Design for Test and Hardware Security Utilizing Tester Authentication Techniques

Design-for-Test (DFT) techniques have been developed to improve testability of integrated circuits. Among the known DFT techniques, scan-based testing is considered an efficient solution for digital circuits. However, scan architecture can be exploited to launch a side channel attack. Scan chains can be used to access a cryptographic core inside a system-on-chip to extract critical information such as a private encryption key. For a scan enabled chip, if an attacker is given unlimited access to apply all sorts of inputs to the Circuit-Under-Test (CUT) and observe the outputs, the probability of gaining access to critical information increases. In this thesis, solutions are presented to improve hardware security and protect them against attacks using scan architecture. A solution based on tester authentication is presented in which, the CUT requests the tester to provide a secret code for authentication. The tester authentication circuit limits the access to the scan architecture to known testers. Moreover, in the proposed solution the number of attempts to apply test vectors and observe the results through the scan architecture is limited to make brute-force attacks practically impossible. A tester authentication utilizing a Phase Locked Loop (PLL) to encrypt the operating frequency of both DUT/Tester has also been presented. In this method, the access to the critical security circuits such as crypto-cores are not granted in the test mode. Instead, a built-in self-test method is used in the test mode to protect the circuit against scan-based attacks. Security for new generation of three-dimensional (3D) integrated circuits has been investigated through 3D simulations COMSOL Multiphysics environment. It is shown that the process of wafer thinning for 3D stacked IC integration reduces the leakage current which increases the chip security against side-channel attacks

Phase Locking Authentication for Scan Architecture

Scan design is a widely used Design for Testability (DfT) approach for digital circuits. It provides a high level of controllability and observability resulting in a high fault coverage. To achieve a high level of testability, scan architecture must provide access to the internal nodes of the circuit-under-test (CUT). This access however leads to vulnerability in the security of the CUT. If an unrestricted access is provided through a scan architecture, unlimited test vectors can be applied to the CUT and its responses can be captured. Such an unrestricted access to the CUT can potentially undermine the security of the critical information stored in the CUT. There is a need to secure scan architecture to prevent hardware attacks however a secure solution may limit the CUT testability. There is a trade-off between security and testability, therefore, a secure scan architecture without hindering its controllability and observability is required. Three solutions to secure scan architecture have been proposed in this thesis. In the first method, the tester is authenticated and the number of authentication attempts has been limited. In the second method, a Phase Locked Loop (PLL) is utilized to secure scan architecture. In the third method, the scan architecture is secured through a clock and data recovery (CDR) technique. This is a manuscript based thesis and the results of this study have been published in two conference proceedings. The latest results have also been prepared as an article for submission to a high rank conference

Design for pre-bond testability in 3D integrated circuits

In this dissertation we propose several DFT techniques specific to 3D stacked IC systems. The goal has explicitly been to create techniques that integrate easily with existing IC test systems. Specifically, this means utilizing scan- and wrapper-based techniques, two foundations of the digital IC test industry. First, we describe a general test architecture for 3D ICs. In this architecture, each tier of a 3D design is wrapped in test control logic that both manages tier test pre-bond and integrates the tier into the large test architecture post-bond. We describe a new kind of boundary scan to provide the necessary test control and observation of the partial circuits, and we propose a new design methodology for test hardcore that ensures both pre-bond functionality and post-bond optimality. We present the application of these techniques to the 3D-MAPS test vehicle, which has proven their effectiveness. Second, we extend these DFT techniques to circuit-partitioned designs. We find that boundary scan design is generally sufficient, but that some 3D designs require special DFT treatment. Most importantly, we demonstrate that the functional partitioning inherent in 3D design can potentially decrease the total test cost of verifying a circuit. Third, we present a new CAD algorithm for designing 3D test wrappers. This algorithm co-designs the pre-bond and post-bond wrappers to simultaneously minimize test time and routing cost. On average, our algorithm utilizes over 90% of the wires in both the pre-bond and post-bond wrappers. Finally, we look at the 3D vias themselves to develop a low-cost, high-volume pre-bond test methodology appropriate for production-level test. We describe the shorting probes methodology, wherein large test probes are used to contact multiple small 3D vias. This technique is an all-digital test method that integrates seamlessly into existing test flows. Our experimental results demonstrate two key facts: neither the large capacitance of the probe tips nor the process variation in the 3D vias and the probe tips significantly hinders the testability of the circuits. Taken together, this body of work defines a complete test methodology for testing 3D ICs pre-bond, eliminating one of the key hurdles to the commercialization of 3D technology.PhDCommittee Chair: Lee, Hsien-Hsin; Committee Member: Bakir, Muhannad; Committee Member: Lim, Sung Kyu; Committee Member: Vuduc, Richard; Committee Member: Yalamanchili, Sudhaka

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Thermal-Aware Test Schedule and TAM Co-Optimization for Three-Dimensional IC

[[abstract]]Testing is regarded as one of the most difficult challenges for three-dimensional integrated circuits (3D ICs). In this paper, we want to optimize the cost of TAM (test access mechanism) and the test time for 3D IC. We used both greedy and simulated annealing algorithms to solve this optimization problem. We compare the results of two assumptions: soft-die mode and hard-die mode. The former assumes that the DfT of dies cannot be changed, while the latter assumes that the DfT of dies can be adjusted. The results show that thermal-aware cooptimization is essential to decide the optimal TAM and test schedule. Blindly adding TAM cannot reduce the total test cost due to temperature constraints. Another conclusion is that soft-die mode is more effective than hard-die mode to reduce the total test cost for 3D IC.[[notice]]補正完畢[[booktype]]電子

Test Planning for 3D SICs using ILP

In this paper we propose a test planning scheme for corebased 3D stacked integrated circuits where the total test cost for wafer sort of each individual chip and the test cost of the complete stack at package test is minimized. We use an Integer Linear Programming (ILP) model to find the optimal test cost, which is given as the weighted sum of the test time and the test access mechanism (TAM). As ILP is time consuming, we use a scheme to bound the test time and the TAM such that the search space is reduced. The proposed bounding scheme and the ILP model were applied on several ITC’02 benchmarks and the results show that optimal solutions were obtained at low computation time

Test Planning and Test Access Mechanism Design for 3D SICs

In this paper we propose a scheme for test planning and test access mechanism (TAM) design for stacked integrated circuits (SICs) that are designed in a core-based manner. Our scheme minimizes the test cost, which is given as the weighted sum of the test time and the TAM width. The test cost is evaluated for a test flow that consists of a wafer sort test of each individual chip and a package test of the complete stack of chips. We use an Integer Linear Programming (ILP) model to find the optimal test cost. The ILP model is implemented on several designs constructed from ITC’02 benchmarks. The experimental results show significant reduction in test cost compared to when using schemes, which are optimized for non-stacked chips

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

Configurable 3D-integrated focal-plane sensor-processor array architecture

A mixed-signal Cellular Visual Microprocessor architecture with digital processors is described. An ASIC implementation is also demonstrated. The architecture is composed of a regular sensor readout circuit array, prepared for 3D face-to-face type integration, and one or several cascaded array of mainly identical (SIMD) processing elements. The individual array elements derived from the same general HDL description and could be of different in size, aspect ratio, and computing resources