Caractérisation électrique des propriétés d'interface dans les MOSFET nanométriques par des mesures de bruit basse fréquence

In this thesis, electrical properties of gate oxide/channel interface in ultra-scaled nanowire (NW) MOSFETs were experimentally investigated by carrier transport and low-frequency noise (LFN) characterizations. NW FETs, which have aggressively downscaled cross-section of the body, are strong candidates for near future CMOS node. However, the interface quality could be a critical issue due to the large surface/volume ratio, the multiple surface orientations, and additional strain technology to enhance the performance. Understanding of carrier transport and channel interface quality in NW FETs with advanced high-k/metal gate is thus particularly important. LFN provides deep insights into the interface properties of MOSFET without lower limit of required channel size. LFN measurement thus can be a powerful technique for ultra-scaled NW FETs. Also, fitting mobility (such as low-field mobility) extraction by Y-function method is an efficient method. Omega-gate NW FETs were fabricated from FD-SOI substrates, and with Hf-based high-k/metal gate (HfSiON/TiN), reducing detrimental effects by device downscaling. In addition, strain technologies to the channel were additively processed. Tensile strained-SOI substrate was used for NMOS, whereas compressive stressors were used for PMOS devices. Strained Si channel for PMOS was processed by raised SiGe S/D and CESL formations. Strained SiGe channel (SGOI) was also fabricated for further high-performance PMOS FETs. Firstly, the most common Id-Vg was characterized in single-channel NW FETs as the basic performance. Reference SOI NWs provided the excellent static control down to short channel of 17nm. Stressors dramatically enhanced on-current owing to a modification of channel energy-band structure. Then, extracted low-field mobility in NWs also showed large improvement of the performance by stressors. The mobility extraction effectively evaluated FET performance even for ultra-scaled NWs. Next, LFN investigated for various technological and architectural parameters. Carrier number fluctuations with correlated mobility fluctuations (CNF+CMF) model described 1/f noise in all our FETs down to the shortest NWs. Drain current noise behavior was basically similar in both N- and PMOS FETs regardless of technological splits. Larger 1/f noise stemming from S/D regions in PMOS FETs was perfectly interpreted by the CNF+CMF model completed with Rsd fluctuations. This observation highlighted an advantage of SGOI NW with the lowest level of S/D region noise. Geometrical variations altered the CNF component with simple impact of device scaling (reciprocal to both Wtot and Lg). No large impact of surface orientation difference between the channel (100) top and (110) side-walls in [110]-oriented NWs was observed. Scaling regularity with both Wtot and Lg, without much quantum effect, could be attributed to the use of HfSiON/TiN gate and carrier transport occurring mostly near top and side-wall surfaces even in NW geometry. Meanwhile, the CMF factor was not altered by decreasing dimensions, while the mobility strongly depends on the impact. Extracted oxide trap density was roughly steady with scaling, structure, and technological parameter impacts. Simple separation method of the contributions between channel top surface and side-walls was demonstrated in order to evaluate the difference. It revealed that oxide quality on (100) top and (110) side-walls was roughly comparable in all the [110]-devices. The density values lie in similar order as the recent reports. An excellent quality of the interface with HfSiON/TiN gate was thus sustained for all our technological and geometrical splits. Finally, our NWs fulfilled 1/f LFN requirements stated in the ITRS 2013 for future MG CMOS logic node. Consequently, we concluded that appropriate strain technologies powerfully improve both carrier transport and LFN property for future CMOS circuits