Multi-domain crankback operation for IP/MPLS & DWDM networks

Network carriers and operators have built and deployed a very wide range of networking technologies to meet their customers needs. These include ultra scalable fibre-optic backbone networks based upon dense wavelength division multiplexing (DWDM) solutions as well as advanced layer 2/3 IP multiprotocol label switching (MPLS) and Ethernet technologies as well. A range of networking control protocols has also been developed to implement service provisioning and management across these networks. As these infrastructures have been deployed, a range of new challenges have started to emerge. In particular, a major issue is that of provisioning connection services between networks running across different domain boundaries, e.g., administrative geographic, commercial, etc. As a result, many carriers are keenly interested in the design of multi-domain provisioning solutions and algorithms. Nevertheless, to date most such efforts have only looked at pre-configured, i.e., static, inter-domain route computation or more complex solutions based upon hierarchical routing. As such there is significant scope in developing more scalable and simplified multi-domain provisioning solutions. Moreover, it is here that crankback signaling offers much promise. Crankback makes use of active messaging techniques to compute routes in an iterative manner and avoid problematic resource-deficient links. However very few multi-domain crankback schemes have been proposed, leaving much room for further investigation. Along these lines, this thesis proposes crankback signaling solution for multi-domain IP/MPLS and DWDM network operation. The scheme uses a joint intra/inter-domain signaling strategy and is fully-compatible with the standardized resource reservation (RSVP-TE) protocol. Furthermore, the proposed solution also implements and advanced next-hop domain selection strategy to drive the overall crankback process. Finally the whole framework assumes realistic settings in which individual domains have full internal visibility via link-state routing protocols, e.g., open shortest path first traffic engineering (OSPF-TE), but limited \u27next-hop\u27 inter-domain visibility, e.g., as provided by inter-area or inter-autonomous system (AS) routing protocols. The performance of the proposed crankback solution is studied using software-based discrete event simulation. First, a range of multi-domain topologies are built and tested. Next, detailed simulation runs are conducted for a range of scenarios. Overall, the findings show that the proposed crankback solution is very competitive with hierarchical routing, in many cases even outperforming full mesh abstraction. Moreover the scheme maintains acceptable signaling overheads (owing to it dual inter/intra domain crankback design) and also outperforms existing multi-domain crankback algorithms.\u2

