6T-SRAM 1Mb Design with Test Structures and Post Silicon Validation

abstract: Static random-access memories (SRAM) are integral part of design systems as caches and data memories that and occupy one-third of design space. The work presents an embedded low power SRAM on a triple well process that allows body-biasing control. In addition to the normal mode operation, the design is embedded with Physical Unclonable Function (PUF) [Suh07] and Sense Amplifier Test (SA Test) mode. With PUF mode structures, the fabrication and environmental mismatches in bit cells are used to generate unique identification bits. These bits are fixed and known as preferred state of an SRAM bit cell. The direct access test structure is a measurement unit for offset voltage analysis of sense amplifiers. These designs are manufactured using a foundry bulk CMOS 55 nm low-power (LP) process. The details about SRAM bit-cell and peripheral circuit design is discussed in detail, for certain cases the circuit simulation analysis is performed with random variations embedded in SPICE models. Further, post-silicon testing results are discussed for normal operation of SRAMs and the special test modes. The silicon and circuit simulation results for various tests are presented.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Energy optimization of 6T SRAM cell using low-voltage and high-performance inverter structures

The performance of the cell deteriorates, when static random access memory (SRAM) cell is operated below 1V supply voltage with continuous scale down of the complementary metal oxide semiconductor (CMOS) technology. The conventional 6T, 8T-SRAM cells suffer writeability and read static noise margins (SNM) at low-voltages leads to degradation of cell stability. To improve the cell stability and reduce the dynamic power dissipation at low- voltages of the SRAM cell, we proposed four SRAM cells based on inverter structures with less energy consumption using voltage divider bias current sink/source inverter and NOR/NAND gate using a pseudo-nMOS inverter. The design and implementation of SRAM cell using proposed inverter structures are compared with standard 6T, 8T and ST-11T SRAM cells for different supply voltages at 22-nm CMOS technology exhibit better performance of the cell. The read/write static noise margin of the cell significantly increases due to voltage divider bias network built with larger cell-ratio during read path. The load capacitance of the cell is reduced with minimized switching transitions of the devices during high-to-low and low- to-high of the pull-up and pull-down networks from VDD to ground leads to on an average 54% of dynamic power consumption. When compared with the existing ones, the read/write power of the proposed cells is reduced to 30%. The static power gets reduced by 24% due to stacking of transistors takes place in the proposed SRAM cells as compare to existing ones. The layout of the proposed cells is drawn at a 45-nm technology, and occupies an area of 1.5 times greater and 1.8 times greater as compared with 6T-SRAM cell

Novel High Performance Ultra Low Power Static Random Access Memories (SRAMs) Based on Next Generation Technologies