consisting of NW FETs, without any large concern about the interface quality.Dans cette thèse, les propriétés électriques de transistors à nanofils de silicium liées à l'interface oxyde de grille/canal ont été étudiées par le biais de mesures de bruit basse fréquence (bruit 1/f) et de transport dans le canal. Ces transistors nanofils dont les dimensions ont été réduites jusqu'à quelques nanomètres pour la section, représentent une alternative sérieuse pour les futurs nœuds technologiques CMOS. Cependant, la qualité de l'interface oxyde de grille/canal pose question pour transistors dont l'architecture s'étend dans les 3 dimensions, en raison du fort rapport surface/volume inhérent à ces transistors, des différentes orientations cristallographiques de ces interfaces, ou encore des matériaux contraints utilisés pour améliorer les performances électriques. La compréhension des liens entre les propriétés de transport des porteurs dans le canal, qui garantissent en grande partie les performances électriques des transistors, et la qualité de l'interface avec l'oxyde de grille est fond primordiale pour optimiser les transistors nanofils. Les mesures de bruit, associées à l'étude du transport dans le canal, sont un outil puissant et adapté à ces dispositifs tridimensionnels, sans être limité par la taille ultra-réduite des transistors nanofils. Les transistors nanofils étudiés ont été fabriqués à partir de substrats minces SOI, et intègrent un empilement de grille HfSiON/TiN, qui permet de réduire les dimensions tout en conservant les mêmes propriétés électrostatiques. Pour gagner en performances, des contraintes mécaniques ont été introduites dans le canal en silicium : en tension pour les NMOS, par le biais de substrat contraint (sSOI), et en compression pour les PMOS. Un canal en compression uni-axiale peut être obtenu par l'intégration de source/drain en SiGe et/ou par l'utilisation de couches contraintes de type CESL. Des transistors à canal SiGe sur isolant en compression ont également été fabriqués et étudiés. Les caractéristiques électriques des divers transistors nanofils (courbes Id-Vg, compromis Ion-Ioff, mobilité des porteurs) démontrent l'excellent contrôle électrostatique dû à l'architecture 3D, ainsi que l'efficacité de l'ingénierie de contraintes dans les nanofils jusqu'à de faibles longueurs de grilles (~17nm). Des mesures de bruit basse fréquence ont été réalisées sur ces mêmes dispositifs et analysées en fonction des paramètres géométriques de l'architecture nanofils (largeur W, forme de la section, longueur de grille L), et des diverses variantes technologiques. Nous avons démontré que le bruit 1/f dans les transistors nanofils peut être décrit par le modèle de fluctuations du nombre de porteurs (CNF) corrélées aux fluctuations de mobilité (CMF). Le bruit associé aux régions S/D a pu également être intégré dans ce modèle en ajoutant une contribution, en particulier pour les PMOS. Alors que les différentes variantes technologiques ont peu d'effet sur le bruit 1/f, les variations de géométrie en L et W changent la composante de bruit liée aux fluctuations du nombre de porteurs (CNF) de manière inversement proportionnelle à la surface totale (~1/WL). Cette augmentation du bruit est le reflet du transport qui se produit à proximité des interfaces avec l'oxyde. Les différentes orientations des interfaces supérieures et latérales (110) ou (100) présentent la même quantité de pièges d'interface (extrait à partir des mesures de bruit 1/f, en séparant les contributions des différentes faces du nanofil) bien qu'ayant une rugosité différente essentiellement liée au process. En revanche la composante CMF n'est pas altérée par la réduction des dimensions contrairement à la mobilité des porteurs qui décroit fortement avec L. Finalement, les mesures de bruit 1/f ont été comparées aux spécifications ITRS 2013 pour les transistors multi-grilles en vue des futurs nœuds technologiques de la logique CMOS, et démontrent que nos transistors nanofils satisfont les exigences en la matière

