Experimental Evaluation and Comparison of Time-Multiplexed Multi-FPGA Routing Architectures

Emulating large complex designs require multi-FPGA systems (MFS). However, inter-FPGA communication is confronted by the challenge of lack of interconnect capacity due to limited number of FPGA input/output (I/O) pins. Serializing parallel signals onto a single trace effectively addresses the limited I/O pin obstacle. Besides the multiplexing scheme and multiplexing ratio (number of inter-FPGA signals per trace), the choice of the MFS routing architecture also affect the critical path latency. The routing architecture of an MFS is the interconnection pattern of FPGAs, fixed wires and/or programmable interconnect chips. Performance of existing MFS routing architectures is also limited by off-chip interface selection. In this dissertation we proposed novel 2D and 3D latency-optimized time-multiplexed MFS routing architectures. We used rigorous experimental approach and real sequential benchmark circuits to evaluate and compare the proposed and existing MFS routing architectures. This research provides a new insight into the encouraging effects of using off-chip optical interface and three dimensional MFS routing architectures. The vertical stacking results in shorter off-chip links improving the overall system frequency with the additional advantage of smaller footprint area. The proposed 3D architectures employed serialized interconnect between intra-plane and inter-plane FPGAs to address the pin limitation problem. Additionally, all off-chip links are replaced by optical fibers that exhibited latency improvement and resulted in faster MFS. Results indicated that exploiting third dimension provided latency and area improvements as compared to 2D MFS. We also proposed latency-optimized planar 2D MFS architectures in which electrical interconnections are replaced by optical interface in same spatial distribution. Performance evaluation and comparison showed that the proposed architectures have reduced critical path delay and system frequency improvement as compared to conventional MFS. We also experimentally evaluated and compared the system performance of three inter-FPGA communication schemes i.e. Logic Multiplexing, SERDES and MGT in conjunction with two routing architectures i.e. Completely Connected Graph (CCG) and TORUS. Experimental results showed that SERDES attained maximum frequency than the other two schemes. However, for very high multiplexing ratios, the performance of SERDES & MGT became comparable

