Development and operation of the twin radio frequency single electron transistor for solid state qubit readout

Ultra-sensitive detectors and readout devices based on the radio frequency single electron transistor (rf-SET) combine near quantum-limited sensitivity with fast operation. Here we describe a twin rf-SET detector that uses two superconducting rf-SETs to perform fast, real-time cross-correlated measurements in order to distinguish sub-electron signals from charge noise on microsecond time-scales. The twin rf-SET makes use of two tuned resonance circuits to simultaneously and independently address both rf-SETs using wavelength division multiplexing (WDM) and a single cryogenic amplifier. We focus on the operation of the twin rf-SET as a charge detector and evaluate the cross-talk between the two resonance circuits. Real time suppression of charge noise is demonstrated by cross correlating the signals from the two rf-SETs. For the case of simultaneous operation, the rf-SETs had charge sensitivities of $\delta q_{SET1} = 7.5 \mu e/\sqrt{Hz}$ and $\delta q_{SET2} = 4.4 \mu e/\sqrt{Hz}$.Comment: Updated version, including new content. Comments most welcome: [email protected] or [email protected]

Very high-current-density Nb/AlN/Nb tunnel junctions for low-noise submillimeter mixers

We have fabricated and tested submillimeter-wave superconductor–insulator–superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc[approximate]30 kA cm–2). The junctions have low-resistance-area products (RNA[approximate]5.6 Omega µm2), good subgap-to-normal resistance ratios Rsg/RN[approximate]10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that omegaRNC = 1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX = 110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits

Phase modulating the Urbana radar

The design and operation of a switched phase modulation system for the Urbana Radar System are discussed. The system is implemented and demonstrated using a simple procedure. The radar system and circuits are described and analyzed

Feed system design and experimental results in the uhf model study for the proposed Urbana phased array

The effects of atmospheric turbulence and the basis for the coherent scatter radar techniques are discussed. The reasons are given for upgrading the Radar system to a larger steerable array. Phase array theory pertinent to the system design is reviewed, along with approximations for maximum directive gain and blind angles due to mutual coupling. The methods and construction techniques employed in the UHF model study are explained. The antenna range is described, with a block diagram for the mode of operation used

