SNR-based evaluation of coexistence in wireless system of hospital

Abstract. The wireless system (IEEE Std. 802.11) of North Karelian Central Hospital (NKCH) has been studied in the newly opened J2 building of the hospital. The measurements have been carried out using Ekahau Sidekick spectrum analyser and Ekahau Pro software. Signal propagation has been modelled in the control ward of the Emergency department because many coexisting systems are used with critical requirements of data communication over there. The analytical models have been developed to understand the radio-frequency (RF) signal propagation in the entire building. Measurements have also been carried out on the entire first floor, in the Department of the Abdominal Diseases on the ground floor and in the Children’s wards on the third floor. The multi-slope path-loss propagation models with shadowing have been generated based on the Received Signal Strength Indicator (RSSI) measurements for typical hospital environment at the 2.4 GHz and 5 GHz Industrial, Scientific, and Medical (ISM) band. The measurements have been carried out within the two predefined routes. The models have also been compared to the empirically derived path-loss models. The probability of signal outage has been calculated for both measured routes. The aggregate interference has been measured within the routes that cover the area where remarkable signal variations and the high level of interference has been indicated based on the heatmaps of Ekahau. The use of Ekahau Sidekick and Ekahau Pro software in the coexistence study has been described. The noise floor has been determined based on the averaged values of the six measurement campaigns. The local changes in signal strength of the desired signal and aggregated power of interference have been studied. The Signal-to-Interference Ratio (SIR) models have been generated within the measured routes. The rapid decreases of Signal-to-Noise Ratio (SNR) have been indicated on all measured floors of building J2. They have been studied and their effect on the network performance has been evaluated. The evaluation has been done by comparing the measured values of RSSI, SNR and SIR to the requirements of the respective Modulation and Coding Scheme (MCS). The link margins have been calculated based on the chosen bit error probability and the given SNR requirement of the respective MCS. The comparison between the measured RSSI readings and the required threshold of the respective MCS has been done using the defined shadowing as a link margin. It has been shown that the measured difference between the signal strength of the 2.4 GHz and 5 GHz bands has been caused by the reduced transmit power at the 2.4 GHz band. Based on the SIR measurements, it has been shown that the access points of the neighbouring building have contributed locally to the measured aggregate interference in the Control ward. However, the primary reason for the decrease of SIR at the 2.4 GHz band has been the decrease of desired signal power that has been contributed by the above mentioned reduced transmit power. The strong SNR drops have been indicated on every measured floor before the roaming has occurred.Sairaalan langattoman järjestelmän arviointi signaali-kohina-suhteen avulla. Tiivistelmä. Tässä diplomityössä on tutkittu Pohjois-Karjalan keskussairaalan (PKKS) langatonta verkkoa (IEEE Std. 802.11) äskettäin avatussa sairaalan laajennusosassa (J2-rakennus). Mittaukset on toteutettu käyttäen Ekahau Sidekick spektrianalysaattoria ja Ekahau Pro -ohjelmaa. Päivystyksen valvontaosasto on valittu tutkimuskohteeksi, koska siellä käytetään paljon eri teknologioihin perustuvia järjestelmiä, joiden välinen tiedonsiirto on luonteeltaan kriittistä. Luotujen mallien avulla rakennuksen langatonta toimintaympäristöä tutkitaan RF-järjestelmän (Radio-Frequency) näkökulmasta myös muissa mittausten kohteina olleissa tiloissa. Mittauksia on tehty myös valvontaosaston ulkopuolella 1. kerroksessa sekä 3. kerroksen lastenosastoilla ja Vatsakeskuksen tiloissa pohjakerroksessa. RSSI-mittausten perusteella on luotu radiotiehäviöihin perustuvat etenemismallit molemmilla käytössä olevilla ISM-taajuuskaistoilla (Industrial, Scientific and Medical bands). Varjostuminen ja etenemishäviökertoimen muutokset on otettu huomioon etenemismalleissa. Mittaukset on suoritettu ennalta määritellyillä reiteillä. Luotuja malleja on verrattu myös tutkimuskirjallisuudessa esitettyihin, empiirisesti johdettuihin etenemishäviömalleihin. Signaalikatkoksen todennäköisyys on laskettu molemmille reiteille 2.4 GHz:n taajuuskaistalla. Vastaanotetun häiriötehon summa on mitattu koko mallinnettavan tilan alueelle ulottuvien mittausreittien pohjalta. Mittausreitit on määritelty Ekahau Pron tuottamien kuuluvuus- ja häiriökarttojen avulla ottaen huomioon havaitut signaalitason vaihtelut. Ekahau Sidekick -spektrianalysaattorin ja Ekahau Pro -ohjelman käyttöä on kuvattu tämän tutkimuksen kontekstissa. Kohinataso on määritelty kaikissa kuudessa mittauskampanjassa mitattujen kohina-tehoarvojen keskiarvona. Paikallisten hyötysignaalinvoimakkuus- ja häiriötehovaihteluiden vaikutusta verkon suorituskykyyn on tutkittu ja molemmat mittausreitit kattavat SIR-mallit (Signal-to-Interference Ratio) on luotu. Kaikissa tutkituissa kerroksissa havaittuja äkillisiä signaali-kohinasuhteen vaihteluita on tutkittu ja niiden vaikutusta järjestelmän suorituskykyyn on arvioitu. Mitattujen hyöty- ja häiriösignaalivaihteluiden arviointi on toteutettu vertaamalla mittaamalla saatuja SNR- (Signal-to-Noise ratio), SIR- ja RSSI-arvoja (Received Signal Strength Indicator) eri tiedonsiirtonopeuksia käyttävien MCS-indeksien vaatimiin signaalinvoimakkuus- ja signaali-kohina-suhteen arvoihin. Kynnysarvoille on laskettu linkkimarginaalit käyttäen mitoitusvaatimuksena valittua bittivirhetodennäköisyyden arvoa. Mitattuja RSSI-arvoja on verrattu käyttäen linkkimarginaalina etenemismallinnuksessa määritettyjä varjostumisvaikutuksen arvoja. 2.4 ja 5 GHz:n taajuusalueiden välillä mitatun signaalinvoimakkuuseron on tutkimuksessa saatujen tulosten perusteella osoitettu olevan seurausta alennetusta lähetystehosta 2.4 GHz:n kaistalla. SIR-mittausten perusteella on todettu viereisen rakennuksen tukiasemien kasvattaneen vastaanotettua häiriötehosummaa valvontaosastolla paikallisesti. Ensisijainen syy mitattuihin SIR-arvojen vaihteluihin ovat kuitenkin alhainen signaalinvoimakkuus 2.4 GHz:n kaistalla, mikä osittain johtuu edellä kuvatusta alennetusta lähetystehosta. Voimakkaita SNR-vaihteluita on mitattu kaikissa kerroksissa ennen kuin päätelaite kytkeytyy uuteen tukiasemaan