Real-Time Waveform Prototyping

Mobile Netzwerke der fünften Generation zeichen sich aus durch vielfältigen Anforderungen und Einsatzszenarien. Drei unterschiedliche Anwendungsfälle sind hierbei besonders relevant: 1) Industrie-Applikationen fordern Echtzeitfunkübertragungen mit besonders niedrigen Ausfallraten. 2) Internet-of-things-Anwendungen erfordern die Anbindung einer Vielzahl von verteilten Sensoren. 3) Die Datenraten für Anwendung wie z.B. der Übermittlung von Videoinhalten sind massiv gestiegen. Diese zum Teil gegensätzlichen Erwartungen veranlassen Forscher und Ingenieure dazu, neue Konzepte und Technologien für zukünftige drahtlose Kommunikationssysteme in Betracht zu ziehen. Ziel ist es, aus einer Vielzahl neuer Ideen vielversprechende Kandidatentechnologien zu identifizieren und zu entscheiden, welche für die Umsetzung in zukünftige Produkte geeignet sind. Die Herausforderungen, diese Anforderungen zu erreichen, liegen jedoch jenseits der Möglichkeiten, die eine einzelne Verarbeitungsschicht in einem drahtlosen Netzwerk bieten kann. Daher müssen mehrere Forschungsbereiche Forschungsideen gemeinsam nutzen. Diese Arbeit beschreibt daher eine Plattform als Basis für zukünftige experimentelle Erforschung von drahtlosen Netzwerken unter reellen Bedingungen. Es werden folgende drei Aspekte näher vorgestellt: Zunächst erfolgt ein Überblick über moderne Prototypen und Testbed-Lösungen, die auf großes Interesse, Nachfrage, aber auch Förderungsmöglichkeiten stoßen. Allerdings ist der Entwicklungsaufwand nicht unerheblich und richtet sich stark nach den gewählten Eigenschaften der Plattform. Der Auswahlprozess ist jedoch aufgrund der Menge der verfügbaren Optionen und ihrer jeweiligen (versteckten) Implikationen komplex. Daher wird ein Leitfaden anhand verschiedener Beispiele vorgestellt, mit dem Ziel Erwartungen im Vergleich zu den für den Prototyp erforderlichen Aufwänden zu bewerten. Zweitens wird ein flexibler, aber echtzeitfähiger Signalprozessor eingeführt, der auf einer software-programmierbaren Funkplattform läuft. Der Prozessor ermöglicht die Rekonfiguration wichtiger Parameter der physikalischen Schicht während der Laufzeit, um eine Vielzahl moderner Wellenformen zu erzeugen. Es werden vier Parametereinstellungen 'LLC', 'WiFi', 'eMBB' und 'IoT' vorgestellt, um die Anforderungen der verschiedenen drahtlosen Anwendungen widerzuspiegeln. Diese werden dann zur Evaluierung der die in dieser Arbeit vorgestellte Implementierung herangezogen. Drittens wird durch die Einführung einer generischen Testinfrastruktur die Einbeziehung externer Partner aus der Ferne ermöglicht. Das Testfeld kann hier für verschiedenste Experimente flexibel auf die Anforderungen drahtloser Technologien zugeschnitten werden. Mit Hilfe der Testinfrastruktur wird die Leistung des vorgestellten Transceivers hinsichtlich Latenz, erreichbarem Durchsatz und Paketfehlerraten bewertet. Die öffentliche Demonstration eines taktilen Internet-Prototypen, unter Verwendung von Roboterarmen in einer Mehrbenutzerumgebung, konnte erfolgreich durchgeführt und bei mehreren Gelegenheiten präsentiert werden.:List of figures List of tables Abbreviations Notations 1 Introduction 1.1 Wireless applications 1.2 Motivation 1.3 Software-Defined Radio 1.4 State of the art 1.5 Testbed 1.6 Summary 2 Background 2.1 System Model 2.2 PHY Layer Structure 2.3 Generalized Frequency Division Multiplexing 2.4 Wireless Standards 2.4.1 IEEE 802.15.4 2.4.2 802.11 WLAN 2.4.3 LTE 2.4.4 Low Latency Industrial Wireless Communications 2.4.5 Summary 3 Wireless Prototyping 3.1 Testbed Examples 3.1.1 PHY - focused Testbeds 3.1.2 MAC - focused Testbeds 3.1.3 Network - focused testbeds 3.1.4 Generic testbeds 3.2 Considerations 3.3 Use cases and Scenarios 3.4 Requirements 3.5 Methodology 3.6 Hardware Platform 3.6.1 Host 3.6.2 FPGA 3.6.3 Hybrid 3.6.4 ASIC 3.7 Software Platform 3.7.1 Testbed Management Frameworks 3.7.2 Development Frameworks 3.7.3 Software Implementations 3.8 Deployment 3.9 Discussion 3.10 Conclusion 4 Flexible Transceiver 4.1 Signal Processing Modules 4.1.1 MAC interface 4.1.2 Encoding and Mapping 4.1.3 Modem 4.1.4 Post modem processing 4.1.5 Synchronization 4.1.6 Channel Estimation and Equalization 4.1.7 Demapping 4.1.8 Flexible Configuration 4.2 Analysis 4.2.1 Numerical Precision 4.2.2 Spectral analysis 4.2.3 Latency 4.2.4 Resource Consumption 4.3 Discussion 4.3.1 Extension to MIMO 4.4 Summary 5 Testbed 5.1 Infrastructure 5.2 Automation 5.3 Software Defined Radio Platform 