Design and analysis of SRAMs for energy harvesting systems

PhD ThesisAt present, the battery is employed as a power source for wide varieties of microelectronic systems ranging from biomedical implants and sensor net-works to portable devices. However, the battery has several limitations and incurs many challenges for the majority of these systems. For instance, the design considerations of implantable devices concern about the battery from two aspects, the toxic materials it contains and its lifetime since replacing the battery means a surgical operation. Another challenge appears in wire-less sensor networks, where hundreds or thousands of nodes are scattered around the monitored environment and the battery of each node should be maintained and replaced regularly, nonetheless, the batteries in these nodes do not all run out at the same time. Since the introduction of portable systems, the area of low power designs has witnessed extensive research, driven by the industrial needs, towards the aim of extending the lives of batteries. Coincidentally, the continuing innovations in the field of micro-generators made their outputs in the same range of several portable applications. This overlap creates a clear oppor-tunity to develop new generations of electronic systems that can be powered, or at least augmented, by energy harvesters. Such self-powered systems benefit applications where maintaining and replacing batteries are impossi-ble, inconvenient, costly, or hazardous, in addition to decreasing the adverse effects the battery has on the environment. The main goal of this research study is to investigate energy harvesting aware design techniques for computational logic in order to enable the capa- II bility of working under non-deterministic energy sources. As a case study, the research concentrates on a vital part of all computational loads, SRAM, which occupies more than 90% of the chip area according to the ITRS re-ports. Essentially, this research conducted experiments to find out the design met-ric of an SRAM that is the most vulnerable to unpredictable energy sources, which has been confirmed to be the timing. Accordingly, the study proposed a truly self-timed SRAM that is realized based on complete handshaking protocols in the 6T bit-cell regulated by a fully Speed Independent (SI) tim-ing circuitry. The study proved the functionality of the proposed design in real silicon. Finally, the project enhanced other performance metrics of the self-timed SRAM concentrating on the bit-line length and the minimum operational voltage by employing several additional design techniques.Umm Al-Qura University, the Ministry of Higher Education in the Kingdom of Saudi Arabia, and the Saudi Cultural Burea

Design, analysis and implementation of voltage sensor for power-constrained systems

PhD ThesisThanks to an extensive effort by the global research community, the electronic technology has significantly matured over the last decade. This technology has enabled certain operations which humans could not otherwise easily perform. For instance, electronic systems can be used to perform sensing, monitoring and even control operations in environments such as outer space, underground, under the sea or even inside the human body. The main difficulty for electronics operating in these environments is access to a reliable and permanent source of energy. Using batteries as the immediate solution for this problem has helped to provide energy for limited periods of time; however, regular maintenance and replacement are required. Consequently, battery solutions fail wherever replacing them is not possible or operation for long periods is needed. For such cases, researchers have proposed harvesting ambient energy and converting it into an electrical form. An important issue with energy harvesters is that their operation and output power depend critically on the amount of energy they receive and because ambient energy often tends to be sporadic in nature, energy harvesters cannot produce stable or fixed levels of power all of the time. Therefore, electronic devices powered in this way must be capable of adapting their operation to the energy status of the harvester. To achieve this, information on the energy available for use is needed. This can be provided by a sensor capable of measuring voltage. However, stable and fixed voltage and time references are a prerequisite of most traditional voltage measurement devices, but these generally do not exist in energy harvesting environments. A further challenge is that such a sensor also needs to be powered by the energy harvester’s unstable voltage. In this thesis, the design of a reference-free voltage sensor, which can operate with a varying voltage source, is provided based on the capture of a portion of the total energy which is directly related to II the energy being sensed. This energy is then used to power a computation which quantifies captured energy over time, with the information directly generated as digital code. The sensor was fabricated in the 180 nm technology node and successfully tested by performing voltage measurements over the range 1.8 V to 0.8 V

Power delivery mechanisms for asynchronous loads in energy harvesting systems

PhD ThesisFor systems depending on methods, a fundamental contradiction in the power delivery chain has existed between conventional to supply it. DC/DC conversion (e.g.) has therefore been an integral part of such systems to resolve this contradiction. be made tolerant to a much wider range of Vdd variance. This may open up opportunities for much more energy efficient methods of power delivery. performance of different power delivery mechanisms driving both asynchronous and synchronous loads directly from a harvester source bypassing bulky energy method, which employs a energy from a EH circuit depending on load and source conditions, is developed. through comprehensive comparative analysis. Based on the novel CBB power delivery method, an asynchronous controller is circuits to work with tasks. The successful asynchronous control design drives a case study that is meant to explore relations between power path and task path. To deal with different tasks with variable harvested power, systems may have a range of operation conditions and thus dynamically call for CBB or SCC type power set of capacitors to form CBB or SCC is implemented with economic system size. This work presents an unconventional way of designing a compact-size, quick- circuit overcome large voltage variation in EH systems and implement smart power management for harsh EH environment. The power delivery mechanisms (SCC, employed to help asynchronous- logic-based chip testing and micro-scale EH system demonstrations