Electrical characterization and modeling of low dimensional nanostructure FET

At the beginning of this thesis, basic and advanced device fabrication process which I haveexperienced during study such as top-down and bottom-up approach for the nanoscale devicefabrication technique have been described. Especially, lithography technology has beenfocused because it is base of the modern device fabrication. For the advanced device structure,etching technique has been investigated in detail.The characterization of FET has been introduced. For the practical consideration in theadvanced FET, several parameter extraction techniques have been introduced such as Yfunction,split C-V etc.FinFET is one of promising alternatives against conventional planar devices. Problem ofFinFET is surface roughness. During the fabrication, the etching process induces surfaceroughness on the sidewall surfaces. Surface roughness of channel decreases the effectivemobility by surface roughness scattering. With the low temperature measurement andmobility analysis, drain current through sidewall and top surface was separated. From theseparated currents, effective mobilities were extracted in each temperature conditions. Astemperature lowering, mobility behaviors from the transport on each surface have differenttemperature dependence. Especially, in n-type FinFET, the sidewall mobility has strongerdegradation in high gate electric field compare to top surface. Quantification of surfaceroughness was also compared between sidewall and top surface. Low temperaturemeasurement is nondestructive characterization method. Therefore this study can be a propersurface roughness measurement technique for the performance optimization of FinFET.As another quasi-1 D nanowire structure device, 3D stacked SiGe nanowire has beenintroduced. Important of strain engineering has been known for the effective mobility booster.The limitation of dopant diffusion by strain has been shown. Without strain, SiGe nanowireFET showed huge short channel effect. Subthreshold current was bigger than strained SiGechannel. Temperature dependent mobility behavior in short channel unstrained device wascompletely different from the other cases. Impurity scattering was dominant in short channelunstrained SiGe nanowire FET. Thus, it could be concluded that the strain engineering is notnecessary only for the mobility booster but also short channel effect immunity.Junctionless FET is very recently developed device compare to the others. Like as JFET,junctionless FET has volume conduction. Thus, it is less affected by interface states.Junctionless FET also has good short channel effect immunity because off-state ofjunctionless FET is dominated pinch-off of channel depletion. For this, junctionless FETshould have thin body thickness. Therefore, multi gate nanowire structure is proper to makejunctionless FET.Because of the surface area to volume ratio, quasi-1D nanowire structure is good for thesensor application. Nanowire structure has been investigated as a sensor. Using numericalsimulation, generation-recombination noise property was considered in nanowire sensor.Even though the surface area to volume ration is enhanced in the nanowire channel, devicehas sensing limitation by noise. The generation-recombination noise depended on the channelgeometry. As a design tool of nanowire sensor, noise simulation should be carried out toescape from the noise limitation in advance.The basic principles of device simulation have been discussed. Finite difference method andMonte Carlo simulation technique have been introduced for the comprehension of devicesimulation. Practical device simulation data have been shown for examples such as FinFET,strongly disordered 1D channel, OLED and E-paper.At the beginning of this thesis, basic and advanced device fabrication process which I haveexperienced during study such as top-down and bottom-up approach for the nanoscale devicefabrication technique have been described. Especially, lithography technology has beenfocused because it is base of the modern device fabrication. For the advanced device structure,etching technique has been investigated in detail.The characterization of FET has been introduced. For the practical consideration in theadvanced FET, several parameter extraction techniques have been introduced such as Yfunction,split C-V etc.FinFET is one of promising alternatives against conventional planar devices. Problem ofFinFET is surface roughness. During the fabrication, the etching process induces surfaceroughness on the sidewall surfaces. Surface roughness of channel decreases the effectivemobility by surface roughness scattering. With the low temperature measurement andmobility analysis, drain current through sidewall and top surface was separated. From theseparated currents, effective mobilities were extracted in each temperature conditions. Astemperature lowering, mobility behaviors from the transport on each surface have differenttemperature dependence. Especially, in n-type FinFET, the sidewall mobility has strongerdegradation in high gate electric field compare to top surface. Quantification of surfaceroughness was also compared between sidewall and top surface. Low temperaturemeasurement is nondestructive characterization method. Therefore this study can be a propersurface roughness measurement technique for the performance optimization of FinFET.As another quasi-1 D nanowire structure device, 3D stacked SiGe nanowire has beenintroduced. Important of strain engineering has been known for the effective mobility booster.The limitation of dopant diffusion by strain has been shown. Without strain, SiGe nanowireFET showed huge short channel effect. Subthreshold current was bigger than strained SiGechannel. Temperature dependent mobility behavior in short channel unstrained device wascompletely different from the other cases. Impurity scattering was dominant in short channelunstrained SiGe nanowire FET. Thus, it could be concluded that the strain engineering is notnecessary only for the mobility booster but also short channel effect immunity.Junctionless FET is very recently developed device compare to the others. Like as JFET,junctionless FET has volume conduction. Thus, it is less affected by interface states.Junctionless FET also has good short channel effect immunity because off-state ofjunctionless FET is dominated pinch-off of channel depletion. For this, junctionless FETshould have thin body thickness. Therefore, multi gate nanowire structure is proper to makejunctionless FET.Because of the surface area to volume ratio, quasi-1D nanowire structure is good for thesensor application. Nanowire structure has been investigated as a sensor. Using numericalsimulation, generation-recombination noise property was considered in nanowire sensor.Even though the surface area to volume ration is enhanced in the nanowire channel, devicehas sensing limitation by noise. The generation-recombination noise depended on the channelgeometry. As a design tool of nanowire sensor, noise simulation should be carried out toescape from the noise limitation in advance.The basic principles of device simulation have been discussed. Finite difference method andMonte Carlo simulation technique have been introduced for the comprehension of devicesimulation. Practical device simulation data have been shown for examples such as FinFET,strongly disordered 1D channel, OLED and E-paper.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