5.4 Radio Frequency Front-end 5.4.1 Sub 6 GHz front-end 5.4.2 26 GHz mmWave front-end 5.5 Performance evaluation 5.6 Summary 6 Experiments 6.1 Single Link 6.1.1 Infrastructure 6.1.2 Single Link Experiments 6.1.3 End-to-End 6.2 Multi-User 6.3 26 GHz mmWave experimentation 6.4 Summary 7 Key lessons 7.1 Limitations Experienced During Development 7.2 Prototyping Future 7.3 Open points 7.4 Workflow 7.5 Summary 8 Conclusions 8.1 Future Work 8.1.1 Prototyping Workflow 8.1.2 Flexible Transceiver Core 8.1.3 Experimental Data-sets 8.1.4 Evolved Access Point Prototype For Industrial Networks 8.1.5 Testbed Standardization A Additional Resources A.1 Fourier Transform Blocks A.2 Resource Consumption A.3 Channel Sounding using Chirp sequences A.3.1 SNR Estimation A.3.2 Channel Estimation A.4 Hardware part listThe demand to achieve higher data rates for the Enhanced Mobile Broadband scenario and novel fifth generation use cases like Ultra-Reliable Low-Latency and Massive Machine-type Communications drive researchers and engineers to consider new concepts and technologies for future wireless communication systems. The goal is to identify promising candidate technologies among a vast number of new ideas and to decide, which are suitable for implementation in future products. However, the challenges to achieve those demands are beyond the capabilities a single processing layer in a wireless network can offer. Therefore, several research domains have to collaboratively exploit research ideas. This thesis presents a platform to provide a base for future applied research on wireless networks. Firstly, by giving an overview of state-of-the-art prototypes and testbed solutions. Secondly by introducing a flexible, yet real-time physical layer signal processor running on a software defined radio platform. The processor enables reconfiguring important parameters of the physical layer during run-time in order to create a multitude of modern waveforms. Thirdly, by introducing a generic test infrastructure, which can be tailored to prototype diverse wireless technology and which is remotely accessible in order to invite new ideas by third parties. Using the test infrastructure, the performance of the flexible transceiver is evaluated regarding latency, achievable throughput and packet error rates.:List of figures List of tables Abbreviations Notations 1 Introduction 1.1 Wireless applications 1.2 Motivation 1.3 Software-Defined Radio 1.4 State of the art 1.5 Testbed 1.6 Summary 2 Background 2.1 System Model 2.2 PHY Layer Structure 2.3 Generalized Frequency Division Multiplexing 2.4 Wireless Standards 2.4.1 IEEE 802.15.4 2.4.2 802.11 WLAN 2.4.3 LTE 2.4.4 Low Latency Industrial Wireless Communications 2.4.5 Summary 3 Wireless Prototyping 3.1 Testbed Examples 3.1.1 PHY - focused Testbeds 3.1.2 MAC - focused Testbeds 3.1.3 Network - focused testbeds 3.1.4 Generic testbeds 3.2 Considerations 3.3 Use cases and Scenarios 3.4 Requirements 3.5 Methodology 3.6 Hardware Platform 3.6.1 Host 3.6.2 FPGA 3.6.3 Hybrid 3.6.4 ASIC 3.7 Software Platform 3.7.1 Testbed Management Frameworks 3.7.2 Development Frameworks 3.7.3 Software Implementations 3.8 Deployment 3.9 Discussion 3.10 Conclusion 4 Flexible Transceiver 4.1 Signal Processing Modules 4.1.1 MAC interface 4.1.2 Encoding and Mapping 4.1.3 Modem 4.1.4 Post modem processing 4.1.5 Synchronization 4.1.6 Channel Estimation and Equalization 4.1.7 Demapping 4.1.8 Flexible Configuration 4.2 Analysis 4.2.1 Numerical Precision 4.2.2 Spectral analysis 4.2.3 Latency 4.2.4 Resource Consumption 4.3 Discussion 4.3.1 Extension to MIMO 4.4 Summary 5 Testbed 5.1 Infrastructure 5.2 Automation 5.3 Software Defined Radio Platform 5.4 Radio Frequency Front-end 5.4.1 Sub 6 GHz front-end 5.4.2 26 GHz mmWave front-end 5.5 Performance evaluation 5.6 Summary 6 Experiments 6.1 Single Link 6.1.1 Infrastructure 6.1.2 Single Link Experiments 6.1.3 End-to-End 6.2 Multi-User 6.3 26 GHz mmWave experimentation 6.4 Summary 7 Key lessons 7.1 Limitations Experienced During Development 7.2 Prototyping Future 7.3 Open points 7.4 Workflow 7.5 Summary 8 Conclusions 8.1 Future Work 8.1.1 Prototyping Workflow 8.1.2 Flexible Transceiver Core 8.1.3 Experimental Data-sets 8.1.4 Evolved Access Point Prototype For Industrial Networks 8.1.5 Testbed Standardization A Additional Resources A.1 Fourier Transform Blocks A.2 Resource Consumption A.3 Channel Sounding using Chirp sequences A.3.1 SNR Estimation A.3.2 Channel Estimation A.4 Hardware part lis

