16,846 research outputs found
Separation Framework: An Enabler for Cooperative and D2D Communication for Future 5G Networks
Soaring capacity and coverage demands dictate that future cellular networks
need to soon migrate towards ultra-dense networks. However, network
densification comes with a host of challenges that include compromised energy
efficiency, complex interference management, cumbersome mobility management,
burdensome signaling overheads and higher backhaul costs. Interestingly, most
of the problems, that beleaguer network densification, stem from legacy
networks' one common feature i.e., tight coupling between the control and data
planes regardless of their degree of heterogeneity and cell density.
Consequently, in wake of 5G, control and data planes separation architecture
(SARC) has recently been conceived as a promising paradigm that has potential
to address most of aforementioned challenges. In this article, we review
various proposals that have been presented in literature so far to enable SARC.
More specifically, we analyze how and to what degree various SARC proposals
address the four main challenges in network densification namely: energy
efficiency, system level capacity maximization, interference management and
mobility management. We then focus on two salient features of future cellular
networks that have not yet been adapted in legacy networks at wide scale and
thus remain a hallmark of 5G, i.e., coordinated multipoint (CoMP), and
device-to-device (D2D) communications. After providing necessary background on
CoMP and D2D, we analyze how SARC can particularly act as a major enabler for
CoMP and D2D in context of 5G. This article thus serves as both a tutorial as
well as an up to date survey on SARC, CoMP and D2D. Most importantly, the
article provides an extensive outlook of challenges and opportunities that lie
at the crossroads of these three mutually entangled emerging technologies.Comment: 28 pages, 11 figures, IEEE Communications Surveys & Tutorials 201
Lightweight Synchronization Algorithm with Self-Calibration for Industrial LORA Sensor Networks
Wireless sensor and actuator networks are gaining momentum in the era of
Industrial Internet of Things IIoT. The usage of the close-loop data from
sensors in the manufacturing chain is extending the common monitoring scenario
of the Wireless Sensors Networks WSN where data were just logged. In this paper
we present an accurate timing synchronization for TDMA implemented on the state
of art IoT radio, such as LoRa, that is a good solution in industrial
environments for its high robustness. Experimental results show how it is
possible to modulate the drift correction and keep the synchronization error
within the requirements
Self-Synchronization in Duty-cycled Internet of Things (IoT) Applications
In recent years, the networks of low-power devices have gained popularity.
Typically these devices are wireless and interact to form large networks such
as the Machine to Machine (M2M) networks, Internet of Things (IoT), Wearable
Computing, and Wireless Sensor Networks. The collaboration among these devices
is a key to achieving the full potential of these networks. A major problem in
this field is to guarantee robust communication between elements while keeping
the whole network energy efficient. In this paper, we introduce an extended and
improved emergent broadcast slot (EBS) scheme, which facilitates collaboration
for robust communication and is energy efficient. In the EBS, nodes
communication unit remains in sleeping mode and are awake just to communicate.
The EBS scheme is fully decentralized, that is, nodes coordinate their wake-up
window in partially overlapped manner within each duty-cycle to avoid message
collisions. We show the theoretical convergence behavior of the scheme, which
is confirmed through real test-bed experimentation.Comment: 12 Pages, 11 Figures, Journa
LPDQ: a self-scheduled TDMA MAC protocol for one-hop dynamic lowpower wireless networks
Current Medium Access Control (MAC) protocols for data collection scenarios with a large number of nodes that generate bursty traffic are based on Low-Power Listening (LPL) for network synchronization and Frame Slotted ALOHA (FSA) as the channel access mechanism. However, FSA has an efficiency bounded to 36.8% due to contention effects, which reduces packet throughput and increases energy consumption. In this paper, we target such scenarios by presenting Low-Power Distributed Queuing (LPDQ), a highly efficient and low-power MAC protocol. LPDQ is able to self-schedule data transmissions, acting as a FSA MAC under light traffic and seamlessly converging to a Time Division Multiple Access (TDMA) MAC under congestion. The paper presents the design principles and the implementation details of LPDQ using low-power commercial radio transceivers. Experiments demonstrate an efficiency close to 99% that is independent of the number of nodes and is fair in terms of resource allocation.Peer ReviewedPostprint (author’s final draft
Slotted ALOHA Overlay on LoRaWAN: a Distributed Synchronization Approach
LoRaWAN is one of the most promising standards for IoT applications.
