Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology

Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs

This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account. In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected. The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration

A 12b 50MS/s 2.1mW SAR ADC with redundancy and digital background calibration

A 12-bit 50MS/s SAR ADC implemented in 65nm CMOS technology is presented. The design employs redundancy to relax the DAC settling requirement and to provide sufficient room for errors such that the static nonlinearity caused by capacitor mismatches can be digitally removed. The redundancy is incorporated into the design using a tri-level switching scheme and our modified split-capacitor array to achieve the highest switching efficiency while still preserving the symmetry in error tolerance. A new code-density based digital background calibration algorithm that requires no special calibration signals or additional analog hardware is also developed. The calibration is performed by using the input signal as stimulus and the effectiveness is verified both in simulation and through measured data. The prototype achieves a 67.4dB SNDR at 50MS/s, while dissipating 2.1mW from a 1.2V supply, leading to FoM of 21.9fJ/conv.-step at Nyquist frequency.MIT Masdar Progra

DIGITALLY ASSISTED TECHNIQUES FOR NYQUIST RATE ANALOG-to-DIGITAL CONVERTERS

With the advance of technology and rapid growth of digital systems, low power high speed analog-to-digital converters with great accuracy are in demand. To achieve high effective number of bits Analog-to-Digital Converter(ADC) calibration as a time consuming process is a potential bottleneck for designs. This dissertation presentsa fully digital background calibration algorithm for a 7-bit redundant flash ADC using split structure and look-up table based correction. Redundant comparators are used in the flash ADC design of this work in order to tolerate large offset voltages while minimizing signal input capacitance. The split ADC structure helps by eliminating the unknown input signal from the calibration path. The flash ADC has been designed in 180nm IBM CMOS technology and fabricated through MOSIS. This work was supported by Analog Devices, Wilmington,MA. While much research on ADC design has concentrated on increasing resolution and sample rate, there are many applications (e.g. biomedical devices and sensor networks) that do not require high performance but do require low power energy efficient ADCs. This dissertation also explores on design of a low quiescent current 100kSps Successive Approximation (SAR) ADC that has been used as an error detection ADC for an automotive application in 350nm CD (CMOS-DMOS) technology. This work was supported by ON Semiconductor Corp, East Greenwich,RI

Design and implementation of Radix-3/Radix-2 based novel hybrid SAR ADC in scaled CMOS technologies

This thesis focuses on low power and high speed design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nanoscale CMOS technologies. SAR ADCs’ speed is limited by the number of bits of resolution. An N-bit conventional SAR ADC takes N conversion cycles. To speed up the conversion process, we introduce a radix-3 SAR ADC which can compute 1:6 bits per cycle. To our knowledge, it is the first fully programmable and efficiently hardware controlled radix-3 SAR ADC. We had to use two comparators per cycle due to ADC architecture and we proposed a simple calibration scheme for the comparators. Also, as the architecture of the DAC array is completely different from the architecture of conventional radix-2 SAR ADC’s DAC arrays, we came up with an algorithm for calibration of capacitors of the DAC. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. Due to our proposed architecture,the radix-3 SAR ADC uses two comparators per cycle and two differential DACs. To improve the comparator’s power efficiency, an efficient and low cost calibration technique has been introduced. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR). To improve the DAC switching energy, we introduced a radix-3/radix-2 based novel hybrid SAR ADC. We use two single ended DACs for radix-3 SAR ADC and these two single ended DACs can be used as one differential DAC for radix-2 SAR ADC. So, overall, we only have a single DAC as conventional radix- 2 SAR ADC. In addition, a monotonic switching technique is adopted for radix-2 search to reduce the DAC capacitor size and hence, to reduce switching power. It can reduce the total number of unit capacitors by four times. Our proposed hybrid SAR ADC can achieve less DAC energy compared to radix-3 and radix-2 SAR ADCs. Also, to utilize technology scaling, we used the minimum capacitor size allowed by thermal noise limitations. To achieve high resolution, we introduced calibration algorithm for the DAC array. As mentioned earlier, the radix-3 SAR ADC offers higher power than conventional radix-2 SAR ADC because of simultaneous use of two comparators. In the proposed hybrid SAR ADC, we will be using radix-3 search for first few MSB bits. So, the resolution required for radix-3 comparators are much larger than the LSB value of 10-bit ADC. By implementing calibration of comparators, we can use low power, high input referred offset and high speed comparators for radix-3 search. Radix-2 search will be used for rest of the bits and the resolution of the radix-2 comparator has to be less than the required LSB value. So, a high power, low input referred offset and high speed comparator is used for radix-2 search. Also, we introduced clock gating for comparators. So, radix-3 comparators will not toggle during radix-2 search and the radix-2 comparators will be inactive during radix-3 search. By using the aforementioned techniques, the overall comparator power is definitely less than a radix-3 SAR ADC and comparable to a conventional radix-2 SAR ADC. A prototype radix-3/radix-2 based hybrid SAR ADC with the proposed technique is designed and fabricated in 40nm CMOS technology. It achieves an SNDR of 56.9 dB and consumes only 0.38 mW power at 30MS/s, leading to a Walden figure of merit of 21.5 fJ/conv-step.Electrical and Computer Engineerin

Built-in-self-test and foreground calibration of SAR ADCs

This thesis explores the scope of ‘Built-in-Self-Test’(BIST) schemes to reduce the time cost complexity associated with the production tests for static linearity errors in Successive Approximation (SAR) ADCs. In this regard, an on-chip implementation of the ‘Stimulus Based Error Identification and Removal’ (SEIR) method [1] is sought to be pursued. As an extension, it is proposed that the estimated ADC non-linearities may then be suitably calibrated to achieve higher resolution. A brief review of the testing and calibration algorithm is undertaken. Further, this work elaborates on the design of a prototype front-end test generator and a buffer interface to calibrate a 10MHz 14 bit redundant SAR ADC in the TSMC 180nm process. Simulation results validating the circuit implementation of the integrated front-end system have been presented.Electrical and Computer Engineerin

Background Calibration of a 6-Bit 1Gsps Split-Flash ADC

In this MS thesis, a redundant flash analog-to-digital converter (ADC) using a ``Split-ADC\u27 calibration structure and lookup-table-based correction is presented. ADC input capacitance is minimized through use of small, power efficient comparators; redundancy is used to tolerate the resulting large offset voltages. Correction of errors and estimation of calibration parameters are performed continuously in the background in the digital domain. The proposed flash ADC has an effective-number-of-bits (ENOB) of 6-bits and is designed for a target sampling rate of 1Gs/s in 180nm CMOS. The calibration algorithm described has been simulated in MATLAB and an FPGA implementation has been investigated