UWB Signal Generation and Modulation Based on Photonic Approaches

Demands for efficient and reliable wireless communications between computers, mobile phones, and other portable electronic devices in short distances are increasing very fast. Ultra-wideband impulse radio is one of the promising techniques, which has gained much research interests in recent years. It covers a wide scope of applications in short-reach wireless communications. Conventionally, the low-bandwidth electronics can process the UWB signals very well. More recently, microwave photonics has enabled a new paradigm for developing UWB techniques in photonic domain. The photonic approaches offer much higher bandwidth and seamless compatibility with optical fiber networks, which allow for scaling the UWB technology to more advanced application scenarios. This chapter is included because photonic approaches have become a unique and effective technique in microwave signal processing. We do not attempt to offer a comprehensive review of UWB photonics, but rather to introduce the typical photonic solutions for UWB signal generation, modulation, transmission, down conversion, and so on

The Trade-off between Processing Gains of an Impulse Radio UWB System in the Presence of Timing Jitter

In time hopping impulse radio, $N_f$ pulses of duration $T_c$ are transmitted for each information symbol. This gives rise to two types of processing gain: (i) pulse combining gain, which is a factor $N_f$, and (ii) pulse spreading gain, which is $N_c=T_f/T_c$, where $T_f$ is the mean interval between two subsequent pulses. This paper investigates the trade-off between these two types of processing gain in the presence of timing jitter. First, an additive white Gaussian noise (AWGN) channel is considered and approximate closed form expressions for bit error probability are derived for impulse radio systems with and without pulse-based polarity randomization. Both symbol-synchronous and chip-synchronous scenarios are considered. The effects of multiple-access interference and timing jitter on the selection of optimal system parameters are explained through theoretical analysis. Finally, a multipath scenario is considered and the trade-off between processing gains of a synchronous impulse radio system with pulse-based polarity randomization is analyzed. The effects of the timing jitter, multiple-access interference and inter-frame interference are investigated. Simulation studies support the theoretical results.Comment: To appear in the IEEE Transactions on Communication

Ultra Wideband Impulse Radio Systems with Multiple Pulse Types

In an ultra wideband (UWB) impulse radio (IR) system, a number of pulses, each transmitted in an interval called a "frame", is employed to represent one information symbol. Conventionally, a single type of UWB pulse is used in all frames of all users. In this paper, IR systems with multiple types of UWB pulses are considered, where different types of pulses can be used in different frames by different users. Both stored-reference (SR) and transmitted-reference (TR) systems are considered. First, the spectral properties of a multi-pulse IR system with polarity randomization is investigated. It is shown that the average power spectral density is the average of the spectral contents of different pulse shapes. Then, approximate closed-form expressions for the bit error probability of a multi-pulse SR-IR system are derived for RAKE receivers in asynchronous multiuser environments. The effects of both inter-frame interference (IFI) and multiple-access interference (MAI) are analyzed. The theoretical and simulation results indicate that SR-IR systems that are more robust against IFI and MAI than a "conventional" SR-IR system can be designed with multiple types of ultra-wideband pulses. Finally, extensions to multi-pulse TR-IR systems are briefly described.Comment: To appear in the IEEE Journal on Selected Areas in Communications - Special Issue on Ultrawideband Wireless Communications: Theory and Application

Novel wireless modulation technique based on noise

In this paper, a new RF modulation technique is presented. Instead of using sinusoidal carriers as information bearer, pure noise is applied. This allows very simple radio architectures to be used. Spread-spectrum based technology is applied to modulate the noise bearer. Since the transmission bandwidth of the noise bearer can be made very wide, up to ultra-wideband regions, extremely large processing gains can be obtained. This will provide robustness in interference-prone environments. To avoid the local regeneration of the noise reference at the receiver, the Transmit-Reference (TR) concept is applied. In this concept, both the reference noise signal and the modulated noise signal are transmitted, together forming\ud the bearer. The reference and modulated signals are separated by applying a time offset. By applying different delay times for different channels (users) a new multiple access scheme results based on delay: Delay Division Multiple Access (DDMA). A theoretical analysis is given for the link performance of a single-user and a multi-user system. A testbed has been built to demonstrate the concept. The demonstrator operates in a 50 MHz bandwidth centered at 2.4 GHz. Processing gains ranging from 10¿30 dB have been tested. The testbed confirms the basic behavior as predicted by the theory

ATM-based TH-SSMA network for multimedia PCS

Personal communications services (PCS) promise to provide a variety of information exchanges among users with any type of mobility, at any time, in any place, through any available device. To achieve this ambitious goal, two of the major challenges in the system design are: i) to provide a high-speed wireless subsystem with large capacity and acceptable quality-of-service (QoS) and ii) to design a network architecture capable of supporting multimedia traffic and various kinds of user mobility. A time-hopping spread-spectrum wireless communication system called ultra-wide bandwidth (UWB) radio is used to provide communications that are low power, high data rate, fade resistant, and relatively shadow free in a dense multipath environment. Receiver-signal processing of UWB radio is described, and performance of such communications systems, in terms of multiple-access capability, is estimated under ideal multiple-access channel conditions. A UWB-signal propagation experiment is performed using the bandwidth in excess of 1 GHz in a typical modern office building in order to characterize the UWB-signal propagation channel. The experimental results demonstrate the feasibility of the UWB radio and its robustness in a dense multipath environment. In this paper, an ATM network is used as the backbone network due to its high bandwidth, fast switching capability, flexibility, and well-developed infrastructure. To minimize the impact caused by user mobility on the system performance, a hierarchical network-control architecture is postulated. A wireless virtual circuit (WVC) concept is proposed to improve the transmission efficiency and simplify the network control in the wireless subsystem. The key advantage of this network architecture and WVC concept is that the handoff can be done locally most of the time, due to the localized behavior of PCS users.published_or_final_versio

A low-cost time-hopping impulse radio system for high data rate transmission

We present an efficient, low-cost implementation of time-hopping impulse radio that fulfills the spectral mask mandated by the FCC and is suitable for high-data-rate, short-range communications. Key features are: (i) all-baseband implementation that obviates the need for passband components, (ii) symbol-rate (not chip rate) sampling, A/D conversion, and digital signal processing, (iii) fast acquisition due to novel search algorithms, (iv) spectral shaping that can be adapted to accommodate different spectrum regulations and interference environments. Computer simulations show that this system can provide 110Mbit/s at 7-10m distance, as well as higher data rates at shorter distances under FCC emissions limits. Due to the spreading concept of time-hopping impulse radio, the system can sustain multiple simultaneous users, and can suppress narrowband interference effectively.Comment: To appear in EURASIP Journal on Applied Signal Processing (Special Issue on UWB - State of the Art

Multi Detector Fusion of Dynamic TOA Estimation using Kalman Filter

In this paper, we propose fusion of dynamic TOA (time of arrival) from multiple non-coherent detectors like energy detectors operating at sub-Nyquist rate through Kalman filtering. We also show that by using multiple of these energy detectors, we can achieve the performance of a digital matched filter implementation in the AWGN (additive white Gaussian noise) setting. We derive analytical expression for number of energy detectors needed to achieve the matched filter performance. We demonstrate in simulation the validity of our analytical approach. Results indicate that number of energy detectors needed will be high at low SNRs and converge to a constant number as the SNR increases. We also study the performance of the strategy proposed using IEEE 802.15.4a CM1 channel model and show in simulation that two sub-Nyquist detectors are sufficient to match the performance of digital matched filter