main elements, technologies, and applications focusing in access networks and in smart grid developments made by the author’s research group

Emerging technologies and future trends in substation automation systems for the protection, monitoring and control of electrical substations

Tese de Mestrado Integrado. Engenharia Electrotécnica e de Computadores (Automação). Faculdade de Engenharia. Universidade do Porto. 201

Condition monitoring system and faults detection for impedance bonds from railway infrastructure

Nowadays, sensors and condition monitoring systems are expanding rapidly and becoming cheaper. This contributes to increasing developments in condition monitoring in railway transport infrastructure. A condition monitoring system that uses an online device and sensors to acquire electrical parameters from railway infrastructure has been developed and applied for fault detection and diagnosis of impedance bonds. The impedance bond condition is monitored in real-time using current and temperature sensors, providing early warning if predefined thresholds are exceeded in terms of currents, imbalance currents, and temperatures. The proposed method and the developed monitoring device have been validated in the railway laboratory to confirm its capability to detect defects. The acquired parameters from impedance bonds are used to extract thermal stresses and technical conditions of this equipment. Experimental results and appropriate data analysis are included in the article.info:eu-repo/semantics/publishedVersio

Internet of Things-aided Smart Grid: Technologies, Architectures, Applications, Prototypes, and Future Research Directions

Traditional power grids are being transformed into Smart Grids (SGs) to address the issues in existing power system due to uni-directional information flow, energy wastage, growing energy demand, reliability and security. SGs offer bi-directional energy flow between service providers and consumers, involving power generation, transmission, distribution and utilization systems. SGs employ various devices for the monitoring, analysis and control of the grid, deployed at power plants, distribution centers and in consumers' premises in a very large number. Hence, an SG requires connectivity, automation and the tracking of such devices. This is achieved with the help of Internet of Things (IoT). IoT helps SG systems to support various network functions throughout the generation, transmission, distribution and consumption of energy by incorporating IoT devices (such as sensors, actuators and smart meters), as well as by providing the connectivity, automation and tracking for such devices. In this paper, we provide a comprehensive survey on IoT-aided SG systems, which includes the existing architectures, applications and prototypes of IoT-aided SG systems. This survey also highlights the open issues, challenges and future research directions for IoT-aided SG systems