Energy harvesting technologies for structural health monitoring of airplane components - a review

With the aim of increasing the efficiency of maintenance and fuel usage in airplanes, structural health monitoring (SHM) of critical composite structures is increasingly expected and required. The optimized usage of this concept is subject of intensive work in the framework of the EU COST Action CA18203 "Optimising Design for Inspection" (ODIN). In this context, a thorough review of a broad range of energy harvesting (EH) technologies to be potentially used as power sources for the acoustic emission and guided wave propagation sensors of the considered SHM systems, as well as for the respective data elaboration and wireless communication modules, is provided in this work. EH devices based on the usage of kinetic energy, thermal gradients, solar radiation, airflow, and other viable energy sources, proposed so far in the literature, are thus described with a critical review of the respective specific power levels, of their potential placement on airplanes, as well as the consequently necessary power management architectures. The guidelines provided for the selection of the most appropriate EH and power management technologies create the preconditions to develop a new class of autonomous sensor nodes for the in-process, non-destructive SHM of airplane components.The work of S. Zelenika, P. Gljušcic, E. Kamenar and Ž. Vrcan is partly enabled by using the equipment funded via the EU European Regional Development Fund (ERDF) project no. RC.2.2.06-0001: “Research Infrastructure for Campus-based Laboratories at the University of Rijeka (RISK)” and partly supported by the University of Rijeka, Croatia, project uniri-tehnic-18-32 „Advanced mechatronics devices for smart technological solutions“. Z. Hadas, P. Tofel and O. Ševecek acknowledge the support provided via the Czech Science Foundation project GA19-17457S „Manufacturing and analysis of flexible piezoelectric layers for smart engineering”. J. Hlinka, F. Ksica and O. Rubes gratefully acknowledge the financial support provided by the ESIF, EU Operational Programme Research, Development and Education within the research project Center of Advanced Aerospace Technology (Reg. No.: CZ.02.1.01/0.0/0.0/16_019/0000826) at the Faculty of Mechanical Engineering, Brno University of Technology. V. Pakrashi would like to acknowledge UCD Energy Institute, Marine and Renewable Energy Ireland (MaREI) centre Ireland, Strengthening Infrastructure Risk Assessment in the Atlantic Area (SIRMA) Grant No. EAPA\826/2018, EU INTERREG Atlantic Area and Aquaculture Operations with Reliable Flexible Shielding Technologies for Prevention of Infestation in Offshore and Coastal Areas (FLEXAQUA), MarTera Era-Net cofund PBA/BIO/18/02 projects. The work of J.P.B. Silva is partially supported by the Portuguese Foundation for Science and Technology (FCT) in the framework of the Strategic Funding UIDB/FIS/04650/2020. M. Mrlik gratefully acknowledges the support of the Ministry of Education, Youth and Sports of the Czech Republic-DKRVO (RP/CPS/2020/003

The Convergence of Parametric Resonance and Vibration Energy Harvesting

Energy harvesting is an emerging technology that derives electricity from the ambient environment in a decentralised and self-contained fashion. Applications include self-powered medical implants, wearable electronics and wireless sensors for structural health monitoring. Amongst the vast options of ambient sources, vibration energy harvesting (VEH) has attracted by far the most research attention. Two of the key persisting issues of VEH are the limited power density compared to conventional power supplies and confined operational frequency bandwidth in light of the random, broadband and fast-varying nature of real vibration. The convention has relied on directly excited resonance to maximise the mechanical-to-electrical energy conversion efficiency. This thesis takes a fundamentally different approach by employing parametric resonance, which, unlike the former, its resonant amplitude growth does not saturate due to linear damping. Therefore, parametric resonance, when activated, has the potential to accumulate much more energy than direct resonance. The vibrational nonlinearities that are almost always associated with parametric resonance can offer a modest frequency widening. Despite its promising theoretical potentials, there is an intrinsic damping dependent initiation threshold amplitude, which must be attained prior to its onset. The relatively low amplitude of real vibration and the unavoidable presence of electrical damping to extract the energy render the onset of parametric resonance practically elusive. Design approaches have been devised to passively minimise this initiation threshold. Simulation and experimental results of various design iterations have demonstrated favourable results for parametric resonance as well as the various threshold-reduction mechanisms. For instance, one of the macro-scale electromagnetic prototypes (∼1800 cm3) when parametrically driven, has demonstrated around 50% increase in half power band and an order of magnitude higher peak power (171.5 mW at 0.57 ms−2) in contrast to the same prototype directly driven at fundamental resonance (27.75 mW at 0.65 ms−2). A MEMS (micro-electromechanical system) prototype with the additional threshold-reduction design needed 1 ms−2 excitation to activate parametric resonance while a comparable device without the threshold-reduction mechanism required in excess of 30 ms−2. One of the macro-scale piezoelectric prototypes operated into auto-parametric resonance has demon-strated notable further reduction to the initiation threshold. A vacuum packaged MEMS prototype demonstrated broadening of the frequency bandwidth along with higher power peak (324 nW and 160 Hz) for the parametric regime compared to when operated in room pressure (166 nW and 80 Hz), unlike the higher but narrower direct resonant peak (60.9 nW and 11 Hz in vacuum and 20.8 nW and 40 Hz in room pressure). The simultaneous incorporation of direct resonance and bi-stability have been investigated to realise multi-regime VEH. The potential to integrate parametric resonance in the electrical domains have also been numerically explored. The ultimate aim is not to replace direct resonance but rather for the various resonant phenomena to complement each other and together harness a larger region of the available power spectrum

