1,482 research outputs found
Wireless industrial monitoring and control networks: the journey so far and the road ahead
While traditional wired communication technologies have played a crucial role in industrial monitoring and control networks over the past few decades, they are increasingly proving to be inadequate to meet the highly dynamic and stringent demands of today’s industrial applications, primarily due to the very rigid nature of wired infrastructures. Wireless technology, however, through its increased pervasiveness, has the potential to revolutionize the industry, not only by mitigating the problems faced by wired solutions, but also by introducing a completely new class of applications. While present day wireless technologies made some preliminary inroads in the monitoring domain, they still have severe limitations especially when real-time, reliable distributed control operations are concerned. This article provides the reader with an overview of existing wireless technologies commonly used in the monitoring and control industry. It highlights the pros and cons of each technology and assesses the degree to which each technology is able to meet the stringent demands of industrial monitoring and control networks. Additionally, it summarizes mechanisms proposed by academia, especially serving critical applications by addressing the real-time and reliability requirements of industrial process automation. The article also describes certain key research problems from the physical layer communication for sensor networks and the wireless networking perspective that have yet to be addressed to allow the successful use of wireless technologies in industrial monitoring and control networks
Hybrid Satellite-Terrestrial Communication Networks for the Maritime Internet of Things: Key Technologies, Opportunities, and Challenges
With the rapid development of marine activities, there has been an increasing
number of maritime mobile terminals, as well as a growing demand for high-speed
and ultra-reliable maritime communications to keep them connected.
Traditionally, the maritime Internet of Things (IoT) is enabled by maritime
satellites. However, satellites are seriously restricted by their high latency
and relatively low data rate. As an alternative, shore & island-based base
stations (BSs) can be built to extend the coverage of terrestrial networks
using fourth-generation (4G), fifth-generation (5G), and beyond 5G services.
Unmanned aerial vehicles can also be exploited to serve as aerial maritime BSs.
Despite of all these approaches, there are still open issues for an efficient
maritime communication network (MCN). For example, due to the complicated
electromagnetic propagation environment, the limited geometrically available BS
sites, and rigorous service demands from mission-critical applications,
conventional communication and networking theories and methods should be
tailored for maritime scenarios. Towards this end, we provide a survey on the
demand for maritime communications, the state-of-the-art MCNs, and key
technologies for enhancing transmission efficiency, extending network coverage,
and provisioning maritime-specific services. Future challenges in developing an
environment-aware, service-driven, and integrated satellite-air-ground MCN to
be smart enough to utilize external auxiliary information, e.g., sea state and
atmosphere conditions, are also discussed
Scaling Laws for Infrastructure Single and Multihop Wireless Networks in Wideband Regimes
With millimeter wave bands emerging as a strong candidate for 5G cellular
networks, next-generation systems may be in a unique position where spectrum is
plentiful. To assess the potential value of this spectrum, this paper derives
scaling laws on the per mobile downlink feasible rate with large bandwidth and
number of nodes, for both Infrastructure Single Hop (ISH) and Infrastructure
Multi-Hop (IMH) architectures. It is shown that, for both cases, there exist
\emph{critical bandwidth scalings} above which increasing the bandwidth no
longer increases the feasible rate per node. These critical thresholds coincide
exactly with the bandwidths where, for each architecture, the network
transitions from being degrees-of-freedom-limited to power-limited. For ISH,
this critical bandwidth threshold is lower than IMH when the number of users
per base station grows with network size. This result suggests that multi-hop
transmissions may be necessary to fully exploit large bandwidth degrees of
freedom in deployments with growing number of users per cell.Comment: 5 pages, 3 figure
Data Collection in Two-Tier IoT Networks with Radio Frequency (RF) Energy Harvesting Devices and Tags
The Internet of things (IoT) is expected to connect physical objects and end-users using technologies such as wireless sensor networks and radio frequency identification (RFID). In addition, it will employ a wireless multi-hop backhaul to transfer data collected by a myriad of devices to users or applications such as digital twins operating in a Metaverse. A critical issue is that the number of packets collected and transferred to the Internet is bounded by limited network resources such as bandwidth and energy. In this respect, IoT networks have adopted technologies such as time division multiple access (TDMA), signal interference cancellation (SIC) and multiple-input multiple-output (MIMO) in order to increase network capacity. Another fundamental issue is energy. To this end, researchers have exploited radio frequency (RF) energy-harvesting technologies to prolong the lifetime of energy constrained sensors and smart devices. Specifically, devices with RF energy harvesting capabilities can rely on ambient RF sources such as access points, television towers, and base stations. Further, an operator may deploy dedicated power beacons that serve as RF-energy sources. Apart from that, in order to reduce energy consumption, devices can adopt ambient backscattering communication technologies. Advantageously, backscattering allows devices to communicate using negligible amount of energy by modulating ambient RF signals.
To address the aforementioned issues, this thesis first considers data collection in a two-tier MIMO ambient RF energy-harvesting network. The first tier consists of routers with MIMO capability and a set of source-destination pairs/flows. The second tier consists of energy harvesting devices that rely on RF transmissions from routers for energy supply. The problem is to determine a minimum-length TDMA link schedule that satisfies the traffic demand of source-destination pairs and energy demand of energy harvesting devices. It formulates the problem as a linear program (LP), and outlines a heuristic to construct transmission sets that are then used by the said LP. In addition, it outlines a new routing metric that considers the energy demand of energy harvesting devices to cope with routing requirements of IoT networks. The simulation results show that the proposed algorithm on average achieves 31.25% shorter schedules as compared to competing schemes. In addition, the said routing metric results in link schedules that are at most 24.75% longer than those computed by the LP
- …