Title from PDF of title page viewed January 27, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (page 107-120)Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019Next Big Thing Is Surely Small: Nanotechnology Can Bring Revolution. Nanotechnology leads the world towards many new applications in various fields of computing, communication, defense, entertainment, medical, renewable energy and environment. These nanotechnology applications require an energy-efficient memory system to compute and process. Among all the memories, Static Random Access Memories (SRAMs) are high performance memories and occupies more than 50% of any design area. Therefore, it is critical to design high performance and energy-efficient SRAM design. Ultra low power and high speed applications require a new generation memory capable of operating at low power as well as low execution time. In this thesis, a novel 8T SRAM design is proposed that offers significantly faster access time and lowers energy consumption along with better read stability and write ability. The proposed design can be used in the conventional SRAM as well as in computationally intensive applications like neural networks and machine learning classifiers [1]-[4]. Novel 8T SRAM design offers higher energy efficiency, reliability, robustness and performance compared to the standard 6T and other existing 8T and 9T designs. It offers the advantages of a 10T SRAM without the additional area, delay and power overheads of the 10T SRAM. The proposed 8T SRAM would be able to overcome many other limitations of the conventional 6T and other 7T, 8T and 9T designs. The design employs single bitline for the write operation, therefore the number of write drivers are reduced. The defining feature of the proposed 8T SRAM is its hybrid design, which is the combination of two techniques: (i) the utilization of single-ended bitline and (ii) the utilization of virtual ground. The single-ended bitline technique ensures separate read and write operations, which eventually reduces the delay and power consumption during the read and write operations. It's independent read and write paths allow the use of the minimum sized access transistors and aid in a disturb-free read operation. The virtual ground weakens the positive feedback in the SRAM cell and improves its write ability. The virtual ground technique is also used to reduce leakages. The proposed design does not require precharging the bitlines for the read operation, which reduces the area and power overheads of the memory system by eliminating the precharging circuit. The design isolates the storage node from the read path, which improves the read stability. For reliability study, we have investigated the static noise margin (SNM) of the proposed 8T SRAM, for which, we have used two methods – (i) the traditional SNM method with the butterfly curve, (ii) the N-curve method A comparative analysis is performed between the proposed and the existing SRAM designs in terms of area, total power consumption during the read and write operations, and stability and reliability. All these advantages make the proposed 8T SRAM design an ideal candidate for the conventional and computationally intensive applications like machine learning classifier and deep learning neural network. In addition to this, there is need for next generation technologies to design SRAM memory because the conventional CMOS technology is approaching its physical and performance boundaries and as a consequence, becoming incompatible with ultra-low-power applications. Emerging devices such as Tunnel Field Effect Transistor (TFET)) and Graphene Nanoribbon Field Effect Transistor (GNRFET) devices are highly potential candidates to overcome the limitations of MOSFET because of their ability to achieve subthreshold slopes below 60 mV/decade and very low leakage currents [6]-[9]. This research also explores novel TFET and GNRFET based 6T SRAM. The thesis evaluates the standby leakage power in the Tunnel FET (TFET) based 6T SRAM cell for different pull-up, pull-down, and pass-gate transistors ratios (PU: PD: PG) and compared to 10nm FinFET based 6T SRAM designs. It is observed that the 10nm TFET based SRAMs have 107.57%, 163.64%, and 140.44% less standby leakage power compared to the 10nm FinFET based SRAMs when the PU: PD: PG ratios are 1:1:1, 1:5:2 and 2:5:2, respectively. The thesis also presents an analysis of the stability and reliability of sub-10nm TFET based 6T SRAM circuit with a reduced supply voltage of 500mV. The static noise margin (SNM), which is a critical measure of SRAM stability and reliability, is determined for hold, read and write operations of the 6T TFET SRAM cell. The robustness of the optimized TFET based 6T SRAM circuit is also evaluated at different supply voltages. Simulations were done in HSPICE and Cadence tools. From the analysis, it is clear that the main advantage of the TFET based SRAM would be the significant improvement in terms of leakage or standby power consumption. Compared to the FinFET based SRAM the standby leakage power of the T-SRAMs are 107.57%, 163.64%, and 140.44% less for 1:1:1, 1:5:2 and 2:5:2 configurations, respectively. Since leakage/standby power is the primary source of power consumption in the SRAM, and the overall system energy efficiency depends on SRAM power consumption, TFET based SRAM would lead to massive improvement of the energy efficiency of the system. Therefore, T-SRAMs are more suitable for ultra-low power applications. In addition to this, the thesis evaluates the standby leakage power of types of Graphene Nanoribbon FETs based 6T SRAM bitcell and compared to 10nm FinFET based 6T SRAM bitcell. It is observed that the 10nm MOS type GNRFET based SRAMs have 16.43 times less standby leakage power compared to the 10nm FinFET based SRAMs. The double gate SB-GNRFET based SRAM consumes 1.35E+03 times less energy compared to the 10nm FinFET based SRAM during write. However, during read double gate SB-GNRFET based SRAM consume 15 times more energy than FinFET based SRAM. It is also observed that GNRFET based SRAMs are more stable and reliable than FinFET based SRAM.Introduction -- Background -- Novel High Performance Ultra Low Power SRAM Design -- Tunnel FET Based SRAM Design -- Graphene Nanoribbon FET Based SRAM Design -- Double-gate FDSOI Based SRAM Designs -- Novel CNTFET and MEMRISTOR Based Digital Designs -- Conclusio

Ultra-Low Power Circuit Design for Cubic-Millimeter Wireless Sensor Platform.

