Low power techniques for video compression

This paper gives an overview of low-power techniques proposed in the literature for mobile multimedia and Internet applications. Exploitable aspects are discussed in the behavior of different video compression tools. These power-efficient solutions are then classified by synthesis domain and level of abstraction. As this paper is meant to be a starting point for further research in the area, a lowpower hardware & software co-design methodology is outlined in the end as a possible scenario for video-codec-on-a-chip implementations on future mobile multimedia platforms

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Dynamic reconfiguration technologies based on FPGA in software defined radio system

Partial Reconfiguration (PR) is a method for Field Programmable Gate Array (FPGA) designs which allows multiple applications to time-share a portion of an FPGA while the rest of the device continues to operate unaffected. Using this strategy, the physical layer processing architecture in Software Defined Radio (SDR) systems can benefit from reduced complexity and increased design flexibility, as different waveform applications can be grouped into one part of a single FPGA. Waveform switching often means not only changing functionality, but also changing the FPGA clock frequency. However, that is beyond the current functionality of PR processes as the clock components (such as Digital Clock Managers (DCMs)) are excluded from the process of partial reconfiguration. In this paper, we present a novel architecture that combines another reconfigurable technology, Dynamic Reconfigurable Port (DRP), with PR based on a single FPGA in order to dynamically change both functionality and also the clock frequency. The architecture is demonstrated to reduce hardware utilization significantly compared with standard, static FPGA design

Experimental study of artificial neural networks using a digital memristor simulator

© 2018 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes,creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.This paper presents a fully digital implementation of a memristor hardware simulator, as the core of an emulator, based on a behavioral model of voltage-controlled threshold-type bipolar memristors. Compared to other analog solutions, the proposed digital design is compact, easily reconfigurable, demonstrates very good matching with the mathematical model on which it is based, and complies with all the required features for memristor emulators. We validated its functionality using Altera Quartus II and ModelSim tools targeting low-cost yet powerful field programmable gate array (FPGA) families. We tested its suitability for complex memristive circuits as well as its synapse functioning in artificial neural networks (ANNs), implementing examples of associative memory and unsupervised learning of spatio-temporal correlations in parallel input streams using a simplified STDP. We provide the full circuit schematics of all our digital circuit designs and comment on the required hardware resources and their scaling trends, thus presenting a design framework for applications based on our hardware simulator.Peer ReviewedPostprint (author's final draft

Pipelining Of Double Precision Floating Point Division And Square Root Operations On Field-programmable Gate Arrays

Many space applications, such as vision-based systems, synthetic aperture radar, and radar altimetry rely increasingly on high data rate DSP algorithms. These algorithms use double precision floating point arithmetic operations. While most DSP applications can be executed on DSP processors, the DSP numerical requirements of these new space applications surpass by far the numerical capabilities of many current DSP processors. Since the tradition in DSP processing has been to use fixed point number representation, only recently have DSP processors begun to incorporate floating point arithmetic units, even though most of these units handle only single precision floating point addition/subtraction, multiplication, and occasionally division. While DSP processors are slowly evolving to meet the numerical requirements of newer space applications, FPGA densities have rapidly increased to parallel and surpass even the gate densities of many DSP processors and commodity CPUs. This makes them attractive platforms to implement compute-intensive DSP computations. Even in the presence of this clear advantage on the side of FPGAs, few attempts have been made to examine how wide precision floating point arithmetic, particularly division and square root operations, can perform on FPGAs to support these compute-intensive DSP applications. In this context, this thesis presents the sequential and pipelined designs of IEEE-754 compliant double floating point division and square root operations based on low radix digit recurrence algorithms. FPGA implementations of these algorithms have the advantage of being easily testable. In particular, the pipelined designs are synthesized based on careful partial and full unrolling of the iterations in the digit recurrence algorithms. In the overall, the implementations of the sequential and pipelined designs are common-denominator implementations which do not use any performance-enhancing embedded components such as multipliers and block memory. As these implementations exploit exclusively the fine-grain reconfigurable resources of Virtex FPGAs, they are easily portable to other FPGAs with similar reconfigurable fabrics without any major modifications. The pipelined designs of these two operations are evaluated in terms of area, throughput, and dynamic power consumption as a function of pipeline depth. Pipelining experiments reveal that the area overhead tends to remain constant regardless of the degree of pipelining to which the design is submitted, while the throughput increases with pipeline depth. In addition, these experiments reveal that pipelining reduces power considerably in shallow pipelines. Pipelining further these designs does not necessarily lead to significant power reduction. By partitioning these designs into deeper pipelines, these designs can reach throughputs close to the 100 MFLOPS mark by consuming a modest 1% to 8% of the reconfigurable fabric within a Virtex-II XC2VX000 (e.g., XC2V1000 or XC2V6000) FPGA

Utilization of advanced self-diagnostic functions implemented in frequency inverters for the purpose of the computer-aided identification of operating …

The article is a continuation of papers published in previous publications referred to the development of the Computer Control and Diagnostic System of Distributed Drives [1, 2, 3]. Authors of the paper focused on the group of frequency inverters coupled by the ProfiBus DP network, elaborated expert system and integrated control and diagnostic blocks placed in the PLC memory, at an angle of possibility of utilization of integrated selfdiagnostic algorithms of frequency inverters to the implementation in the Computer Control and Diagnosis System of Distributed Drives (CCaDSoDD) system. The article includes also an analysis of potential possibilities of utilization of embedded functions and restrictions connected with accepted assumptions

Design of Timer for Application in ATM using FPGA and VHDL

A watchdog timer is a computer hardware timing device that triggers a system reset if the main program, due to some fault condition, such as a hang, neglects to regularly service the watchdog (writing a “service pulse” to it, also referred to as “petting the dog”). The intention is to bring the system back from the hung state into normal operation. Such a timer has got various important applications, one of them being in ATMs (Automated Teller Machine) which we have studied and designed in our project