Design and Analysis of a Mechanical Driveline with Generator for an Atmospheric Energy Harvester

The advent of renewable energy as a primary power source for microelectronic devices has motivated research within the energy harvesting community over the past decade. Compact, self-contained, portable energy harvesters can be applied to wireless sensor networks, Internet of Things (IoT) smart appliances, and a multitude of standalone equipment; replacing batteries and improving the operational life of such systems. Atmospheric changes influenced by cyclical temporal variations offer an abundance of harvestable thermal energy. However, the low conversion efficiency of a common thermoelectric device does not tend to be practical for microcircuit operations. One solution may lie in a novel electromechanical power transformer integrated with a thermodynamic based phase change material to create a temperature/pressure energy harvester. The performance of the proposed harvester will be investigated using both numerical and experimental techniques to offer insight into its functionality and power generation capabilities. The atmospheric energy harvester consists of a ethyl chloride filled mechanical bellows attached to an end plate and constrained by a stiff spring and four guide rails that allow translational motion. The electromechanical power transformer consists of a compound gear train driven by the bellows end plate, a ratchet-controlled coil spring to store energy, and a DC micro generator. Nonlinear mathematical models have been developed for this multi-domain dynamic system using fundamental engineering principles. The initial analyses predicted 9.6 mW electric power generation over a 24 hour period for ±1°C temperature variations about a nominal 22°C temperature. Transfer functions were identified from the lumped parameter models and the transient behavior of the coupled thermal-electromechanical system has been studied. A prototype experimental system was fabricated and laboratory tested to study the overall performance and validate the mathematical models for the integrated energy harvester system. The experimental results agree with the numerical analyses in behavioral characteristics. Further, the power generation capacity of 30 mW for a representative electrical resistance load and emulated rack input which correspond to 50 cyclic bidirectional temperature variations (~175 hours of field operation) validated the simulation models. This research study provides insight into the challenges of designing an electromechanical power transformer to complement an atmospheric energy harvester system. The mathematical models estimated the behavior and performance of the integrated harvester system and establishes a foundation for future optimization studies. The opportunity to power microelectronic devices in the milliwatt range for burst electric operation or with the use of supercapacitors/batteries enables global remote operation of smart appliances. This system can assist in reducing/eliminating the need for batteries and improving the operational life of a variety of autonomous equipment. Future research areas have been identified to improve the overall system capabilities and implement the harvester device for real-world applications

Piezoelectric Energy Harvesting: Enhancing Power Output by Device Optimisation and Circuit Techniques

Energy harvesting; that is, harvesting small amounts of energy from environmental sources such as solar, air flow or vibrations using small-scale (≈1cm 3 ) devices, offers the prospect of powering portable electronic devices such as GPS receivers and mobile phones, and sensing devices used in remote applications: wireless sensor nodes, without the use of batteries. Numerous studies have shown that power densities of energy harvesting devices can be hundreds of µW; however the literature also reveals that power requirements of many electronic devices are in the mW range. Therefore, a key challenge for the successful deployment of energy harvesting technology remains, in many cases, the provision of adequate power. This thesis aims to address this challenge by investigating two methods of enhancing the power output of a piezoelectric-based vibration energy harvesting device. Cont/d