Nevertheless, the high density of end-devices expected for each gateway, the
absence of an effective synchronization scheme between gateway and end-devices,
challenge the scalability of these networks. In this article, we propose to
regulate the communication of LoRaWAN networks using a Slotted-ALOHA (S-ALOHA)
instead of the classic ALOHA approach used by LoRa. The implementation is an
overlay on top of the standard LoRaWAN; thus no modification in pre-existing
LoRaWAN firmware and libraries is necessary. Our method is based on a novel
distributed synchronization service that is suitable for low-cost IoT
end-nodes. S-ALOHA supported by our synchronization service significantly
improves the performance of traditional LoRaWAN networks regarding packet loss
rate and network throughput.Comment: 4 pages, 8 figure
Design Aspects of An Energy-Efficient, Lightweight Medium Access Control Protocol for Wireless Sensor Networks
This document gives an overview of the most relevant design aspects of the lightweight medium access control (LMAC) protocol [16] for wireless sensor networks (WSNs). These aspects include selfconfiguring and localized operation of the protocol, time synchronization in multi-hop networks, network setup and strategies to reduce latency.\ud
The main goal in designing a MAC protocol for WSNs is to minimize energy waste - due to collisions of messages and idle listening - , while limiting latency and loss of data throughput. It is shown that the LMAC protocol performs well on energy-efficiency and delivery ratio [19] and can\ud
ensure a long-lived, self-configuring network of battery-powered wireless sensors.\ud
The protocol is based upon scheduled access, in which each node periodically gets a time slot, during which it is allowed to transmit. The protocol does not depend on central managers to assign time slots to nodes.\ud
WSNs are assumed to be multi-hop networks, which allows for spatial reuse of time slots, just like frequency reuse in GSM cells. In this document, we present a distributed algorithm that allows nodes to find unoccupied time slots, which can be used without causing collision or interference to other nodes. Each node takes one time slot in control to\ud
carry out its data transmissions. Latency is affected by the actual choice of controlled time slot. We present time slot choosing strategies, which ensure a low latency for the most common data traffic in WSNs: reporting of sensor readings to central sinks
D-SLATS: Distributed Simultaneous Localization and Time Synchronization
Through the last decade, we have witnessed a surge of Internet of Things
(IoT) devices, and with that a greater need to choreograph their actions across
both time and space. Although these two problems, namely time synchronization
and localization, share many aspects in common, they are traditionally treated
separately or combined on centralized approaches that results in an ineffcient
use of resources, or in solutions that are not scalable in terms of the number
of IoT devices. Therefore, we propose D-SLATS, a framework comprised of three
different and independent algorithms to jointly solve time synchronization and
localization problems in a distributed fashion. The First two algorithms are
based mainly on the distributed Extended Kalman Filter (EKF) whereas the third
one uses optimization techniques. No fusion center is required, and the devices
only communicate with their neighbors. The proposed methods are evaluated on
custom Ultra-Wideband communication Testbed and a quadrotor, representing a
network of both static and mobile nodes. Our algorithms achieve up to three
microseconds time synchronization accuracy and 30 cm localization error
Seamless roaming and guaranteed communication using a synchronized single-hop multi-gateway 802.15.4e TSCH network
Industrial wireless sensor networks (WSNs) are being used to improve the
efficiency, productivity and safety of industrial processes. An open standard
that is commonly used in such cases is IEEE 802.15.4e. Its TSCH mode employs a
time synchronized based MAC scheme together with channel hopping to alleviate
the impact of channel fading. Until now, most of the industrial WSNs have been
designed to only support static nodes and are not able to deal with mobility.
In this paper, we show how a single-hop, multi-gateway IEEE 802.15.4e TSCH
network architecture can tackle the mobility problem. We introduce the Virtual
Grand Master (VGM) concept that moves the synchronization point from separated
Backbone Border Routers (BBRs) towards the backbone network. With time
synchronization of all BBRs, mobile nodes can roam from one BBR to another
without time desynchronization. In addition to time synchronization, we
introduce a mechanism to synchronize the schedules between BBRs to support fast
handover of mobile nodes.Comment: Short paper version of a paper submitted to Ad-Hoc Networks Journal
by Elsevie
- …