Characterization, design and re-optimization on multi-layer optical networks

L'augment de volum de tràfic IP provocat per l'increment de serveis multimèdia com HDTV o vídeo conferència planteja nous reptes als operadors de xarxa per tal de proveir transmissió de dades eficient. Tot i que les xarxes mallades amb multiplexació per divisió de longitud d'ona (DWDM) suporten connexions òptiques de gran velocitat, aquestes xarxes manquen de flexibilitat per suportar tràfic d’inferior granularitat, fet que provoca un pobre ús d'ample de banda. Per fer front al transport d'aquest tràfic heterogeni, les xarxes multicapa representen la millor solució. Les xarxes òptiques multicapa permeten optimitzar la capacitat mitjançant l'empaquetament de connexions de baixa velocitat dins de connexions òptiques de gran velocitat. Durant aquesta operació, es crea i modifica constantment una topologia virtual dinàmica gràcies al pla de control responsable d’aquestes operacions. Donada aquesta dinamicitat, un ús sub-òptim de recursos pot existir a la xarxa en un moment donat. En aquest context, una re-optimizació periòdica dels recursos utilitzats pot ser aplicada, millorant així l'ús de recursos. Aquesta tesi està dedicada a la caracterització, planificació, i re-optimització de xarxes òptiques multicapa de nova generació des d’un punt de vista unificat incloent optimització als nivells de capa física, capa òptica, capa virtual i pla de control. Concretament s'han desenvolupat models estadístics i de programació matemàtica i meta-heurístiques. Aquest objectiu principal s'ha assolit mitjançant cinc objectius concrets cobrint diversos temes oberts de recerca. En primer lloc, proposem una metodologia estadística per millorar el càlcul del factor Q en problemes d'assignació de ruta i longitud d'ona considerant interaccions físiques (IA-RWA). Amb aquest objectiu, proposem dos models estadístics per computar l'efecte XPM (el coll d'ampolla en termes de computació i complexitat) per problemes IA-RWA, demostrant la precisió d’ambdós models en el càlcul del factor Q en escenaris reals de tràfic. En segon lloc i fixant-nos a la capa òptica, presentem un nou particionament del conjunt de longituds d'ona que permet maximitzar, respecte el cas habitual, la quantitat de tràfic extra proveït en entorns de protecció compartida. Concretament, definim diversos models estadístics per estimar la quantitat de tràfic donat un grau de servei objectiu, i diferents models de planificació de xarxa amb l'objectiu de maximitzar els ingressos previstos i el valor actual net de la xarxa. Després de resoldre aquests problemes per xarxes reals, concloem que la nostra proposta maximitza ambdós objectius. En tercer lloc, afrontem el disseny de xarxes multicapa robustes davant de fallida simple a la capa IP/MPLS i als enllaços de fibra. Per resoldre aquest problema eficientment, proposem un enfocament basat en sobre-dimensionar l'equipament de la capa IP/MPLS i recuperar la connectivitat i el comparem amb la solució convencional basada en duplicar la capa IP/MPLS. Després de comparar solucions mitjançant models ILP i heurístiques, concloem que la nostra solució permet obtenir un estalvi significatiu en termes de costos de desplegament. Com a quart objectiu, introduïm un mecanisme adaptatiu per reduir l'ús de ports opto-electrònics (O/E) en xarxes multicapa sota escenaris de tràfic dinàmic. Una formulació ILP i diverses heurístiques són desenvolupades per resoldre aquest problema, que permet reduir significativament l’ús de ports O/E en temps molt curts. Finalment, adrecem el problema de disseny resilient del pla de control GMPLS. Després de proposar un nou model analític per quantificar la resiliència en topologies mallades de pla de control, usem aquest model per proposar un problema de disseny de pla de control. Proposem un procediment iteratiu lineal i una heurística i els usem per resoldre instàncies reals, arribant a la conclusió que es pot reduir significativament la quantitat d'enllaços del pla de control sense afectar la qualitat de servei a la xarxa.The explosion of IP traffic due to the increase of IP-based multimedia services such as HDTV or video conferencing poses new challenges to network operators to provide a cost-effective data transmission. Although Dense Wavelength Division Multiplexing (DWDM) meshed transport networks support high-speed optical connections, these networks lack the flexibility to support sub-wavelength traffic leading to poor bandwidth usage. To cope with the transport of that huge and heterogeneous amount of traffic, multilayer networks represent the most accepted architectural solution. Multilayer optical networks allow optimizing network capacity by means of packing several low-speed traffic streams into higher-speed optical connections (lightpaths). During this operation, a dynamic virtual topology is created and modified the whole time thanks to a control plane responsible for the establishment, maintenance, and release of connections. Because of this dynamicity, a suboptimal allocation of resources may exist at any time. In this context, a periodically resource reallocation could be deployed in the network, thus improving network resource utilization. This thesis is devoted to the characterization, planning, and re-optimization of next-generation multilayer networks from an integral perspective including physical layer, optical layer, virtual layer, and control plane optimization. To this aim, statistical models, mathematical programming models and meta-heuristics are developed. More specifically, this main objective has been attained by developing five goals covering different open issues. First, we provide a statistical methodology to improve the computation of the Q-factor for impairment-aware routing and wavelength assignment problems (IA-RWA). To this aim we propose two statistical models to compute the Cross-Phase Modulation variance (which represents the bottleneck in terms of computation time and complexity) in off-line and on-line IA-RWA problems, proving the accuracy of both models when computing Q-factor values in real traffic scenarios. Second and moving to the optical layer, we present a new wavelength partitioning scheme that allows maximizing the amount of extra traffic provided in shared path protected environments compared with current solutions. Specifically, we define several statistical models to estimate the traffic intensity given a target grade of service, and different network planning problems for maximizing the expected revenues and net present value. After solving these problems for real networks, we conclude that our proposed scheme maximizes both revenues and NPV. Third, we tackle the design of survivable multilayer networks against single failures at the IP/MPLS layer and WSON links. To efficiently solve this problem, we propose a new approach based on over-dimensioning IP/MPLS devices and lightpath connectivity and recovery and we compare it against the conventional solution based on duplicating backbone IP/MPLS nodes. After evaluating both approaches by means of ILP models and heuristic algorithms, we conclude that our proposed approach leads to significant CAPEX savings. Fourth, we introduce an adaptive mechanism to reduce the usage of opto-electronic (O/E) ports of IP/MPLS-over-WSON multilayer networks in dynamic scenarios. A ILP formulation and several heuristics are developed to solve this problem, which allows significantly reducing the usage of O/E ports in very short running times. Finally, we address the design of resilient control plane topologies in GMPLS-enabled transport networks. After proposing a novel analytical model to quantify the resilience in mesh control plane topologies, we use this model to propose a problem to design the control plane topology. An iterative model and a heuristic are proposed and used to solve real instances, concluding that a significant reduction in the number of control plane links can be performed without affecting the quality of service of the network