On the design of high-efficiency RF Doherty power amplifiers

Power amplifiers (PAs) are one of the most crucial elements in wireless standards becasue they are the most power hungry subsystems. These elements have to face an important issue, which is the power efficiency, a fact related with the output back-off (OBO). But the OBO depends on the kind of modulated signal, in proportion to the modulated signal peak-to-average power ratio (PAPR). The higuer is the data rate, the higer is the OBO, and consequently the lower is the efficiency. A low efficiency of PAs causes the waste of energy as heat. Furthermore, the trade-off between linearity and efficiency in PAs is another major issue. To cope with the undesired circumstances producing efficiency degradation, the Doherty power amplifier (DPA) is one of the useful techniques which provide high efficiency for high PAPR of modern communication signals. Nevertheless, the limited bandwidth (BW) of this kind of PAs (about 10% of fractional bandwidth) and its importance (in modern wireless systems such as LTE, WiMAX, Wi-Fi and satellite systems) have encouraged the researchers to improve this drawback in recent years. Some typical BW limiting factors effect on the performance of DPAs: i) quarter-wave length transformers, ii) phase compensation networks in/output matching circuits, iii) offset lines and device non-idealities; The quarter-wave length transformers performs as an inverter impedance in the load modulation technique of DPAs. The future objective in designing DPAs is to decrease the impact of these issues. In this context, this PhD-thesis is focused on improving fractional bandwidth of DPAs using the new methods that are related to impedance transformers instead of impedance inverters in the load modulation technique. This study is twofold. First, it is presented a novel DPA where a wideband GaN DPA in the 2.5 GHz band with an asymmetrical Wilkinson splitter. The impedance transformer of the proposed architecture is based on a matching network including a tapered line with multi-section transformer in the main stage. The BW of this DPA has ranged from 1.8 to 2.7 GHz. Plus, the obtained power efficiency (drain) is higher than 33% in the whole BW at both maximum and OBO power levels. Second, based on the benefits of the Klopfenstein taper, a promising DPA design is proposed where a Klopfenstein taper replaces the tapered line. In fact, this substitution results on reducing the reflection coefficient of the transformer. From a practical prototype realization of this novel Doherty-like PA in the 2.25 GHz band, this modification has demonstrated that the resulting DPA BW is increased in comparison to the conventional topology while keeping the efficiency figures. Moreover, this study also shows that the Klopfenstein taper based design allows an easy tuning of the group delay through the output reactance of the taper, resulting in a more straightforward adjustments than other recently published designs where the quarter-wave transformer is replaced by multi-section transmission lines (hybrid or similar). Experimental results have shown 43-54% of drain efficiency at 42 dBm output power, in the range of 1.7 to 2.75 GHz. Concretely, the results presented in this novel Doherty-like PA implies an specific load modulation technique that uses the mixed Klopfenstein tapered line together with a multi-section transformer in order to obtain high bandwidth with the usual efficiency in DPAs.Los amplificadores de potencia (PAs) son uno de los elementos más importantes para los transmisores inalámbricos desde el punto de vista del consumo energético. Un aspecto muy importante es su eficiencia energética, un concepto relacionado con el back-off de salida (OBO), que a su vez viene condicionadpo por el PAPR de la señal modulada a amplificar. Una baja eficiencia de los PA hace que la pérdida de energía se manifieste en forma de calor. De hecho, esta cuestión conduce al incremento de los costes y tamaño, esto último por los radiadores. Además, el compromiso entre la linealidad y la eficiencia en los PA es otro problema importante. Para hacer frente a las circunstancias que producen la degradación de la eficiencia, el amplificador de potencia tipo Doherty (DPA) es una de las técnicas más útiles que proporcionan una buena eficiencia incluso para los altos PAPR comunes en señales de comunicación modernos. Sin embargo, el limitado ancho de banda (BW) de este tipo de PA (alrededor del 10% del ancho de banda fraccional) y su importancia (en los sistemas inalámbricos modernos, tales como LTE, WiMAX, Wi-Fi y sistemas de satélites) han animado a los investigadores para mejorar este inconveniente en los últimos años. Algunos aspectos típicos que limitan el BW en los DPA son: i) transformadores de longitud de cuarto de onda, ii) redes de compensación de fase y circuitos de adaptación de salida, iii) compensación de las líneas y los dispositivos no ideales. Los transformadores de cuarto de onda actuan como un inversor de impedancia en la técnica de modulación de carga de la DPA "("load modulation"). Concretamente, el objetivo futuro de diseño de DPA es disminuir el impacto de estos problemas. En este contexto, esta tesis doctoral se centra en mejorar el ancho de banda fraccional de DPA utilizando los nuevos métodos que están relacionados con el uso de transformadores de impedancias en vez de inversores en el subcircuito de modulación de carga. Este estudio tiene dos niveles. En primer lugar, se presenta una novedosa estructura del DPA de