Power-efficient current-mode analog circuits for highly integrated ultra low power wireless transceivers

In this thesis, current-mode low-voltage and low-power techniques have been applied to implement novel analog circuits for zero-IF receiver backend design, focusing on amplification, filtering and detection stages. The structure of the thesis follows a bottom-up scheme: basic techniques at device level for low voltage low power operation are proposed in the first place, followed by novel circuit topologies at cell level, and finally the achievement of new designs at system level. At device level the main contribution of this work is the employment of Floating-Gate (FG) and Quasi-Floating-Gate (QFG) transistors in order to reduce the power consumption. New current-mode basic topologies are proposed at cell level: current mirrors and current conveyors. Different topologies for low-power or high performance operation are shown, being these circuits the base for the system level designs. At system level, novel current-mode amplification, filtering and detection stages using the former mentioned basic cells are proposed. The presented current-mode filter makes use of companding techniques to achieve high dynamic range and very low power consumption with for a very wide tuning range. The amplification stage avoids gain bandwidth product achieving a constant bandwidth for different gain configurations using a non-linear active feedback network, which also makes possible to tune the bandwidth. Finally, the proposed current zero-crossing detector represents a very power efficient mixed signal detector for phase modulations. All these designs contribute to the design of very low power compact Zero-IF wireless receivers. The proposed circuits have been fabricated using a 0.5μm double-poly n-well CMOS technology, and the corresponding measurement results are provided and analyzed to validate their operation. On top of that, theoretical analysis has been done to fully explore the potential of the resulting circuits and systems in the scenario of low-power low-voltage applications.Programa Oficial de Doctorado en Tecnologías de las Comunicaciones (RD 1393/2007)Komunikazioen Teknologietako Doktoretza Programa Ofiziala (ED 1393/2007

Low-Power Pıc-Based Sensor Node Devıce Desıgn And Theoretıcal Analysıs Of Energy Consumptıon In Wıreless Sensor Networks

