System integration for a novel positioning system using a model based control approach

This dissertation presents a model-based approach to perform system integration of a novel positioning sensing method, termed \u27Direct Position Sensing.\u27 Direct Position Sensing can actively monitor the planar position changes of motion control devices without the dependency of the conventional position sensor combined with kinematic model to estimate the planar position. Instead, Direct Position Sensing uses the technology of computer vision and digital display to directly monitor the planar position displacement of a motion control device by actively tracking the desired position of the device based on the displayed target showed on the digital screen. The integration of the computer vision as the feedback system to the motion controller, introduces intermittency and latency in the controller\u27s feedback loop. In order to integrate the slower computer vision sensor to the motion controller, a model-based controller architecture, Smith Predictor approach was first implemented to the Direct Position Sensing system. The Smith Predictor uses a mathematical plant model that is running in parallel with the actual plant so that the model predicts the plant output when the actual output of the system is unavailable. Due to the intermittency feedback of the system, a path prediction algorithm was developed to minimize the model residual during the intermittent feedback so that the tracking performance of the system can be improved. Furthermore, a model input corrector was also developed to correct the control action to the plant model based on the model residual to enhance the path prediction. Simulations and hardware experiments results show that the model-based strategy provides improved tracking performance of the system when latency and intermittency exist in the controller feedback loop

Design and implementation of event-based multi-rate controllers for networked control systems

Tesis por compendio[ES] Con esta tesis se pretende dar solución a algunos de los problemas más habituales que aparecen en los Sistemas de control basados en red (NCS) como son los retardos variables en el tiempo, las pérdidas y el desorden de paquetes, y la restricción de ancho de banda y de recursos computacionales y energéticos de los dispositivos que forman parte del sistema de control. Para ello se ha planteado la integración de técnicas de control multifrecuencial, de control basado en paquetes, de control basado en predictor y de control basado en eventos. Los diseños de control realizados se han simulado utilizando Matlab-Simulink y Truetime, se ha analizado su estabilidad mediante LMIs y QFT, y se han validado experimentalmente en un péndulo invertido, un robot cartesiano 3D y en robots móviles de bajo coste. El artículo 1 aborda el control basado en eventos, el cual minimiza el ancho de banda consumido en el NCS mediante un control basado en eventos periódicos y presenta un método para obtener sus parámetros óptimos para el sistema específico en que se utilice. Los artículos 2, 4 y 6 añaden el control basado en paquetes, así como el control multifrecuencia, que aborda problemas de falta de datos por bajo uso del sensor y los retardos, pérdidas y desórdenes de paquetes en la red. También afrontan, mediante tecnicas de predicción basadas en un filtro de Kalman multifrecuencia variable en el tiempo, los problemas de ruido y perturbaciones, así como la observación de los estados completos del sistema. El artículo 7 hace frente a un modelo no lineal que utiliza las anteriores soluciones junto con un filtro de Kalman extendido para presentar otro tipo de estructura para un vehículo autónomo que, gracias a la información futura obtenida mediante estas técnicas, puede realizar de forma remota tareas de alto nivel como es la toma de decisiones y la monitorización de variables. Los artículos 3 y 5, presentan una forma de obtener y analizar la respuesta en frecuencia de sistemas SISO multifrecuencia y estudian su comportamiento ante ciertas incertidumbres o problemas en la red haciendo uso de procedimientos QFT.[CA] Amb aquesta tesi es pretén donar solució a alguns dels problemes més habituals que apareixen als Sistemes de Control Basats en xarxa (NCS) com son els retards d'accés i transferència variables en el temps, les pèrdues y desordenament de paquets, i la restricció d'ampli de banda així com de recursos computacionals i energètics dels dispositius que foment part del sistema de control. Per tal de resoldre'ls s'ha plantejat la integració de tècniques de control multifreqüencial, de control basat en paquets, de control basat en predictor i de control basat en events. Els dissenys de control realitzats s'han simulat fent ús de Matlab-Simulink i de TrueTime, s'ha analitzat la seua estabilitat mitjançant LMIs i QFT, i s'han validat experimentalment en un pèndul invertit, un robot cartesià 3D i en robots mòbils de baix cost. L'article 1 aborda el control basat en events, el qual minimitza l'ampli de banda consumit a l'NCS mitjançant un control basat en events periòdics i presenta un mètode per a obtindré els seus paràmetres òptims per al sistema específic en el qual s'utilitza. Els articles 2, 4 i 6 afegeixen el control basat en paquets, així com el control multifreqüència, que aborda problemes de falta de dades per el baix us del sensor i els retards, pèrdues i desordre de paquets en la xarxa. També afronten, mitjançant tècniques de predicció basades en un filtre de Kalman multifreqüència variable en el temps. Els problemes de soroll i pertorbacions, així com la observació dels estats complets del sistema. L'article 7 fa referència a un model no lineal que utilitza les anteriors solucions junt a un filtre de Kalman estès per a presentar altre tipus d'estructura per a un vehicle autònom que, gracies a la informació futura obtinguda mitjançant aquestes tècniques, pot realitzar de manera remota tasques d'alt nivell com son la presa de decisions i la monitorització de variables. Els articles 3 y 5 presenten la manera d'obtindre i analitzar la resposta en frequencia de sistemes SISO multifreqüència i estudien el seu comportament front a certes incerteses o problemes en la xarxa fent us de procediments QFT.[EN] This thesis attempts to solve some of the most frequent issues that appear in Networked Control Systems (NCS), such as time-varying delays, packet losses and packet disorders and the bandwidth limitation. Other frequent problems are scarce computational and energy resources of the local system devices. Thus, it is proposed to integrate multirate control, packet-based control, predictor-based control and event-based control techniques. The control designs have been simulated using Matlab-Simulink and Truetime, the stability has been analysed by LMIs and QFT, and the experimental validation has been done on an inverted pendulum, a 3D cartesian robot and in low-cost mobile robots. Paper 1 addresses event-based control, which minimizes the bandwidth consumed in NCS through a periodic event-triggered control and presents a method to obtain the optimal parameters for the specific system used. Papers 2, 4 and 6 include packet-based control and multirate control, addressing problems such as network delays, packet dropouts and packet disorders, and the scarce data due to low sensor usage in order to save battery in sensing tasks and transmissions of the sensed data. Also addressed, is how despite the existence of measurement noise and disturbances, time-varying dual-rate Kalman filter based prediction techniques observe the complete state of the system. Paper 7 tackles a non-linear model that uses all the previous solutions together with an extended Kalman filter to present another type of structure for an autonomous vehicle that, due to future information obtained through these techniques, can remotely carry out high level tasks, such as decision making and monitoring of variables. Papers 3 and 5, present a method for obtaining and analyzing the SISO dual-rate frequency response and using QFT procedures to study its behavior when faced with specific uncertainties or network problems.This work was supported by the Spanish Ministerio de Economía y Competitividad under Grant referenced TEC2012-31506.Alcaina Acosta, JJ. (2020). Design and implementation of event-based multi-rate controllers for networked control systems [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/159884TESISCompendi