大規模システムLSI設計のための統一的ハードウェア・ソフトウェア協調検証手法

Currently, the complexity of embedded LSI system is growing faster than the productivity of system design. This trend results in a design productivity gap, particularly in tight development time. Since the verification task takes bigger part of development task, it becomes a major challenge in LSI system design. In order to guarantee system reliability and quality of results (QoR), verifying large coverage of system functionality requires huge amount of relevant test cases and various scenario of evaluations. To overcome these problems, verification methodology is evolving toward supporting higher level of design abstraction by employing HW-SW co-verification. In this study, we present a novel approach for verification LSI circuit which is called as unified HW/SW co-verification framework. The study aims to improve design efficiency while maintains implementation consistency in the point of view of system-level performance. The proposed data-driven simulation and flexible interface of HW and SW design become the backbone of verification framework. In order to avoid time consuming, prone error, and iterative design spin-off in a large team, the proposed framework has to support multiple design abstractions. Hence, it can close the loop of design, exploration, optimization, and testing. Furthermore, the proposed methodology is also able to co-operate with system-level simulation in high-level abstraction, which is easy to extend for various applications and enables fast-turn around design modification. These contributions are discussed in chapter 3. In order to show the effectiveness and the use-cases of the proposed verification framework, the evaluation and metrics assessments of Very High Throughput wireless LAN system design are carried out. Two application examples are provided. The first case in chapter 4 is intended for fast verification and design exploration of large circuit. The Maximum Likelihood Detection (MLD) MIMO decoder is considered as Design Under Test (DUT). The second case, as presented in chapter 5, is the evaluation for system-level simulation. The full transceiver system based on IEEE 802.11ac standard is employed as DUT. Experimental results show that the proposed verification approach gives significant improvements of verification time (e.g. up to 10,000 times) over the conventional scheme. The proposed framework is also able to support various schemes of system level evaluations and cross-layer evaluation of wireless system.九州工業大学博士学位論文 学位記番号：情工博甲第328号 学位授与年月日：平成29年6月30日1 Introduction|2 Design and Verification in LSI System Design|3 Unified HW/SW Co-verification Methodology|4 Fast Co-verification and Design Exploration in Complex Circuits|5 Unified System Level Simulator for Very High Throughput Wireless Systems|6 Conclusion and Future Work九州工業大学平成29年

Uso de técnicas de combinação de diversidade e fatores de espalhamento estendidos para melhorar a performance e reduzir a complexidade do receptor OFDM em IEEE 802.15.4g