Teknolojinin ilerlemesi, daha enerji verimli ve daha ucuz elektronik bileşenlerinin daha küçük üretilmesini sağlamıştır. Bu nedenle, daha önce mevcut birçok bilgisayar ve elektronik bilim-mühendislik fikirleri uygulanabilir hale gelmiştir. Bunlardan birisi de kablosuz sensör ağları teknolojisidir. Kablosuz algılayıcı ağlar, düşük enerji tüketimi ve gerekli teknik gereksinimlerin gerçekleşmesi ile uygulanabilir hale gelmiştir. Ayrıca, Kablosuz algılayıcı ağlarının tasarımında iletişim algoritmaları, enerji tasarruf protokolleri ve yenilenebilir enerji teknolojileri gibi diğer bilimsel çalışmalar zorunlu hale gelmiştir. Bu tez, mikroelektronik sistemler, kablosuz iletişim ve dijital elektronik teknolojisinin ilerlemesiyle uygulanabilir hale gelmiş sensör ağları teknolojisini kapsamaktadır. Birincisi, algılama görevleri ve potansiyel algılayıcı ağ uygulamaları araştırılmış ve algılayıcı ağlarının tasarımını etkileyen faktörlerin gözden geçirilmesi sağlanmıştır. Ardından sensör ağları için iletişim mimarisi ana hatlarıyla belirtilmiştir. Ayrıca, tek bir düğümün WLAN ile iletişim kurabilmesi için yeni donanım mimarisi tasarlanmış ve düğümlerde yenilenebilir enerji kaynakları kullanılmıştır. Bu tezde WSN, analitik bilim ve uygulamalı bilim açısından incelenmiştir. Düşük enerji tüketimi ve iletişim protokolleri arasındaki ilişki değerlendirilmiş ve bilimsel sonuçlara varılmıştır. Teorik analizler bilimsel uygulamalarla desteklenmiştir. Çalışmalar, düşük enerji ve maksimum verimlilik prensibinin gerçekleştirilmesine dayalı kablosuz sensör ağları üzerinde gerçekleştirilmiştir. Kablosuz sensör ağlari sistemi tasarlandıktan sonra; sensör düğümlerinin enerji tüketimi ve kablosuz ağdaki davranışları test ve analiz edilmiştir. Düşük enerji tüketimi ile sensör düğümleri arasındaki ilişki detaylı olarak değerlendirilmiştir. PIC Tabanlı mikro denetleyiciler sensör düğümlerinin tasarımında kullanılmış ve çok düşük maliyetli tasarım için ultra düşük güçte, nanoWatt teknolojisi ile desteklenen sensör düğümleri tasarlanmıştır. İşleme birimi, bellek birimi ve kablosuz iletişim birimi sensör viii düğümlerine entegre edilmiştir. Tasarlanan sensör düğümünün işletim sistemi PIC C dili ile yazılmıştır ve PIC işletim sistemi nem, sıcaklık, ışığa duyarlılık ve duman sensörü gibi farklı özelliklerin ölçülmesine izin vermiştir. Sensörlerden gelen verilerin merkezi bir konumdan kaydedilmesi ve izlenebilmesi için, C# programlama dili ile bilgisayar yazılımı geliştirilmiştir. Gelişmiş algılayıcı düğümler tarafından alınan kararların uygulanması için yazılım algoritması ve donanım modüllerini içeren karar verme sistemi tasarlanmıştır. Gelişmiş PIC Tabanlı sensör düğümleri, enerji üretimi ve enerji tasarrufu için, güneş enerjisi paneli, şarj edilebilir pil ve süper kapasitör gibi yenilenebilir enerji kaynakları ile benzersiz bir PIC Kontrollü voltaj birimi ile desteklenmiştir. Geliştirilmiş kablosuz sensör ağları sistemi, endüstri uygulamaları, akıllı fabrikalar ve akıllı evler gibi günlük hayat uygulamaları için de kullanılabilecektir. Kablosuz algılayıcı ağlar geniş bir aralıkta kullanılmak üzere tasarlanmıştır. Tezin sonuçları, özellikle yenilenebilir enerji kaynakları ile WSN'nin geliştirilmesine yardımcı olmayı amaçlamaktadır

Ground, Proximal, and Satellite Remote Sensing of Soil Moisture

Soil moisture (SM) is a key hydrologic state variable that is of significant importance for numerous Earth and environmental science applications that directly impact the global environment and human society. Potential applications include, but are not limited to, forecasting of weather and climate variability; prediction and monitoring of drought conditions; management and allocation of water resources; agricultural plant production and alleviation of famine; prevention of natural disasters such as wild fires, landslides, floods, and dust storms; or monitoring of ecosystem response to climate change. Because of the importance and wide‐ranging applicability of highly variable spatial and temporal SM information that links the water, energy, and carbon cycles, significant efforts and resources have been devoted in recent years to advance SM measurement and monitoring capabilities from the point to the global scales. This review encompasses recent advances and the state‐of‐the‐art of ground, proximal, and novel SM remote sensing techniques at various spatial and temporal scales and identifies critical future research needs and directions to further advance and optimize technology, analysis and retrieval methods, and the application of SM information to improve the understanding of critical zone moisture dynamics. Despite the impressive progress over the last decade, there are still many opportunities and needs to, for example, improve SM retrieval from remotely sensed optical, thermal, and microwave data and opportunities for novel applications of SM information for water resources management, sustainable environmental development, and food security

