Micro systems technology

The emerging field of Micro Systems Technology is described. Micro Systems Technology can be seen as the meeting of disciplines, a product of convergence along different lines. Apart from the traditional and ever developing line of 'classical' precision engineering, there is a line along micro electronics, micro sensors and actuators. This is the line we focus on in this contribution. The third line worth mentioning is the one along the upcoming field of molecular engineering. The main purpose of this paper is to show the wealth of possibilities and consequently the need for 'integral design' management

A high speed Tri-Vision system for automotive applications

Purpose: Cameras are excellent ways of non-invasively monitoring the interior and exterior of vehicles. In particular, high speed stereovision and multivision systems are important for transport applications such as driver eye tracking or collision avoidance. This paper addresses the synchronisation problem which arises when multivision camera systems are used to capture the high speed motion common in such applications. Methods: An experimental, high-speed tri-vision camera system intended for real-time driver eye-blink and saccade measurement was designed, developed, implemented and tested using prototype, ultra-high dynamic range, automotive-grade image sensors specifically developed by E2V (formerly Atmel) Grenoble SA as part of the European FP6 project – sensation (advanced sensor development for attention stress, vigilance and sleep/wakefulness monitoring). Results : The developed system can sustain frame rates of 59.8 Hz at the full stereovision resolution of 1280 × 480 but this can reach 750 Hz when a 10 k pixel Region of Interest (ROI) is used, with a maximum global shutter speed of 1/48000 s and a shutter efficiency of 99.7%. The data can be reliably transmitted uncompressed over standard copper Camera-Link® cables over 5 metres. The synchronisation error between the left and right stereo images is less than 100 ps and this has been verified both electrically and optically. Synchronisation is automatically established at boot-up and maintained during resolution changes. A third camera in the set can be configured independently. The dynamic range of the 10bit sensors exceeds 123 dB with a spectral sensitivity extending well into the infra-red range. Conclusion: The system was subjected to a comprehensive testing protocol, which confirms that the salient requirements for the driver monitoring application are adequately met and in some respects, exceeded. The synchronisation technique presented may also benefit several other automotive stereovision applications including near and far-field obstacle detection and collision avoidance, road condition monitoring and others.Partially funded by the EU FP6 through the IST-507231 SENSATION project.peer-reviewe

The integration of on-line monitoring and reconfiguration functions using IEEE1149.4 into a safety critical automotive electronic control unit.

This paper presents an innovative application of IEEE 1149.4 and the integrated diagnostic reconfiguration (IDR) as tools for the implementation of an embedded test solution for an automotive electronic control unit, implemented as a fully integrated mixed signal system. The paper describes how the test architecture can be used for fault avoidance with results from a hardware prototype presented. The paper concludes that fault avoidance can be integrated into mixed signal electronic systems to handle key failure modes

Advanced sensors technology survey

This project assesses the state-of-the-art in advanced or 'smart' sensors technology for NASA Life Sciences research applications with an emphasis on those sensors with potential applications on the space station freedom (SSF). The objectives are: (1) to conduct literature reviews on relevant advanced sensor technology; (2) to interview various scientists and engineers in industry, academia, and government who are knowledgeable on this topic; (3) to provide viewpoints and opinions regarding the potential applications of this technology on the SSF; and (4) to provide summary charts of relevant technologies and centers where these technologies are being developed

A review of miniaturised Non-Destructive Testing technologies for in-situ inspections

Non-destructive testing (NDT) techniques have become attractive trends of product manufacturing, installation and post-maintenance in the aerospace, automotive and manufacturing industry, because of its benefits such as cost saving, easy to use and high efficiency etc. With the industrial products becoming large-scale, high integration and complication, developing the NDT miniaturisation technique for in-situ inspections is highly demanded and becoming an inevitable trend. However, in-situ inspection using NDT have been limited by a number of factors, such as the heavy weight, large size or complex structure etc. This paper aims to systematically identify and analyse the current state-of-the-art of NDT miniaturisation techniques in research and innovation, and discuss the challenge and prospect of miniaturisation of the commonly used NDT techniques