Orientadores: Renato da Rocha Lopes, Eduardo Rodrigues de LimaDissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de ComputaçãoResumo: EEE 802.15.4g é um adendo da norma IEEE 802.15.4 focada em Smart Utility Network (SUN), e dedicada a requisitos de comunicação no contexto de Low Rate (LR) Wireless Personal Area Network (WPAN). Hoje em dia, devido às suas características, o adendo foca em apliações de Smart Ubiquitous Network, como cidades inteligentes e Internet das Coisas (IoT). Uma das três Camadas Físicas (PHYs) definidas na norma é a Multi-Rate and Multi-Regional Orthogonal Frequency Division Multiplexing (MR-OFDM). Além de outras características, o MR-OFDM emprega o método Frequency Spreading (FS) para reduzir a Peak-to-Average Power Ratio (PAPR) do símbolo OFDM. Sob algumas premissas do canal, este trabalho mostra que o FS também pode introduzir diversidade em frequência à camada física. Este trabalho propõe um método para reverter o espalhamento de frequência que explora diversidade em IEEE 802.15.4g MR-OFDM. O método segue duas abordagens: o uso de técnicas de combinação de diversidade e a proposta de novas configurações de Modulation and Coding Scheme (MCS) usando fatores de espalhamento estendidos. Em um canal com distribuição Rayleigh e assumindo subportadoras não correlacionadas, o método proposto mostra melhorias de até 10.35 dB quando comparado ao MR-OFDM, revertendo o espa-lhamento de frequência de forma direta, usando configurações originais. O método é válido mesmo na presença de erros na estimativa do canal e bandas de coerência largas. O trabalho faz parte de um projeto maior que visa a implementação de um circuito integrado capaz de suportar as três camadas físicas definias em IEEE 802.15.4g, não apenas o MR-OFDM. Devido a isso, o método deve ser totalmente compatível com a norma e focar na complexidade de implementação do receptor MR-OFDMAbstract: IEEE 802.15.4g is an amendment of the IEEE 802.15.4 standard focused on Smart Utility Networks (SUN), and devoted to the communication requirements of Low Rate Wireless Personal Area Network (LR-WPAN). Nowadays, due to its characteristics, the amendment focuses on Smart Ubiquitous Network applications, such as Smart City and Internet of Things (IoT). One of the three Physical Layers (PHYs) defined in the standard is the Multi-Rate and Multi-Regional Orthogonal Frequency Division Multiplexing (MR-OFDM). In addition to other features, the MR-OFDM employs frequency spreading to reduce the Peak-to-Average Power Ratio (PAPR) of the OFDM symbol. Under some channel assumptions, this frequency spreading can also introduce frequency diversity to the PHY. This work proposes a method to perform frequency despreading that exploits diversity in the IEEE 802.15.4g MR-OFDM PHY. The method follows two approaches: the use of diversity combining techniques and the proposal of new Modulation and Coding Scheme (MCS) configurations using extended spreading factors. In a channel with Rayleigh distribution and assuming uncorrelated subcarriers, the proposed method shows improvements up to 10.35 dB when compared to the MR-OFDM performing frequency despreading using original configurations. The method is valid even in the presence of channel estimation errors and large channel coherence bandwidths. The work is part of a larger project which aims at the implementation of an Integrated Circuit capable of handling the three PHYs defined in the IEEE802.15.4g, not only the MR-OFDM. Thus, the method must be fully compliant to the standard and focus on the MR-OFDM receiver implementation complexityMestradoTelecomunicações e TelemáticaMestre em Engenharia Elétric

A MIMO-OFDM testbed, channel measurements, and system considerations for outdoor-indoor WiMAX

The design, implementation, and test of a real-time flexible 2×2 (Multiple Input Multiple Output-Orthogonal Frequency Division Multiplexing) MIMO-OFDM IEEE 802.16 prototype are presented. For the design, a channel measurement campaign on the 3.5GHz band has been carried out, focusing on outdoor-indoor scenarios. The analysis of measured channels showed that higher capacity can be achieved in case of obstructed scenarios and that (Channel Distribution Information at the Transmitter) CDIT capacity is close to (Channel State Information at the Transmitter) CSIT with much lower complexity and requirements in terms of channel estimation and feedback. The baseband prototype used an (Field Programmable Gate Array) FPGA where enhanced signal processing algorithms are implemented in order to improve system performance. We have shown that for MIMO-OFDM systems, extra signal processing such as enhanced joint channel and frequency offset estimation is needed to obtain a good performance and approach in practice the theoretical capacity improvements

Design methodology addressing static/reconfigurable partitioning optimizing software defined radio (SDR) implementation through FPGA dynamic partial reconfiguration and rapid prototyping tools