Advanced Silicon and Germanium Transistors for Future P-channel MOSFET Applications

Ph.DDOCTOR OF PHILOSOPH

Strain Engineering for Advanced Silicon, Germanium and Germanium-Tin Transistors

Ph.DDOCTOR OF PHILOSOPH

Multi-gate Si nanowire MOSFETs:fabrication, strain engineering and transport analysis

Multi-gate devices e.g. gate-all-around (GAA) Si nanowires and FinFETs are promising can- didates for aggressive CMOS downscaling. Optimum subthreshold slope, immunity against short channel effect and optimized power consumption are the major benefits of such archi- tectures due to higher electrostatic control of the channel. On the other hand, Si nanowires show excellent mechanical properties e.g. yield and fracture strengths of 10±2% and 30±1% in comparison to 3.7% and 4.0% for bulk Si, respectively, a strong motivation to be used as exclusive platforms for innovative nanoelectronic applications e.g. novel strain engineering techniques for carrier transport enhancement in multi-gate 3D suspended channels or lo- cal band-gap modulation using > 4 GPa uniaxial tensile stress in suspended Si channels to enhance the band-to-band tunneling current in multi-gate Tunnel-FETs, all without plastic deformation and therefore, no carrier mobility degradation in deeply scaled channels. In this thesis and as a first step, a precise built-in stress analysis during local thermal oxidation of suspended Si NWs in the presence of a Si3N4 tensile hard mask was done. Accumulation of up to 2.6 GPa uniaxial tensile stress in the buckled NWs is reported. The contribution of hard mask/spacer engineering on the stress level and the NW formation was studied and buckled self-aligned dual NW MOSFETs on bulk Si with two sub-100 nm cross-sectional Si cores including ∼0.8 uniaxial tensile stress are reported. Micro-Raman spectroscopy was widely used in this thesis to measure stress in the buckled NWs on both bulk and SOI substrates. A process flow was designed to make dense array of GAA sub-5 nm cross-sectional Si NWs using a SOI substrate including a high level of stress. The NW stress level can be engineered simply using e.g. metal-gate thin film stress suitable for both NMOS and PMOS devices. Lately, highly and heavily doped architectures with a single-type doping profile from source to drain, called junctionless and accumulation-mode devices, are proposed to significantly simplify the fabrication process, address a few technical limitations e.g. ultra-abrupt junctions in order to fabricate shorter channel length devices. Therefore, in this process flow, a highly doped accumulation-mode was targeted as the operation mechanism. Finally, extensive TCAD device simulation was done on GAA Si NW JL MOSFETs to study the corner effects on the device characteristics, from subthreshold to strong accumulation, report the concept of local volume accumulation/depletion, quantum flat-band voltage, significant bias-dependent series resistance in junctionless MOSFETs and finally, support the experimental data to extract precisely the carrier mobility in sub-5 nm Si NW MOSFETs

Strain-Engineered MOSFETs

This book brings together new developments in the area of strain-engineered MOSFETs using high-mibility substrates such as SIGe, strained-Si, germanium-on-insulator and III-V semiconductors into a single text which will cover the materials aspects, principles, and design of advanced devices, their fabrication and applications. The book presents a full TCAD methodology for strain-engineering in Si CMOS technology involving data flow from process simulation to systematic process variability simulation and generation of SPICE process compact models for manufacturing for yield optimization

Démonstration de l'intérêt des dispositifs multi-grilles auto-alignées pour les noeuds sub-10nm.

