Fault Secure Encoder and Decoder for NanoMemory Applications

Memory cells have been protected from soft errors for more than a decade; due to the increase in soft error rate in logic circuits, the encoder and decoder circuitry around the memory blocks have become susceptible to soft errors as well and must also be protected. We introduce a new approach to design fault-secure encoder and decoder circuitry for memory designs. The key novel contribution of this paper is identifying and defining a new class of error-correcting codes whose redundancy makes the design of fault-secure detectors (FSD) particularly simple. We further quantify the importance of protecting encoder and decoder circuitry against transient errors, illustrating a scenario where the system failure rate (FIT) is dominated by the failure rate of the encoder and decoder. We prove that Euclidean geometry low-density parity-check (EG-LDPC) codes have the fault-secure detector capability. Using some of the smaller EG-LDPC codes, we can tolerate bit or nanowire defect rates of 10% and fault rates of 10^(-18) upsets/device/cycle, achieving a FIT rate at or below one for the entire memory system and a memory density of 10^(11) bit/cm^2 with nanowire pitch of 10 nm for memory blocks of 10 Mb or larger. Larger EG-LDPC codes can achieve even higher reliability and lower area overhead

Concatenated Turbo/LDPC codes for deep space communications: performance and implementation

Deep space communications require error correction codes able to reach extremely low bit-error-rates, possibly with a steep waterfall region and without error floor. Several schemes have been proposed in the literature to achieve these goals. Most of them rely on the concatenation of different codes that leads to high hardware implementation complexity and poor resource sharing. This work proposes a scheme based on the concatenation of non-custom LDPC and turbo codes that achieves excellent error correction performance. Moreover, since both LDPC and turbo codes can be decoded with the BCJR algorithm, our preliminary results show that an efficient hardware architecture with high resource reuse can be designe

A Novel Stochastic Decoding of LDPC Codes with Quantitative Guarantees

Low-density parity-check codes, a class of capacity-approaching linear codes, are particularly recognized for their efficient decoding scheme. The decoding scheme, known as the sum-product, is an iterative algorithm consisting of passing messages between variable and check nodes of the factor graph. The sum-product algorithm is fully parallelizable, owing to the fact that all messages can be update concurrently. However, since it requires extensive number of highly interconnected wires, the fully-parallel implementation of the sum-product on chips is exceedingly challenging. Stochastic decoding algorithms, which exchange binary messages, are of great interest for mitigating this challenge and have been the focus of extensive research over the past decade. They significantly reduce the required wiring and computational complexity of the message-passing algorithm. Even though stochastic decoders have been shown extremely effective in practice, the theoretical aspect and understanding of such algorithms remains limited at large. Our main objective in this paper is to address this issue. We first propose a novel algorithm referred to as the Markov based stochastic decoding. Then, we provide concrete quantitative guarantees on its performance for tree-structured as well as general factor graphs. More specifically, we provide upper-bounds on the first and second moments of the error, illustrating that the proposed algorithm is an asymptotically consistent estimate of the sum-product algorithm. We also validate our theoretical predictions with experimental results, showing we achieve comparable performance to other practical stochastic decoders.Comment: This paper has been submitted to IEEE Transactions on Information Theory on May 24th 201

Configurable LDPC Decoder Architecture for Regular and Irregular Codes

Low Density Parity Check (LDPC) codes are one of the best error correcting codes that enable the future generations of wireless devices to achieve higher data rates with excellent quality of service. This paper presents two novel flexible decoder architectures. The first one supports (3, 6) regular codes of rate 1/2 that can be used for different block lengths. The second decoder is more general and supports both regular and irregular LDPC codes with twelve combinations of code lengths −648, 1296, 1944-bits and code rates-1/2, 2/3, 3/4, 5/6- based on the IEEE 802.11n standard. All codes correspond to a block-structured parity check matrix, in which the sub-blocks are either a shifted identity matrix or a zero matrix. Prototype architectures for both LDPC decoders have been implemented and tested on a Xilinx field programmable gate array.NokiaNational Science Foundatio

A 2.0 Gb/s Throughput Decoder for QC-LDPC Convolutional Codes

This paper propose a decoder architecture for low-density parity-check convolutional code (LDPCCC). Specifically, the LDPCCC is derived from a quasi-cyclic (QC) LDPC block code. By making use of the quasi-cyclic structure, the proposed LDPCCC decoder adopts a dynamic message storage in the memory and uses a simple address controller. The decoder efficiently combines the memories in the pipelining processors into a large memory block so as to take advantage of the data-width of the embedded memory in a modern field-programmable gate array (FPGA). A rate-5/6 QC-LDPCCC has been implemented on an Altera Stratix FPGA. It achieves up to 2.0 Gb/s throughput with a clock frequency of 100 MHz. Moreover, the decoder displays an excellent error performance of lower than $10^{-13}$ at a bit-energy-to-noise-power-spectral-density ratio ($E_b/N_0$) of 3.55 dB.Comment: accepted to IEEE Transactions on Circuits and Systems

Deriving Good LDPC Convolutional Codes from LDPC Block Codes

Low-density parity-check (LDPC) convolutional codes are capable of achieving excellent performance with low encoding and decoding complexity. In this paper we discuss several graph-cover-based methods for deriving families of time-invariant and time-varying LDPC convolutional codes from LDPC block codes and show how earlier proposed LDPC convolutional code constructions can be presented within this framework. Some of the constructed convolutional codes significantly outperform the underlying LDPC block codes. We investigate some possible reasons for this "convolutional gain," and we also discuss the --- mostly moderate --- decoder cost increase that is incurred by going from LDPC block to LDPC convolutional codes.Comment: Submitted to IEEE Transactions on Information Theory, April 2010; revised August 2010, revised November 2010 (essentially final version). (Besides many small changes, the first and second revised versions contain corrected entries in Tables I and II.

Non Binary Low Density Parity Check Codes Decoding Over Galois Field

Conventional LDPC codes have a low decoding complexity but may have high encoding complexity. The encoding complexity is typically of the order O(n2)[5]. Also high storage space may be required to explicitly store the generator matrix. For long blocknbsp lengths the storage space required would be huge. The above factors make the implementation of the Conventional LDPC codes less attractive. These codes are usually decoded using the sum-product algorithm, which is anbsp message passing algorithm working on the Tanner graph of the code[5]. The sparseness of the parity check matrix is essential for attaining good performance with sum-product decoding. The time complexity of the sum- product algorithm is linear in code length. This property makes it possible to implement a practical decoder for long lengths.nbs

Mixed Precision Multi-frame Parallel Low-Density Parity-Check Code Decoder

As the demand for high speed and high quality connectivity is increasing exponentially, channels are getting more and more crowded. The need for a high performance and low error floor channel decoder is apparent. Low-density parity-check code (LDPC) is a linear error correction code that can reach near Shannon limit. In this work, LDPC code construction and decoding algorithms are discussed, the LDPC decoder, in fully parallel and partial parallel, was implemented, and the features and issues related to corresponding architecture are analyzed. Furthermore, a multi-frame processing approach, based on pipelining and out-of-order processing, is proposed. The implemented decoder achieves 12.6 Gbps at 3.0 dB SNR. The mixed precision scheme is explored by adding precision control and alignment units before and after check node units (CNU) to improve performance, as well as error floor. By mixing the 6-bit and 5-bit precision CNUs at 1:1 ratio, the decoder reaches ~0.5 dB lower FER and BER while retaining a low error floor