Modern daily life is surrounded by smaller and smaller computing devices. As Bell’s Law predicts, the research community is now looking at tiny computing platforms and mm3-scale sensor systems are drawing an increasing amount of attention since they can create a whole new computing environment. Designing mm3-scale sensor nodes raises various circuit and system level challenges and we have addressed and proposed novel solutions for many of these challenges to create the first complete 1.0mm3 sensor system including a commercial microprocessor. We demonstrate a 1.0mm3 form factor sensor whose modular die-stacked structure allows maximum volume utilization. Low power I2C communication enables inter-layer serial communication without losing compatibility to standard I2C communication protocol. A dual microprocessor enables concurrent computation for the sensor node control and measurement data processing. A multi-modal power management unit allowed energy harvesting from various harvesting sources. An optical communication scheme is provided for initial programming, synchronization and re-programming after recovery from battery discharge. Standby power reduction techniques are investigated and a super cut-off power gating scheme with an ultra-low power charge pump reduces the standby power of logic circuits by 2-19× and memory by 30%. Different approaches for designing low-power memory for mm3-scale sensor nodes are also presented in this work. A dual threshold voltage gain cell eDRAM design achieves the lowest eDRAM retention power and a 7T SRAM design based on hetero-junction tunneling transistors reduces the standby power of SRAM by 9-19× with only 15% area overhead. We have paid special attention to the timer for the mm3-scale sensor systems and propose a multi-stage gate-leakage-based timer to limit the standard deviation of the error in hourly measurement to 196ms and a temperature compensation scheme reduces temperature dependency to 31ppm/°C. These techniques for designing ultra-low power circuits for a mm3-scale sensor enable implementation of a 1.0mm3 sensor node, which can be used as a skeleton for future micro-sensor systems in variety of applications. These microsystems imply the continuation of the Bell’s Law, which also predicts the massive deployment of mm3-scale computing systems and emergence of even smaller and more powerful computing systems in the near future.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91438/1/sori_1.pd

Power Management and SRAM for Energy-Autonomous and Low-Power Systems

We demonstrate the two first-known, complete, self-powered millimeter-scale computer systems. These microsystems achieve zero-net-energy operation using solar energy harvesting and ultra-low-power circuits. A medical implant for monitoring intraocular pressure (IOP) is presented as part of a treatment for glaucoma. The 1.5mm3 IOP monitor is easily implantable because of its small size and measures IOP with 0.5mmHg accuracy. It wirelessly transmits data to an external wand while consuming 4.7nJ/bit. This provides rapid feedback about treatment efficacies to decrease physician response time and potentially prevent unnecessary vision loss. A nearly-perpetual temperature sensor is presented that processes data using a 2.1μW near-threshold ARM°R Cortex- M3TM μP that provides a widely-used and trusted programming platform. Energy harvesting and power management techniques for these two microsystems enable energy-autonomous operation. The IOP monitor harvests 80nW of solar power while consuming only 5.3nW, extending lifetime indefinitely. This allows the device to provide medical information for extended periods of time, giving doctors time to converge upon the best glaucoma treatment. The temperature sensor uses on-demand power delivery to improve low-load dc-dc voltage conversion efficiency by 4.75x. It also performs linear regulation to deliver power with low noise, improved load regulation, and tight line regulation. Low-power high-throughput SRAM techniques help millimeter-scale microsystems meet stringent power budgets. VDD scaling in memory decreases energy per access, but also decreases stability margins. These margins can be improved using sizing, VTH selection, and assist circuits, as well as new bitcell designs. Adaptive Crosshairs modulation of SRAM power supplies fixes 70% of parametric failures. Half-differential SRAM design improves stability, reducing VMIN by 72mV. The circuit techniques for energy autonomy presented in this dissertation enable millimeter-scale microsystems for medical implants, such as blood pressure and glucose sensors, as well as non-medical applications, such as supply chain and infrastructure monitoring. These pervasive sensors represent the continuation of Bell’s Law, which accurately traces the evolution of computers as they become smaller, more numerous, and more powerful. The development of millimeter-scale massively-deployed ubiquitous computers ensures the continued expansion and profitability of the semiconductor industry. NanoWatt circuit techniques will allow us to meet this next frontier in IC design.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/86387/1/grgkchen_1.pd