Les nombreuses modifications de la structure du transistor bulk ont permis de poursuivre la miniaturisation jusqu'à sa limite aux nœuds 32/28nm. Les technologies actuelles répondent au besoin d'un meilleur contrôle électrostatique en s'ouvrant vers l'industrialisation de transistors complètement dépletés, avec les architectures sur film mince (FDSOI) ou non planaires (TriGate FinFET bulk). Dans ce dernier cas, le substrat bulk reste limitant pour des applications à basse consommation. La combinaison de la technologie SOI et d'une architecture non-planaire conduit aux transistors TriGate sur SOI (ou TGSOI). Nous verrons l'intérêt de ces dispositifs et démontrerons qu'ils sont compatibles avec les techniques de contrainte. On montrera en particulier les améliorations de mobilité et de courants obtenus sur ces dispositifs de largeur inférieure à 15nm. Des simulations montrent également qu'un dispositif TGSOI peut être compatible avec les techniques de modulation de VT. Enfin, nous démontrons la possibilité de fabriquer des dispositifs ultimes à nanofils empilés avec une grille enrobante par une technique innovante de lithographie tridimensionnelle. La conception, la caractérisation physique et les premiers résultats électriques obtenus seront présentés. Ces solutions peuvent répondre aux besoins des nœuds sub-10nm.Changing the bulk transistor structure was sufficient so far to fulfill the scaling needs. The current technologies answer the needs of electrostatics control with the industrialization of fully depleted transistors, with thin-film (FDSOI) or non-planar (TriGate FinFet bulk) technologies. In the latter, bulk substrate is still an issue for low power applications. Combining SOI with multiple-gate structure gives rise to TriGate on SOI (or TGSOI). We will discuss the interest of such devices and will demonstrate their compatibility with strain techniques. We will focus on the mobility and current enhancement obtained on sub-15nm width devices. Simulations also demonstrate the compatibility of TGSOI with VT modulation technique. Finally, we demonstrate the fabrication through 3D lithography of ultimate stacked nanowires with a gate-all-around. The conception, physical characterization and first electrical results are presented.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

Modelling and simulation study of NMOS Si nanowire transistors

Nanowire transistors (NWTs) represent a potential alternative to Silicon FinFET technology in the 5nm CMOS technology generation and beyond. Their gate length can be scaled beyond the limitations of FinFET gate length scaling to maintain superior off-state leakage current and performance thanks to better electrostatic control through the semiconductor nanowire channels by gate-all-around (GAA) architecture. Furthermore, it is possible to stack nanowires to enhance the drive current per footprint. Based on these considerations, vertically-stacked lateral NWTs have been included in the latest edition of the International Technology Roadmap for Semiconductors (ITRS) to allow for further performance enhancement and gate pitch scaling, which are key criteria of merit for the new CMOS technology generation. However, electrostatic confinement and the transport behaviour in these devices are more complex, especially in or beyond the 5nm CMOS technology generation. At the heart of this thesis is the model-based research of aggressively-scaled NWTs suitable for implementation in or beyond the 5nm CMOS technology generation, including their physical and operational limitations and intrinsic parameter fluctuations. The Ensemble Monte Carlo approach with Poisson-Schrödinger (PS) quantum corrections was adopted for the purpose of predictive performance evaluation of NWTs. The ratio of the major to the minor ellipsoidal cross-section axis (cross-sectional aspect ratio - AR) has been identified as a significant contributing factor in device performance. Until now, semiconductor industry players have carried out experimental research on NWTs with two different cross-sections: circular cylinder (or elliptical) NWTs and nanosheet (or nanoslab) NWTs. Each version has its own benefits and drawbacks; however, the key difference between these two versions is the cross-sectional AR. Several critical design questions, including the optimal NWT cross-sectional aspect ratio, remain unanswered. To answer these questions, the AR of a GAA NWT has been investigated in detail in this research maintaining the cross-sectional area constant. Signatures of isotropic charge distributions within Si NWTs were observed, exhibiting the same attributes as the golden ratio (Phi), the significance of which is well-known in the fields of art and architecture. To address the gap in the existing literature, which largely explores NWT scaling using single-channel simulation, thorough simulations of multiple channels vertically-stacked NWTs have been carried out with different cross-sectional shapes and channel lengths. Contact resistance, non-equilibrium transport and quantum confinement effects have been taken into account during the simulations in order to realistically access performance and scalability. Finally, the individual and combined effects of key statistical variability (SV) sources on threshold voltage (VT), subthreshold slope (SS), ON-current (Ion) and drain-induced barrier lowering (DIBL) have been simulated and discussed. The results indicate that the variability of NWTs is impacted by device architecture and dimensions, with a significant reduction in SV found in NWTs with optimal aspect ratios. Furthermore, a reduction in the variability of the threshold voltage has been observed in vertically-stacked NWTs due to the cancelling-out of variability in double and triple lateral channel NWTs

Fabrication, characterization, and modeling of silicon multi-gate devices

Ph.DDOCTOR OF PHILOSOPH

Addressing performance bottlenecks for top-down engineered nanowire transistors

Ph.DDOCTOR OF PHILOSOPH