Optimized state feedback regulation of 3DOF helicopter system via extremum seeking

In this paper, an optimized state feedback regulation of a 3 degree of freedom (DOF) helicopter is designed via extremum seeking (ES) technique. Multi-parameter ES is applied to optimize the tracking performance via tuning State Vector Feedback with Integration of the Control Error (SVFBICE). Discrete multivariable version of ES is developed to minimize a cost function that measures the performance of the controller. The cost function is a function of the error between the actual and desired axis positions. The controller parameters are updated online as the optimization takes place. This method significantly decreases the time in obtaining optimal controller parameters. Simulations were conducted for the online optimization under both fixed and varying operating conditions. The results demonstrate the usefulness of using ES for preserving the maximum attainable performance

Applications of MATLAB in Science and Engineering

The book consists of 24 chapters illustrating a wide range of areas where MATLAB tools are applied. These areas include mathematics, physics, chemistry and chemical engineering, mechanical engineering, biological (molecular biology) and medical sciences, communication and control systems, digital signal, image and video processing, system modeling and simulation. Many interesting problems have been included throughout the book, and its contents will be beneficial for students and professionals in wide areas of interest

Model-based control for high-tech mechatronic systems

Motion systems are mechanical systems with actuators with the primary function to position a load. The actuator can be either hydraulic, pneumatic, or electric. The feedback controller is typically designed using frequency domain techniques, in particular via manual loop-shaping. In addition to the feedback controller, a feedforward controller is often implemented with acceleration, velocity, and friction feedforward for the reference signal. This chapter provides an overview of a systematic control design procedure for motion systems that has proven its use in industrial motion control practise. A step-by-step procedure is presented that gradually extends single-input single-output (SISO) loop-shaping to the multi-input multi-output (MIMO) situation. This step-by-step procedure consists of interaction analysis, decoupling, independent SISO design, sequential SISO design, and finally, norm-based MIMO design. Extreme ultraviolet is a key technology for next-generation lithography

Formulation of Model-Based Optimal Control for Practical Applications

Ph.DDOCTOR OF PHILOSOPH

Advances in PID Control

Since the foundation and up to the current state-of-the-art in control engineering, the problems of PID control steadily attract great attention of numerous researchers and remain inexhaustible source of new ideas for process of control system design and industrial applications. PID control effectiveness is usually caused by the nature of dynamical processes, conditioned that the majority of the industrial dynamical processes are well described by simple dynamic model of the first or second order. The efficacy of PID controllers vastly falls in case of complicated dynamics, nonlinearities, and varying parameters of the plant. This gives a pulse to further researches in the field of PID control. Consequently, the problems of advanced PID control system design methodologies, rules of adaptive PID control, self-tuning procedures, and particularly robustness and transient performance for nonlinear systems, still remain as the areas of the lively interests for many scientists and researchers at the present time. The recent research results presented in this book provide new ideas for improved performance of PID control applications

Advancements in Real-Time Simulation of Power and Energy Systems

Modern power and energy systems are characterized by the wide integration of distributed generation, storage and electric vehicles, adoption of ICT solutions, and interconnection of different energy carriers and consumer engagement, posing new challenges and creating new opportunities. Advanced testing and validation methods are needed to efficiently validate power equipment and controls in the contemporary complex environment and support the transition to a cleaner and sustainable energy system. Real-time hardware-in-the-loop (HIL) simulation has proven to be an effective method for validating and de-risking power system equipment in highly realistic, flexible, and repeatable conditions. Controller hardware-in-the-loop (CHIL) and power hardware-in-the-loop (PHIL) are the two main HIL simulation methods used in industry and academia that contribute to system-level testing enhancement by exploiting the flexibility of digital simulations in testing actual controllers and power equipment. This book addresses recent advances in real-time HIL simulation in several domains (also in new and promising areas), including technique improvements to promote its wider use. It is composed of 14 papers dealing with advances in HIL testing of power electronic converters, power system protection, modeling for real-time digital simulation, co-simulation, geographically distributed HIL, and multiphysics HIL, among other topics