ENERGY-EFFICIENT FEATURE EXTRACTION ENGINE AND SECURE CHIP IDENTIFICATION FOR UBIQUITOUS SURVEILLANCE

Ph.DDOCTOR OF PHILOSOPH

Design and analysis of SRAMs for energy harvesting systems

PhD ThesisAt present, the battery is employed as a power source for wide varieties of microelectronic systems ranging from biomedical implants and sensor net-works to portable devices. However, the battery has several limitations and incurs many challenges for the majority of these systems. For instance, the design considerations of implantable devices concern about the battery from two aspects, the toxic materials it contains and its lifetime since replacing the battery means a surgical operation. Another challenge appears in wire-less sensor networks, where hundreds or thousands of nodes are scattered around the monitored environment and the battery of each node should be maintained and replaced regularly, nonetheless, the batteries in these nodes do not all run out at the same time. Since the introduction of portable systems, the area of low power designs has witnessed extensive research, driven by the industrial needs, towards the aim of extending the lives of batteries. Coincidentally, the continuing innovations in the field of micro-generators made their outputs in the same range of several portable applications. This overlap creates a clear oppor-tunity to develop new generations of electronic systems that can be powered, or at least augmented, by energy harvesters. Such self-powered systems benefit applications where maintaining and replacing batteries are impossi-ble, inconvenient, costly, or hazardous, in addition to decreasing the adverse effects the battery has on the environment. The main goal of this research study is to investigate energy harvesting aware design techniques for computational logic in order to enable the capa- II bility of working under non-deterministic energy sources. As a case study, the research concentrates on a vital part of all computational loads, SRAM, which occupies more than 90% of the chip area according to the ITRS re-ports. Essentially, this research conducted experiments to find out the design met-ric of an SRAM that is the most vulnerable to unpredictable energy sources, which has been confirmed to be the timing. Accordingly, the study proposed a truly self-timed SRAM that is realized based on complete handshaking protocols in the 6T bit-cell regulated by a fully Speed Independent (SI) tim-ing circuitry. The study proved the functionality of the proposed design in real silicon. Finally, the project enhanced other performance metrics of the self-timed SRAM concentrating on the bit-line length and the minimum operational voltage by employing several additional design techniques.Umm Al-Qura University, the Ministry of Higher Education in the Kingdom of Saudi Arabia, and the Saudi Cultural Burea

Low energy digital circuit design using sub-threshold operation

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, February 2006.Includes bibliographical references (p. 189-202).Scaling of process technologies to deep sub-micron dimensions has made power management a significant concern for circuit designers. For emerging low power applications such as distributed micro-sensor networks or medical applications, low energy operation is the primary concern instead of speed, with the eventual goal of harvesting energy from the environment. Sub-threshold operation offers a promising solution for ultra-low-energy applications because it often achieves the minimum energy per operation. While initial explorations into sub-threshold circuits demonstrate its promise, sub-threshold circuit design remains in its infancy. This thesis makes several contributions that make sub-threshold design more accessible to circuit designers. First, a model for energy consumption in sub-threshold provides an analytical solution for the optimum VDD to minimize energy. Fitting this model to a generic circuit allows easy estimation of the impact of processing and environmental parameters on the minimum energy point. Second, analysis of device sizing for sub-threshold circuits shows the trade-offs between sizing for minimum energy and for minimum voltage operation.(cont.) A programmable FIR filter test chip fabricated in 0.18pum bulk CMOS provides measurements to confirm the model and the sizing analysis. Third, a low-overhead method for integrating sub-threshold operation with high performance applications extends dynamic voltage scaling across orders of magnitude of frequency and provides energy scalability down to the minimum energy point. A 90nm bulk CMOS test chip confirms the range of operation for ultra-dynamic voltage scaling. Finally, sub-threshold operation is extended to memories. Analysis of traditional SRAM bitcells and architectures leads to development of a new bitcell for robust sub-threshold SRAM operation. The sub-threshold SRAM is analyzed experimentally in a 65nm bulk CMOS test chip.by Benton H. Calhoun.Ph.D

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”