Cross-Layer Optimization for Power-Efficient and Robust Digital Circuits and Systems

With the increasing digital services demand, performance and power-efficiency become vital requirements for digital circuits and systems. However, the enabling CMOS technology scaling has been facing significant challenges of device uncertainties, such as process, voltage, and temperature variations. To ensure system reliability, worst-case corner assumptions are usually made in each design level. However, the over-pessimistic worst-case margin leads to unnecessary power waste and performance loss as high as 2.2x. Since optimizations are traditionally confined to each specific level, those safe margins can hardly be properly exploited. To tackle the challenge, it is therefore advised in this Ph.D. thesis to perform a cross-layer optimization for digital signal processing circuits and systems, to achieve a global balance of power consumption and output quality. To conclude, the traditional over-pessimistic worst-case approach leads to huge power waste. In contrast, the adaptive voltage scaling approach saves power (25% for the CORDIC application) by providing a just-needed supply voltage. The power saving is maximized (46% for CORDIC) when a more aggressive voltage over-scaling scheme is applied. These sparsely occurred circuit errors produced by aggressive voltage over-scaling are mitigated by higher level error resilient designs. For functions like FFT and CORDIC, smart error mitigation schemes were proposed to enhance reliability (soft-errors and timing-errors, respectively). Applications like Massive MIMO systems are robust against lower level errors, thanks to the intrinsically redundant antennas. This property makes it applicable to embrace digital hardware that trades quality for power savings.Comment: 190 page

Theory, design and application of gradient adaptive lattice filters

SIGLELD:D48933/84 / BLDSC - British Library Document Supply CentreGBUnited Kingdo

Low-Power Design of Digital VLSI Circuits around the Point of First Failure

As an increase of intelligent and self-powered devices is forecasted for our future everyday life, the implementation of energy-autonomous devices that can wirelessly communicate data from sensors is crucial. Even though techniques such as voltage scaling proved to effectively reduce the energy consumption of digital circuits, additional energy savings are still required for a longer battery life. One of the main limitations of essentially any low-energy technique is the potential degradation of the quality of service (QoS). Thus, a thorough understanding of how circuits behave when operated around the point of first failure (PoFF) is key for the effective application of conventional energy-efficient methods as well as for the development of future low-energy techniques. In this thesis, a variety of circuits, techniques, and tools is described to reduce the energy consumption in digital systems when operated either in the safe and conservative exact region, close to the PoFF, or even inside the inexact region. A straightforward approach to reduce the power consumed by clock distribution while safely operating in the exact region is dual-edge-triggered (DET) clocking. However, the DET approach is rarely taken, primarily due to the perceived complexity of its integration. In this thesis, a fully automated design flow is introduced for applying DET clocking to a conventional single-edge-triggered (SET) design. In addition, the first static true-single-phase-clock DET flip-flop (DET-FF) that completely avoids clock-overlap hazards of DET registers is proposed. Even though the correct timing of synchronous circuits is ensured in worst-case conditions, the critical path might not always be excited. Thus, dynamic clock adjustment (DCA) has been proposed to trim any available dynamic timing margin by changing the operating clock frequency at runtime. This thesis describes a dynamically-adjustable clock generator (DCG) capable of modifying the period of the produced clock signal on a cycle-by-cycle basis that enables the DCA technique. In addition, a timing-monitoring sequential (TMS) that detects input transitions on either one of the clock phases to enable the selection of the best timing-monitoring strategy at runtime is proposed. Energy-quality scaling techniques aimat trading lower energy consumption for a small degradation on the QoS whenever approximations can be tolerated. In this thesis, a low-power methodology for the perturbation of baseline coefficients in reconfigurable finite impulse response (FIR) filters is proposed. The baseline coefficients are optimized to reduce the switching activity of the multipliers in the FIR filter, enabling the possibility of scaling the power consumption of the filter at runtime. The area as well as the leakage power of many system-on-chips is often dominated by embedded memories. Gain-cell embedded DRAM (GC-eDRAM) is a compact, low-power and CMOS-compatible alternative to the conventional static random-access memory (SRAM) when a higher memory density is desired. However, due to GC-eDRAMs relying on many interdependent variables, the adaptation of existing memories and the design of future GCeDRAMs prove to be highly complex tasks. Thus, the first modeling tool that estimates timing, memory availability, bandwidth, and area of GC-eDRAMs for a fast exploration of their design space is proposed in this thesis