Provisioning lightpath demands with quality of protection grades in WDM optical networks

Master'sMASTER OF ENGINEERIN

Survivability stategies in all optical networks.

Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, 2006.Thesis (M.Sc.)-University of KwaZulu-Natal, 2006.Recent advances in fiber optics technology have enabled extremely high-speed transport of different forms of data, on multiple wavelengths of an optical fiber, using Dense Wavelength Division Multiplexing (DWDM). It has now become possible to deploy high-speed, multi-service networks using DWDM technology. As the amount of traffic carried has increased, any single failure can be catastrophic. Survivability becomes indispensable in such networks. Therefore, it is imperative to design networks that can quickly and efficiently recover from failures. Most research to date in survivable optical network design and operation focuses on single link failures, however, the occurrence of multiple-link failures are not uncommon in networks today. Multi-link failure scenarios can arise out of two common situations. First, an arbitrary link may fail in the network, and before that link can be repaired, another link fails, thus creating a multi-link failure sequence. Secondly, it might happen in practice that two distinct physical links may be routed via the same common duct or physical channel. A failure at that shared physical location creates a logical multiple-link failure. In this dissertation, we conduct an intensive study of mechanisms for achieving survivability in optical networks. From the many mechanisms presented in the literature the focus of this work was on protection as a mechanism of survivability. In particular four protection schemes were simulated and their results analyzed to ascertain which protection scheme achieves the best survivability in terms of number of wavelengths recovered for a specific failure scenario. A model network was chosen and the protection schemes were evaluated for both single and multiple link and node failures. As an indicator of the performance of these protection schemes over a period of time average service availability and average loss in traffic for each protection scheme was also simulated. Further simulations were conducted to observe the percentage link and node utilization of each scheme hence allowing us to determine the strain each protection scheme places on network resources when traffic in the network increases. Finally based on these simulation results, recommendations of which protection scheme and under what failure conditions they should be used are made.Recent advances in fiber optics technology have enabled extremely high-speed transpor

Multi-ring SDH network design over optical mesh networks

Ankara : The Department of Electrical and Electronics Engineering and Sciences of Bilkent University, 2002.Thesis (Master's) -- Bilkent University, 2002.Includes bibliographical references leaves 84-87.The evolution of networks in telecommunications has brought on the importance of design techniques to obtain survivable and cost-effective transportation networks. In this thesis, we study Synchronous Digital Hierarchy (SDH) ring design problem with an interconnected multi-ring architecture overlaid over an optical mesh network. We decouple the problem into two sub-problems: the first problem is the SDH ring selection, and the second problem is the mapping of these rings onto the physical mesh topology. In this structure, the logical topology consists of SDH Add/Drop Multiplexers (ADMs) and Digital Cross-Connects (DXCs), and the physical topology consists of Optical Cross-Connects (OXCs). The ring selection problem is to choose the rings that give minimum inter-ring traffic in the network. Since inter-ring traffic increases the network cost and complexity, we aim to minimize the inter-ring traffic. We propose a greedy heuristic algorithm for this problem that finds a solution subject to the constraint that the number of nodes on each ring is limited. Numerical results on the ring design problem are presented for different topologies. Once the logical topology is obtained, resilient mapping of SDH rings onto the mesh physical topology is formulated as a Mixed Integer Linear Programming (MILP) problem. In order to guarantee proper operation of SDH ring protection against all single failures, each link on an SDH ring must be mapped onto a lightpath which is link and node disjoint from all other lightpaths comprising the same ring. The objective of this mapping is to minimize the total fiber cost in the network. We also apply a post-processing algorithm to eliminate redundant rings. The postprocessing algorithm is very useful to reduce the cost. We evaluate the performance of our design algorithm for different networks.Tan, Tuba AkıncılarM.S

