Architectures for RF Frequency synthesizers

Frequency synthesizers are an essential building block of RF communication products. They can be found in traditional consumer products, in personal communication systems, and in optical communication equipment. Since frequency synthesizers are used in many different applications, different performance aspects may need to be considered in each case. The main body of the text describes a conceptual framework for analyzing the performance of PLL frequency synthesizers, and presents optimization procedures for the different performance aspects. The analysis of the PLL properties is performed with the use of the open-loop bandwidth and phase margin concepts, to enable the influence of higher-order poles to be taken into account from the beginning of the design process. The theoretical system analysis is complemented by descriptions of innovative system and building block architectures, by circuit implementations in bipolar and CMOS technologies, and by measurement results. Architectures for RF Frequency Synthesizers contains basic information for the beginner as well as in-depth knowledge for the experienced designer. It is widely illustrated with practical design examples used in industrial products.\ud Written for:\ud Electrical and electronic engineer

Theory, design and implementation of an IF cancellation module for use in a stepped frequency continuous wave ground penetrating radar

Bibliography: leaves 64-68.A device has been designed that cancels the leakage signal between the transmit and receive antenna in a Stepped Frequency Continuous Wave Ground Penetrating Radar. The front end of the radar operates at high signal levels and, as a result, a large signal is coupled directly from the transmit to the receive antenna. This signal uses a signiï¬ cant part of the dynamic range of the data-capturing device, an analogue-to-digital converter (ADC). The objective of this cancellation is thus to increase the effective instantaneous dynamic range of the radar system. Simulations show that 10-bit amplitude and phase resolution in the digital cancellation circuit would achieve maximum cancellation in the presence of phase noise and other sources of error. This result is conï¬ rmed when the hardware is tested. The device was constructed and operates as intended. Tests show that cancellation exceeding 53dBm is possible through careful calibration. It was concluded that the device could successfully be integrated into the SFCW GPR and that it would achieve an increase in the instantaneous dynamic range

Method and apparatus for spur-reduced digital sinusoid synthesis

A technique for reducing the spurious signal content in digital sinusoid synthesis is presented. Spur reduction is accomplished through dithering both amplitude and phase values prior to word-length reduction. The analytical approach developed for analog quantization is used to produce new bounds on spur performance in these dithered systems. Amplitude dithering allows output word-length reduction without introducing additional spurs. Effects of periodic dither similar to that produced by a pseudo-noise (PN) generator are analyzed. This phase dithering method provides a spur reduction of 6(M + 1) dB per phase bit when the dither consists of M uniform variates. While the spur reduction is at the expense of an increase in system noise, the noise power can be made white, making the power spectral density small. This technique permits the use of a smaller number of phase bits addressing sinusoid look-up tables, resulting in an exponential decrease in system complexity. Amplitude dithering allows the use of less complicated multipliers and narrower data paths in purely digital applications, as well as the use of coarse-resolution, highly-linear digital-to-analog converters (DAC's) to obtain spur performance limited by the DAC linearity rather than its resolution

Integrated radio frequency synthetizers for wireless applications

This thesis consists of six publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis concentrates on the design of phase-locked loop radio frequency synthesizers for wireless applications. In particular, the focus is on the implementation of the prescaler, the phase detector, and the chargepump. This work reviews the requirements set for the frequency synthesizer by the wireless standards, and how these requirements are derived from the system specifications. These requirements apply to both integer-N and fractional-N synthesizers. The work also introduces the special considerations related to the design of fractional-N phase-locked loops. Finally, implementation alternatives for the different building blocks of the synthesizer are reviewed. The presented work introduces new topologies for the phase detector and the chargepump, and improved topologies for high speed CMOS prescalers. The experimental results show that the presented topologies can be successfully used in both integer-N and fractional-N synthesizers with state-of-the-art performance. The last part of this work discusses the additional considerations that surface when the synthesizer is integrated into a larger system chip. It is shown experimentally that the synthesizer can be successfully integrated into a complex transceiver IC without sacrificing the performance of the synthesizer or the transceiver.reviewe

End-to-End Direct Digital Synthesis Simulation and Mathematical Model to Minimize Quantization Effects of Digital Signal Generation

Direct digital synthesis (DDS) architectures are becoming more prevalent as modern digital-to-analog converter (DAC) and programmable logic devices evolve to support higher bandwidths. The DDS architecture provides the benefit of digital control but at a cost of generating spurious content in the spectrum. The generated spurious content may cause intermodulation distortion preventing proper demodulation of the received signal. The distortion may also interfere with the neighboring frequency bands. This article presents the various DDS architectures and explores the DDS architecture which provides the most digital reconfigurability with the lowest spurious content. End-to-end analytical equations, numerical and mathematical models are developed to determine the location and power levels of spurs. Afterwards, the analytical equations, numerical and mathematical models are shown to be consistent with the experimental data. A developer can use the information to design a DDS architecture that meets their minimum requirements