A gravitational torque energy harvesting system for rotational motion

This thesis describes a novel, single point-of-attachment, gravitational torque energy harvesting system powered from rotational motion. The primary aim of such a system is to scavenge energy from a continuously rotating host in order to power a wireless sensor node. In this thesis, a wireless tachometer was prototyped. Most published work on motion-driven energy harvesters has used ambient vibrations in the environment as the energy source. However, none of the reported devices have been designed to harvest energy directly from continuous ambient rotation. There are important applications such as tire pressure sensing and condition monitoring of machinery where the host structure experiences continuous rotation. In this work, it is shown that in many applications, a rotational energy harvester can offer significant improvements in power density over its vibration-driven counterparts. A prototype single point-of-attachment rotational energy harvester was conceived using a simple direct-current generator. The rotational source was coupled to the stator and an offset mass was anchored on the rotor to create a counteractive gravitational torque. This produces a relative angular speed between rotor and stator which causes power to be generated. Power transfer from the generator to a load was maximised by enforcing an input impedance match between the generator’s armature resistance and the input impedance of a boost converter which in this case, functioned as a resistance emulator. Energy storage and output voltage regulation were implemented using supercapacitors and a wide-input buck regulator respectively. When excess power was generated, it was stored in the supercapacitors and during low source rotation speeds, i.e. insufficient harvested power, the supercapacitors will discharge to maintain operation of the interface electronics. A detailed optimisation procedure of a boost converter was conducted in Matlab in order to minimise the power loss, resulting in a maximum voltage gain of 11.1 and measured circuit efficiency of 96 %. A state-space control model of the harvester electronics was developed in the analogue domain using classical control techniques and this showed the system to be closed-loop stable. A final prototype of the rotational energy harvesting system was built and this comprised an input impedance controller, wireless transmitter and tachometer. The entire system has a measured end-to-end efficiency which peaked at 58 % from a source rotation of 1400 RPM with the generator producing 1.45 W under matched load conditions

SUSTAINABLE ENERGY HARVESTING TECHNOLOGIES – PAST, PRESENT AND FUTURE

Chapter 8: Energy Harvesting Technologies: Thick-Film Piezoelectric Microgenerato

Chaotification as a Means of Broadband Vibration Energy Harvesting with Piezoelectric Materials

Computing advances and component miniaturization in circuits coupled with stagnating battery technology have fueled growth in the development of high efficiency energy harvesters. Vibration-to-electricity energy harvesting techniques have been investigated extensively for use in sensors embedded in structures or in hard-to-reach locations like turbomachinery, surgical implants, and GPS animal trackers. Piezoelectric materials are commonly used in harvesters as they possess the ability to convert strain energy directly into electrical energy and can work concurrently as actuators for damping applications. The prototypical harvesting system places two piezoelectric patches on both sides of the location of maximum strain on a cantilever beam. While efficient around resonance, performance drops dramatically should the driving frequency drift away from the beam\u27s fundamental frequency. To date, researchers have worked to improve harvesting capability by modifying material properties, using alternative geometries, creating more efficient harvesting circuits, and inducing nonlinearities. These techniques have partially mitigated the resonance excitation dependence for vibration-based harvesting, but much work remains. In this dissertation, an induced nonlinearity destabilizes a central equilibrium point, resulting in a bistable potential function governing the cantilever beam system. Depending on the environment, multiple stable solutions are possible and can coexist. Typically, researchers neglect chaos and assume that with enough energy in the ambient environment, large displacement trajectories can exist uniquely. When subjected to disturbances a system can fall to coexistent lower energy solutions including aperiodic, chaotic oscillations. Treating chaotic motion as a desirable behavior of the system allows frequency content away from resonance to produce motion about a theoretically infinite number of unstable periodic orbits that can be stabilized through control. The extreme sensitivity to initial conditions exhibited by chaotic systems paired with a pole placement control strategy pioneered by Ott, Grebogi, and Yorke permits small perturbations to an accessible system parameter to alter the system response dramatically. Periodic perturbation of the system trajectories in the vicinity of isolated unstable orbit points can therefore stabilize low-energy chaotic oscillations onto larger trajectory orbits more suitable for energy harvesting. The periodic perturbation-based control method rids the need of a system model. It only requires discrete displacement, velocity, or voltage time series data of the chaotic system driven by harmonic excitation. While the analysis techniques are not fundamentally limited to harmonic excitation, this condition permits the use of standard discrete mapping techniques to isolate periodic orbits of interest. Local linear model fits characterize the orbit and admit the necessary control perturbation calculations from the time series data. This work discusses the feasibility of such a method for vibration energy harvesting, displays stable solutions under various control algorithms, and implements a hybrid bench-top experiment using MATLAB and LabVIEW FPGA. In conclusion, this work discusses the limitations for wide-scale use and addresses areas of further work; both with respect to chaotic energy harvesting and parallel advances required within the field as a whole