A resilience-based comparative study between optical burst switching and optical circuit switching technologies

Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. J. A. Hernández, J. Aracil, V. López, J. F. Palacios, and O. G. de Dios, "A resilience-based comparative study between optical burst switching and optical circuit switching technologies", in International Conference on Transparent Optical Networks, 2006, p. 231-234Internet operators and ISP providers have traditionally designed network resources following an over-planning policy, on attempts to maintain a desired grade of service and network availability, regardless of network failures. This work presents a comparative study of two resilience mechanisms in the design of optical networks either based on optical burst switching (OBS) or optical circuit switching (OCS): the M:N protection scheme with dedicated backup channels. It is further analysed and discussed the benefits and disadvantages of such mechanism based on an analytical mode

Survivability schemes for dynamic traffic in optical networks

Ph.DDOCTOR OF PHILOSOPH

Off-line and in-operation optical core networks planning

The ever increasing IP traffic volume has finally brought to light the high inefficiency of current wavelength-routed over rigid-grid optical networks in matching the client layer requirements. Such an issue results in the deployment of large-size, expensive and power-consuming Multiprotocol Label Switching (MPLS) layers to perform the required grooming/aggregation functionality. To deal with this problem, the emerging flexgrid technology, allowing for reduced size frequency grids, is being standardized. Flexgrid optical networks divide the spectrum into frequency slots providing finer granularity than rigid networks based on Dense Wavelength Division Multiplexing (DWDM). To find a feasible allocation, new Routing and Spectrum Allocation (RSA) algorithms for flexgrid optical networks need to be designed and evaluated. Furthermore, due to the flexibility of flexible optical networks, the aggregation functions and statistical multiplexing can be partially located in the optical layer. In addition, given the special characteristics of flexible optical networks, the traditional mechanisms for protection and recovery must be reformulated. Optical transport platforms are designed to facilitate the setting up and tearing down of optical connections (lightpaths). Combining remotely configurable optical cross-connects (OXCs) with a control plane provides the capability of automated lightpath set-up for regular provisioning, and real-time reaction to the failures, being thus able to reduce Operational Expenditures (OPEX). However, to exploit existing capacity, increase dynamicity, and provide automation in future networks, current management architectures, utilizing legacy Network Management Systems (NMS) need to be radically transformed. This thesis is devoted to design optical networks and to devise algorithms to operate them. Network design objective consists of: i. Analyzing the cost implications that a set of frequency slot widths have on the Capital Expenditures (CAPEX) investments required to deploy MPLS-over-flexgrid networks; ii. Studying recovery schemes, where a new recovery scheme specifically designed for flexgrid-based optical networks is proposed. As for network operation, we focus on: i. Studying provisioning, where two provisioning algorithms are proposed: the first one targets at solving the RSA problem in flexgrid networks, whereas the second one studies provisioning considering optical impairments in translucent DWDM networks; ii. Getting back to the recovery problem, we focus on algorithms to cope with restoration in dynamic scenarios. Several algorithms are proposed for both single layer and multilayer networks to be deployed in the centralized Path Computation Element (PCE); iii. One of the main problems in flexgrid networks is spectrum defragmentation. In view of that, we propose an algorithm to reallocate already established optical connections so as to make room for incoming requests. This algorithm is extended with elasticity to deal with time-varying traffic. The above algorithms are firstly implemented and validated by using simulation, and finally experimentally assessed in real test-beds. In view of PCE architectures do not facilitate network reconfiguration, we propose a control and management architecture to allow the network to be dynamically operated; network