Development of the future generation of smart high voltage connectors and related components for substations, with energy autonomy and wireless data transmission capability

The increased dependency on electricity of modern society, makes reliability of power transmission systems a key point. This goal can be achieved by continuously monitoring power grid parameters, so possible failure modes can be predicted beforehand. It can be done using existing Information and Communication Technologies (ICT) and Internet of Things (10T) technologies that include instrumentation and wireless communication systems, thus forming a wireless sensor network (WSN). Electrical connectors are among the most critical parts of any electrical system and hence, they can act as nodes of such WSN. Therefore, the fundamental objective of this thesis is the design, development and experimental validation of a self-powered IOT solution for real-time monitoring of the health status of a high-voltage substation connector and related components of the electrical substation. This new family of power connectors is called SmartConnector and incorporates a thermal energy harvesting system powering a microcontroller that controls a transmitter and several electronic sensors to measure the temperature, current and the electrical contact resistance (ECR) of the connector. These measurements are sent remotely via a Bluetooth 5 wireless communication module to a local gateway, which further transfers the measured data to a database server for storage as well as further analysis and visualization. By this way, after suitable data processing, the health status of the connector can be available in real-time, allowing different appealing functions, such as assessing the correct installation of the connector, the current health status or its remaining useful life (RUL) in real-time. The same principal can also be used for other components of substation like spacers, insulators, conductors, etc. Hence, to prove universality of this novel approach, a similar strategy is applied to a spacer which is capable of measuring uneven current distribution in three closely placed conductors. This novel IOT device is called as SmartSpacer. Care has to be taken that this technical and scientific development has to be compatible with existing substation bus bars and conductors, and especially to be compatible with the high operating voltages, i.e., from tens to hundreds of kilo-Volts (kV), and with currents in the order of some kilo-pm peres (kA). Although some electrical utilities and manufacturers have progressed in the development of such technologies, including smart meters and smart sensors, electrical device manufacturers such as of substation connectors manufacturers have not yet undertaken the technological advancement required for the development of such a new family of smart components involved in power transmission, which are designed to meet the future needs.La mayor dependencia de la electricidad de la sociedad moderna hace que la fiabilidad de los sistemas de transmisión de energía sea un punto clave. Este objetivo se puede lograr mediante la supervisión continua de los parámetros de la red eléctrica, por lo que los posibles modos de fallo se pueden predecir de antemano. Se puede hacer utilizando las tecnologías existentes de Tecnologías de la Información y la Comunicación (1CT) e Internet de las cosas (lo T) que incluyen sistemas de instrumentación y comunicación inalámbrica, formando así una red de sensores inalámbricos (WSN). Los conectores eléctricos se encuentran entre las partes más críticas de cualquier sistema eléctrico y, por lo tanto, pueden actuar como nodos de dicho VVSN. Por lo tanto, el objetivo fundamental de esta tesis es el diseño, desarrollo y validación experimental de una solución IOT autoalimentada para la supervisión en tiempo real del estado de salud de un conector de subestación de alta tensión y componentes relacionados de la subestación eléctrica. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia del contacto eléctrico (ECR) del conector. Esta nueva familia de conectores de alimentación se llama SmartConnector e incorpora un sistema de recolección de energía térmica que alimenta un microcontrolador que controla un transmisor y varios sensores electrónicos para medir la temperatura, la corriente y la resistencia al contacto eléctrico (ECR) del conector. De esta manera, después del procesamiento de datos adecuado, el estado de salud del conector puede estar disponible en tiempo real, permitiendo diferentes funciones atractivas, como evaluar la correcta instalación del conector, el estado de salud actual o su vida útil restante (RUL) en tiempo real. El mismo principio también se puede utilizar para otros componentes de la subestación como espaciadores, aislantes, conductores, etc. Por lo tanto, para demostrar la universalidad de este enfoque novedoso, se aplica una estrategia similar a un espaciador, que es capaz de medir la distribución de corriente desigual en tres conductores estrechamente situados. Hay que tener cuidado de que este desarrollo técnico y científico tenga que sea compatible con las barras y "busbars" de subestación existentes, y sobre todo para ser compatible con las altas tensiones de funcionamiento, es decir, de decenas a cientos de kilovoltios (kV), y con corrientes en el orden de algunos kilo-Amperes (kA). Aunque algunas empresas eléctricas y fabricantes han progresado en el desarrollo de este tipo de tecnologías, incluidos medidores inteligentes y sensores inteligentes, los fabricantes de dispositivos eléctricos, como los fabricantes de conectores de subestación, aún no han emprendido el avance tecnológico necesario para el desarrollo de una nueva familia de componentes intel