banda ancha usándose dispositivos de GaN en la banda de 2,5 GHz con un divisor Wilkinson asimétrico. El transformador de impedancias de la arquitectura propuesta se basa en una red de adaptación, incluyendo una línea cónica con múltiples secciones del transformador en la etapa principal. El BW de este DPA ha sido de 1,8 a 2,7 GHz. Además, se obtiene una eficiencia de drenador de más del 33% en todo el BW, tanto a nivel de potencia máxima como a nivel del OBO. En segundo lugar, aprovechando los beneficios de un adaptador de Klopfenstein, se propone un nuevo diseño del DPA. Con la sustitución de la lina conica por el Klopfenstein se reduce el coeficiente de reflexión de transformador de impedancias. Sobre un prototipo práctico de esta nueva estructura del Doherty, en la banda de 2,25 GHz, se ha demostrado que el BW resultante se incrementa en comparación con la topología convencional mientras se mantienen las cifras de eficiencia. Por otra parte, en este estudio se demuestra que el diseño basado en el Klopfenstein permite una afinación fácil del retardo de grupo a través de la reactancia de salida del taper, lo que resulta en un ajuste más sencillo que otros diseños publicados recientemente en el que el transformador de cuarto de onda se sustituye por multi-líneas de transmisión de la sección (híbridos o similar). Los resultados experimentales han mostrado un 43-54% de eficiencia de drenador sobre 42 dBm de potencia de salida, en el intervalo de 1,7 a 2,75 GHz. Concretamente, los resultados presentados en esta nueva estructura tipo-Doherty implican una técnica de modulación de carga que utiliza una combinación de un Klopfenstein junto con un transformador de múltiples secciones con el fin de obtener un alto ancho de banda con la eficiencia habitual en DPAs.Els amplificadors de potència (PA) són un dels elements més importants per els sistemes ràdio ja que sone ls principals consumidors d'energía. Un aspecte molt important és l'eficiència de l'amplificador, aspecte relacionat amb el back-off de sortida (OBO) que a la seva vegada ve condicionat pel PAPR del senyal modulat. Una baixa eficiència dels PA fa que la pèrdua d'energia en manifesti en forma de calor. De fet, aquesta qüestió porta a l'increment dels costos i grandària, degut als dissipadors de calor. A més, el compromís entre la linealitat i l'eficiència en els PA es un altre problema important. Per fer front a les circumstàncies que porten a la degradació de l'eficiència, l'amplificador de potència Doherty (DPA) és una de les tècniques més útils i que proporcionen una bona eficiència per als alts PAPR comuns en senyals de comunicació moderns. No obstant això, l'ample de banda limitat (BW) d'aquest tipus de PA (al voltant del 10% de l'ample de banda fraccional) i la seva importància (en els sistemes moderns, com ara LTE, WiMAX, Wi-Fi i sistemes de satèl·lits) han animat els investigadors per millorar aquest inconvenient en els últims anys. Alguns aspectes tipicament limitadors del BW en els DPA son: i) transformadors de longitud d'quart d'ona, ii) xarxes de compensació de fase en circuits / adaptacions de sortida, iii) compensació de les línies i els dispositius no ideals. Els transformadors de quart d'ona s'utilitzen com a inversors d'impedàncies en la tècnica de modulació de càrrega del DPA ("load modulation"). Concretament, l'objectiu futur de disseny d'DPA és disminuir l'impacte d'aquests problemes. En aquest context, aquesta tesi doctoral es centra en millorar l'ample de banda fraccional dels DPA utilitzant nous mètodes que estan relacionats amb l'ús de transformadors d'impedàncies, en comptes d'inversors, en el subcircuit de modulació de càrrega. Aquest treball té dos nivells. En primer lloc, es presenta un DPA novedós que fa servir dispositus GaN DPA a la banda de 2,5 GHz amb un divisor Wilkinson asimètric. El transformador d'impedàncies de l'arquitectura proposada es basa en una xarxa d'adaptació, incloent una línia cònica amb múltiples seccions del transformador en l'etapa principal. El BW d'aquest DPA ha mostrat ser d'1,8 a a 2,7 GHz. A més, s'obté una eficiència de drenador de més del 33% en tot el BW, tant a nivell de potència màxima com de OBO. En segon lloc, sobre la base dels beneficis del adaptador de Klopfenstein, un proposa un nou disseny on un Klopfenstein substitueix la anterior línia cònica. Aquesta substitució repercuteix en la reducció del coeficient de reflexió de transformador d'impedàncies.Des d'una realització pràctica (prototipus) d'aquest nou amplificador tipus Doherty a la banda de 2,25 GHz, s'ha demostrat que el BW resultant s'incrementa en comparació amb la topologia convencional mentre es mantenen les xifres d'eficiència. D'altra banda, en aquest estudi es demostra que el disseny basat en el Klopfenstein permet una afinació fàcil del retard de grup a través de la reactància de sortida de la forma cònica, el que resulta en un ajust més senzill que altres dissenys publicats recentment en què el transformador de quart d'ona es substitueix per multi-línies de transmissió de la secció (híbrids o similar). Els resultats experimentals han mostrat un 43-54% d'eficiència de drenador en 42 dBm de potència de sortida, en l'interval de 1,7-2,75 GHz. Concretament, els resultats presentats en aquest nou amplificador tipus Doherty impliquen una tècnica de modulació de càrrega específic que utilitza una combinació del Klopfenstein juntament amb un transformador de múltiples seccions per tal d'obtenir un alt ample de banda amb la usual eficiència en DPAs.Postprint (published version