The characteristics people request for communication devices become more and more demanding every day. And not only in those aspects dealing with communication speed, but also in such different characteristics as different communication standards compatibility, battery life, device size or price. Moreover, when this communication need is addressed by the industrial world, new characteristics such as reliability, robustness or time-to-market appear. In this context, Software Defined Radios (SDR) and evolutions such as Cognitive Radios or Intelligent Radios seem to be the technological answer that will satisfy all these requirements in a short and mid-term. Consequently, this PhD dissertation deals with the implementation of this type of communication system. Taking into account that there is no limitation neither in the implementation architecture nor in the target device, a novel framework for SDR implementation is proposed. This framework is made up of FPGAs, using dynamic partial reconfiguration, as target device and rapid prototyping tools as designing tool. Despite the benefits that this framework generates, there are also certain drawbacks that need to be analyzed and minimized to the extent possible. On this purpose, a SDR design methodology has been designed and tested. This methodology addresses the static/reconfigurable partitioning of the SDRs in order to optimize their implementation in the aforementioned framework. In order to verify the feasibility of both the design framework and the design methodology, several implementations have been carried out making use of them. A multi-standard modulator implementing WiFi, WiMAX and UMTS, a small-form-factor cognitive video transmission system and the implementation of several data coding functions over R3TOS, a hardware operating system developed by the University of Edinburgh, are these implementations.Las características que la gente exige a los dispositivos de comunicaciones son cada día más exigentes. Y no solo en los aspectos relacionados con la velocidad de comunicación, sino que también en diferentes características como la compatibilidad con diferentes estándares de comunicación, autonomía, tamaño o precio. Es más, cuando esta necesidad de comunicación se traslada al mundo industrial, aparecen nuevas características como fiabilidad, robustez o plazo de comercialización que también es necesario cubrir. En este contexto, las Radios Definidas por Software (SDR) y evoluciones como las Radios Cognitivas o Radios Inteligentes parecen la respuesta tecnológica que va a satisfacer estas necesidades a corto y medio plazo. Por ello, esta tesis doctoral aborda la implementación de este tipo de sistemas de comunicaciones. Teniendo en cuenta que no existe una limitación, ni en la arquitectura de implementación, ni en el tipo de dispositivo a usar, se propone un nuevo entrono de diseño formado por las FPGAs, haciendo uso de la reconfiguración parcial dinámica, y por las herramientas de prototipado rápido. A pesar de que este entorno de diseño ofrece varios beneficios, también genera algunos inconvenientes que es necesario analizar y minimizar en la medida de lo posible. Con este objetivo, se ha diseñado y verificado una metodología de diseño de SDRs. Esta metodología se encarga del particionado estático/reconfigurable de las SDRs para optimizar su implementación sobre el entrono de diseño antes comentado. Para verificar la viabilidad tanto del entorno, como de la metodología de diseño propuesta, se han realizado varias implementaciones que hacen uso de ambas cosas. Estas implementaciones son: un modulador multi-estándar que implementa WiFi, WiMAX y UMTS, un sistema cognitivo y compacto de transmisión de video y la implementación de varias funciones de codificación de datos sobre R3TOS, un sistema operativo hardware desarrollado por la Universidad de Edimburgo

Architectures for Cognitive Radio Testbeds and Demonstrators – An Overview

Wireless communication standards are developed at an ever-increasing rate of pace, and significant amounts of effort is put into research for new communication methods and concepts. On the physical layer, such topics include MIMO, cooperative communication, and error control coding, whereas research on the medium access layer includes link control, network topology, and cognitive radio. At the same time, implementations are moving from traditional fixed hardware architectures towards software, allowing more efficient development. Today, field-programmable gate arrays (FPGAs) and regular desktop computers are fast enough to handle complete baseband processing chains, and there are several platforms, both open-source and commercial, providing such solutions. The aims of this paper is to give an overview of five of the available platforms and their characteristics, and compare the features and performance measures of the different systems