Spur-reduced digital sinusoid synthesis

This article presents and analyzes a technique for reducing the spurious signal content in digital sinusoid synthesis. Spurious-harmonic (spur) reduction is accomplished through dithering both amplitude and phase values prior to word-length reduction. The analytical approach developed for analog quantization is used to produce new bounds on spur performance in these dithered systems. Amplitude dithering allows output word-length reduction without introducing additional spurs. Effects of periodic dither similar to those produced by a pseudonoise (PN) generator are analyzed. This phase-dithering method provides a spur reduction of 6(M plus one) dB per phase bit when the dither consists of M uniform variates. While the spur reduction is at the expense of an increase in system noise, the noise power can be made white, making the power spectral density small. This technique permits the use of a smaller number of phase bits addressing sinusoid lookup tables, resulting in an exponential decrease in system complexity. Amplitude dithering allows the use of less complicated multipliers and narrower data paths in purely digital applications, as well as the use of coarse resolution, highly linear digital to analog converters (DAC's) to obtain spur performance limited by the DAC linearity rather than its resolution

Programmable rate modem utilizing digital signal processing techniques

The engineering development study to follow was written to address the need for a Programmable Rate Digital Satellite Modem capable of supporting both burst and continuous transmission modes with either binary phase shift keying (BPSK) or quadrature phase shift keying (QPSK) modulation. The preferred implementation technique is an all digital one which utilizes as much digital signal processing (DSP) as possible. Here design tradeoffs in each portion of the modulator and demodulator subsystem are outlined, and viable circuit approaches which are easily repeatable, have low implementation losses and have low production costs are identified. The research involved for this study was divided into nine technical papers, each addressing a significant region of concern in a variable rate modem design. Trivial portions and basic support logic designs surrounding the nine major modem blocks were omitted. In brief, the nine topic areas were: (1) Transmit Data Filtering; (2) Transmit Clock Generation; (3) Carrier Synthesizer; (4) Receive AGC; (5) Receive Data Filtering; (6) RF Oscillator Phase Noise; (7) Receive Carrier Selectivity; (8) Carrier Recovery; and (9) Timing Recovery

Ultra Low-Power Frequency Synthesizers for Duty Cycled IoT radios

Internet of Things (IoT), which is one of the main talking points in the electronics industry today, consists of a number of highly miniaturized sensors and actuators which sense the physical environment around us and communicate that information to a central information hub for further processing. This agglomeration of miniaturized sensors helps the system to be deployed in previously impossible arenas such as healthcare (Body Area Networks - BAN), industrial automation, real-time monitoring environmental parameters and so on; thereby greatly improving the quality of life. Since the IoT devices are usually untethered, their energy sources are limited (typically battery powered or energy scavenging) and hence have to consume very low power. Today's IoT systems employ radios that use communication protocols like Bluetooth Smart; which means that they communicate at data rates of a few hundred kb/s to a few Mb/s while consuming around a few mW of power. Even though the power dissipation of these radios have been decreasing steadily over the years, they seem to have reached a lower limit in the recent times. Hence, there is a need to explore other avenues to further reduce this dissipation so as to further improve the energy autonomy of the IoT node. Duty cycling has emerged as a promising alternative in this sense since it involves radios transmitting very short bursts of data at high rates and being asleep the rest of the time. In addition, high data rates proffer the added advantage of reducing network congestion which has become a major problem in IoT owing to the increase in the number of sensor nodes as well as the volume of data they send. But, as the average power (energy) dissipated decreases due to duty cycling, the energy overhead associated with the start-up phase of the radio becomes comparable with the former. Therefore, in order to take full advantage of duty cycling, the radio should be capable of being turned ON/OFF almost instantaneously. Furthermore, the radio of the future should also be able to support easy frequency hopping to improve the system efficiency from an interference point of view. In other words, in addition to high data rate capability, the next generation radios must also be highly agile and have a low energy overhead. All these factors viz. data rate, agility and overhead are mainly dependent on the radio's frequency synthesizer and therefore emphasis needs to be laid on developing new synthesizer architectures which are also amenable to technology scaling. This thesis deals with the evolution of one such all-digital frequency synthesizer; with each step dealing with one of the aforementioned issues. In order to reduce the energy overhead of the synthesizer, FBAR resonators (which are a class of MEMS resonators) are used as the frequency reference instead of a traditional quartz crystal. The FBAR resonators aid the design of fast-startup oscillators as opposed to the long latency associated with the start-up of the crystal oscillator. In addition, the frequency stability of the FBAR lends itself to open-loop architecture which can support very high data rates. Another advantage of the open-loop architecture is the frequency agility which aids easy channel switching for multi-hop architectures, as demonstrated in this thesis