Passive and active components development for broadband applications

Recently, GaN HEMTs have been proven to have numerous physical properties, resulting in transistors with greatly increased power densities when compared to the other well-established FET technologies. This advancement spurred research and product development towards power-band applications that require both high power and high efficiency over the wide band. Even though the use of multiple narrow band PAs covering the whole band has invariably led to better performance in terms of efficiency and noise, there is an associated increase in cost and in the insertion loss of the switches used to toggle between the different operating bands. The goal, now, of the new technology is to replace the multiple narrow band PAs with one broadband PA that has a comparable efficiency performance. In our study here, we have investigated a variety of wide band power amplifiers, including class AB PAs and their implementation in distributed and feedback PAs.Additionally, our investigation has included switching-mode PAs as they are well-known for achieving a relatively high efficiency. Besides having a higher efficiency, they are also less susceptible to parameter variations and could impose a lower thermal stress on the transistors than the conventional-mode PAs. With GaN HEMTs, we have demonstrated: a higher than 37 dBm output power and a more than 30% drain efficiency over 0.02 to 3 GHz for the distributed power amplifier; a higher than 30 dBm output power with more than a 22% drain efficiency over 0.1 to 5 GHz for the feedback amplifier; and at least a 43 dBm output power with a higher than 63% drain efficiency over 0.05 to 0.55 GHz for the class D PA. In many communication applications, however, achieving both high efficiency and linearity in the PA design is required. Therefore, in our research, we have evaluated several linearization and efficiency enhancement techniques.We selected the LInear amplification with Nonlinear Components (LINC) approach. Highly efficient combiner and novel efficiency enhancement techniques like the power recycling combiner and adaptive bias LINC schemes have been successfully developed and verified to achieve a combined high efficiency with a relatively high linearity

Design, Modeling, and Testing of Microstrip Patch Antenna Arrays for Vertical Takeoff & Landing Aircraft

A major shortcoming of aircraft antennas for autonomous landing systems is the acquisition and tracking errors resulting because of the illumination of the airframe components by the 360° azimuth beamwidth of a low gain omni-directional antenna. Also, existing low and high gain antennas currently found in the marketplace are both expensive and time-consuming to manufacture. The purpose of this thesis is twofold: to develop a low gain omni-directional antenna that radiates only in the forward direction and to develop a high gain antenna that is less expensive compared to antennas currently found in landing systems. Microstrip patch antenna arrays are selected due to their light weight and low cost. The design, numerical modeling, and experimental characterization of two types of microstrip patch antenna arrays are described. CST's Microwave Studio, a three-dimensional electromagnetic simulator, is used to model, simulate, and optimize the performance of the antennas. The antennas have been fabricated and the return loss and radiation patterns were measured. Return loss comparisons between the simulated and measured antennas show a difference of nearly 500 MHz in the resonance frequency for both the low and high gain arrays. Simulated and measured peak directivities differ by as much as 1.7 dB. These differences between the simulated and measured results are believed to be caused by manufacturing tolerance uncertainties as well as by some design details that were intentionally not accounted for in the modeled antennas