resources can be made available by reconfiguring and/or re-optimizing the network on demand and in real-time. We call that as in-operation network planning. It shall be mentioned that part of the work reported in this thesis has been done within the framework of several European and National projects, namely STRONGEST (FP7-247674), IDEALIST (FP7-ICT-2011-8), and GEANT (FP7-238875) funded by the European Commission, and ENGINE (TEC2008-02634) and ELASTIC (TEC2011-27310) funded by the Spanish Science Ministry.El volumen creciente del tráfico IP, finalmente, ha puesto de manifiesto la alta ineficiencia de las redes ópticas actuales de grid rígido basadas en WDM en la adecuación a los requisitos de capa de cliente. Dicho problema genera que se deba desplegar una red con capas MPLS de gran tamaño, costosa y de alto consumo energético para poder realizar la funcionalidad de agregación requerida. Para hacer frente a este problema, la tecnología flexgrid emergente, que permite grids con frecuencias de menor tamaño, está siendo estandarizada. Las redes ópticas flexgrid dividen el espectro en slots de frecuencia, lo que proporciona una granularidad más fina en comparación a las redes rígidas basadas en WDM. Para encontrar una asignación factible, nuevos algoritmos de enrutamiento y asignación de espectro (RSA) para redes ópticas flexgrid deben ser diseñados y evaluados. Además, debido a la flexibilidad de las redes ópticas flexibles, las funciones de agregación y de multiplexación estadística pueden ser parcialmente situadas en la capa óptica. Asimismo, dadas las características especiales de las redes ópticas flexibles, los mecanismos tradicionales de protección y recuperación deben reformularse. Las plataformas de transporte ópticas están diseñadas para facilitar la creación y destrucción de conexiones ópticas. La combinación de OXCs configurables remotamente con un plano de control, proporciona la capacidad de crear conexiones automáticamente para el aprovisionamiento habitual, y la reacción en tiempo real a los fallos, para así poder reducir el OPEX. Sin embargo, para aprovechar la capacidad existente, aumentar la dinamicidad y proporcionar automatización a las redes del futuro, las arquitecturas actuales de gestión, que utilizan sistemas legados de NMS, necesitan ser transformadas de manera radical. Esta tesis está dedicada al diseño de redes ópticas y a la creación de algoritmos para operarlas. El objetivo de diseño de red se compone de: 1. El análisis de las implicancias en el costo que tiene un conjunto de slots de frecuencia en el CAPEX necesario para implementar redes MPLS-over-flexgrid; 2. El estudio de esquemas de recuperación, donde se propone un nuevo esquema de recuperación diseñado específicamente para las redes ópticas basadas en flexgrid. En cuanto a la operación de la red: 1. El estudio de aprovisionamiento, donde se proponen dos algoritmos de aprovisionamiento: el primero de ellos tiene como objetivo solucionar el problema de RSA en redes flexgrid, mientras que el segundo estudia aprovisionamiento considerando la degradación óptica en redes WDM translúcidas; 2. Volviendo al problema de la recuperación, nos centramos en algoritmos de restauración para escenarios dinámicos. Se proponen varios algoritmos, tanto para redes mono-capa como multi-capa, que serán desplegados en un PCE centralizado; 3. Uno de los principales problemas en las redes flexgrid es la desfragmentación del espectro. Para ello, se propone un algoritmo para reasignar las conexiones ópticas ya establecidas con el fin de hacer espacio a las entrantes. Este algoritmo se extiende con elasticidad para ser utilizado en escenarios con tráfico variable en el tiempo. Los algoritmos anteriores son primero implementados y validados utilizando simulación, y finalmente son evaluados experimentalmente en testbeds reales. En vista de que las arquitecturas de PCE no facilitan la reconfiguración de la red, proponemos una arquitectura de control y gestión para permitir que la red pueda ser operada de forma dinámica; hacer que los recursos de la red estén disponibles mediante reconfiguración y/o re-optimización de la red bajo demanda y en tiempo real. A eso lo llamamos planificación en operación de la red. El trabajo presentado en esta tesis se ha realizado en el marco de proyectos europeos y nacionales: STRONGEST (FP7-247674), IDEALIST (FP7-2011-8), y GEANT (FP7-238875) financiados por la CE, y ENGINE (TEC2008-02634) y ELASTIC (TEC2011-27310) financiados por el MINEC