Wideband Wilkinson Power Divider For Uav Phased Array Radar

The purpose of this project is to design a wideband Wilkinson power divider as part of an active phased array radar system for use in Unmanned Aerial Vehicle (UAV) applications. In order to comply with the entire system, the power divider was restricted in size, operating frequency, and bandwidth. The proposed power divider was integrated into a 10 GHz phased array system for future development in a transmitting and receiving system. The Wilkinson power divider was designed to provide 2 GHz bandwidth centered at 10 GHz. In order to provide the bandwidth, a 4&ndashstage Wilkinson power divider was designed and fabricated. It was then tested thoroughly to provide Printed Circuit Board (PCB) characteristics for integration within the system. Port isolation, phase error, and PCB power losses were found for the power divider and recorded to provide better integration into the radar system. The experimental results compared well with the simulated models created in the design phase. The final modularly designed phased array radar consisted of a Vivaldi antenna array, phase shifter and amplifier module, and control module. The focus of the work presented is the Wilkinson power divider that was designed to meet stringent design requirements for space, operating frequency, and phase error. The result is a fabricated Wilkinson power divider that met all the requirements and the module functions within the phased array system

Development of a solid state amplifier for the 3rd harmonic cavity for ALBA synchrotron light source

In Synchrotron Light Source facilities with high energy and low emittance electron beams different techniques for improving the quality of the synchrotron light for the users are applied. With this aim ALBA, the Spanish 3rd generation Synchrotron Light Source, is developing a 3rd Harmonic radiofrequency (RF) system as a system additional to the main RF system of the storage ring. This system will consist of four normal conducting active cavities at 1.5 GHz that will provide the required 1.1 MV accelerating voltage to the electron beam and will be fed by four 20 kW power transmitters. This power will be generated by modular Solid State Power Amplifiers (SSPAs) in a continuous wave mode at 1.5 GHz. On the basis of preliminary studies it has been decided that the architecture of each 20 kW power transmitter is a tree diagram made up of primary 1 kW SSPA modules connected in parallel in a combination array. The present PhD thesis is devoted to the design, building and evaluation of a prototype of the 1 kW SSPA module formed four 250 W primary power amplifier modules. Accordingly, all subsystems, namely input and output matching networks of the 250 W primary module, and a four-way power splitter, a four-way power combiner and a novel directivity compensated directional coupler for the non-invasive power monitoring of the 1 kW power amplifier were also designed and their prototypes were tested. A final evaluation of the combined 1 kW SSPA prototype module was successfully carried out and has shown good performance.En las instalaciones de tipo Fuentes de luz de sincrotrón de haz de electrones de alta energía y baja emitancia se aplican diferentes técnicas de mejora de la calidad de la luz de sincrotrón. Con este objetivo, el ALBA, la fuente española de luz de sincrotrón de la tercera generación, está desarrollando un sistema de radiofrecuencia (RF) de la 3ª Harmónica como un sistema adicional al sistema de RF principal del anillo de almacenamiento. Este sistema consistirá de cuatro cavidades activas de conductividad normal de frecuencia 1,5 GHz que suministrarán un voltaje acelerador de 1.1 MV necesario para el haz de electrones y que serán alimentadas por cuatro transmisores de potencia de 20 kW. Esta potencia será generada en modo de onda continua a frecuencia 1.5 GHz por amplificadores de potencia de estado sólido (APES) de estructura modular. A partir de unos estudios preliminares se ha decidido que la arquitectura de cada transmisor de potencia de 20 kW es de tipo diagrama de árbol que consiste de APES primarios de potencia 1 kW conectados en paralelo formando una matriz de combinación. El tema de la presente tesis es el diseño, la construcción y la caracterización de un prototipo del módulo de APES de potencia 1 kW formado por cuatro amplificadores primarios de 250 W de potencia. También, todos subsistemas, concretamente los circuitos de adaptación de entrada y de salida del módulo primario de 250 kW, así como un divisor de cuatro salidas, un combinador de cuatro entradas y un acoplador direccional con una nova solución de compensación de directividad para una monitorización no invasiva han sido diseñados y sus prototipos han sido testeados. La evaluación final de funcionamiento del APES de 1 kW de potencia ha sido realizada con éxito y ha demostrado su buen rendimiento.Postprint (published version