778 research outputs found

    Design of Power Receiving Units for 6.78MHz Wireless Power Transfer Systems

    Get PDF
    In the last decade, the wireless power transfer (WPT) technology has been a popular topic in power electronics research and increasingly adopted by consumers. The AirFuel WPT standard utilizes resonant coils to transfer energy at 6.78 MHz, introducing many benefits such as longer charging distance, multi-device charging, and high tolerance of the coil misalignment. However, variations in coil coupling due to the change in receiving coil positions alter the equivalent load reactance, degrading efficiency. In recent studies, active full-bridge rectifiers are employed on WPT receivers because of their superior efficiency, controllability, and ability to compensate for detuned WPT networks. In order to take advantage of those characteristics, the rectifier switching actions must be synchronized with the magnetic field. In the literature, existing solutions for synchronizing the active rectifier in WPT systems are mostly not reliable and bulky, which is not suitable for small receivers. Therefore, a frequency synchronous rectifier with compact on-board control is proposed in this thesis. The rectifier power stage is designed to deliver 40 W to the load while achieving full zero-voltage switching to minimize the loss. The inherent feedback from the power stage dynamics to the sensed signal is analyzed to design stable and robust synchronization control, even at a low power of 0.02 W. The control system is accomplished using commercial components, including a low-cost microcontroller, which eliminates the need for bulky control and external sensing hardware. This high power density design allows the receiver to be integrated into daily consumer electronics such as laptops and monitors. Finally, a wide-range and high v resolution control scheme of the rectifier input phase is proposed to enable the dynamic impedance matching capability, maintaining high system efficiency over wide loading conditions. In addition, to increase the WPT technology adoption to low-power consumer electronics, a small wireless receiver replacing conventional AA batteries is developed. This receiver can supply power to existing AA battery-powered devices while providing the benefit of WPT technologies to consumers

    Reversible DC-DC converter for a dual voltage automative system using zero voltage switching techniques

    Get PDF
    Abstract: A novel hysteretic controller for a bi-directional dc-dc converter with ZVS and interleaving for dual voltage systems in automobiles is presented. A variable frequency extended band hysteretic current control method is proposed. In comparison with classical fixed frequency current control PWM, the reverse polarity peak current needed for ZVS operation is kept constant. Inductor current ripple decreases with load reduction. Automatic changes in operation between buck and boost modes are accomplished without transient currents. Converter simulations are carried out using Matlab/Simulink platform

    Electronic operation and control of high-intensity gas-discharge lamps

    Get PDF
    The ever increasing amount of global energy consumption based on the application of fossil fuels is threatening the earth’s natural resources and environment. Worldwide, grid-based electric lighting consumes 19 % of total global electricity production. For this reason the transition towards energy efficient lighting plays an important environmental role. One of the key technologies in this transition is High-Intensity Discharge (HID) lighting. The technical revolution in gas-discharge lamps has resulted in the highlyefficient lamps that are available nowadays. As with most energy efficient light solutions, all HID lighting systems require a ballast to operate. Traditionally, magnetic ballast designs were the only choice available for HID lighting systems. Today, electronic lampdrivers can offer additional power saving, flicker free operation, and miniaturisation. Electronic lamp operation enables additional degrees of freedom in lamp-current control over the conventional electro-magnetic (EM) ballasts. The lamp-driver system performance depends on both the dynamics of the lamp and the driver. This thesis focuses on the optimisation of electronically operated HID systems, in terms of highly-efficient lamp-driver topologies and, more specifically, lamp-driver interaction control. First, highly-efficient power topologies to operate compact HID lamps on low-frequency-square-wave (LFSW) current are explored. The proposed two-stage electronic lamp-driver consists of a Power Factor Corrector (PFC) stage that meets the power utility standards. This converter is coupled to a stacked buck converter that controls the lamp-current. Both stages are operated in Zero Voltage Switching (ZVS) mode in order to reduce the switching losses. The resulting two-stage lamp-drivers feature flexible controllability, high efficiency, and high power density, and are suitable for power sandwich packaging. Secondly, lamp-driver interaction (LDI) has been studied in the simulation domain and control algorithms have been explored that improve the stability, and enable system optimisation. Two HID lamp models were developed. The first model describes the HID lamp’s small-signal electrical behaviour and its purpose is to aid to study the interaction stability. The second HID lamp model has been developed based on physics equations for the arc column and the electrode behaviour, and is intended for lampdriver simulations and control applications. Verification measurements have shown that the lamp terminal characteristics are present over a wide power and frequency range. Three LDI control algorithms were explored, using the proposed lampmodels. The first control principle optimises the LDI for a broad range of HID lamps operated at normal or reduced power. This approach consists of two control loops integrated into a fuzzy-logic controller that stabilises the lamp-current and optimises the commutation process. The second control problem concerns the application of ultra high performance (UHP) HID lamps in projection applications that typically set stringent requirements on the quality of the light generated by these lamps, and therefore the lampcurrent. These systems are subject to periodic disturbances synchronous with the LFSW commutation period. Iterative learning control (ILC) has been examined. It was experimentally verified that this algorithm compensates for repetitive disturbances. Third, Electronic HID operation also opens the door for continuous HID lamp dimming that can provide additional savings. To enable stable dimming, an observer-based HID lamp controller has been developed. This controller sets a stable minimum dim-level and monitors the gas-discharge throughout lamp life. The HID lamp observer derives physical lamp state signals from the HID arc discharge physics and the related photometric properties. Finally, practical measurements proved the proposed HID lamp observer-based control principle works satisfactorily

    System identification and adaptive current balancing ON/OFF control of DC-DC switch mode power converter

    Get PDF
    PhD ThesisReliability becomes more and more important in industrial application of Switch Mode Power Converters (SMPCs). A poorly performing power supply in a power system can influence its operation and potentially compromise the entire system performance in terms of efficiency. To maintain a high reliability, high performance SMPC effective control is necessary for regulating the output of the SMPC system. However, an uncertainty is a key factor in SMPC operation. For example, parameter variations can be caused by environmental effects such as temperature, pressure and humidity. Usually, fixed controllers cannot respond optimally and generate an effective signal to compensate the output error caused by time varying parameter changes. Therefore, the stability is potentially compromised in this case. To resolve this problem, increasing interest has been shown in employing online system identification techniques to estimate the parameter values in real time. Moreover, the control scheme applied after system identification is often called “adaptive control” due to the control signal selfadapting to the parameter variation by receiving the information from the system identification process. In system identification, the Recursive Least Square (RLS) algorithm has been widely used because it is well understood and easy to implement. However, despite the popularity of RLS, the high computational cost and slow convergence speed are the main restrictions for use in SMPC applications. For this reason, this research presents an alternative algorithm to RLS; Fast Affline Projection (FAP). Detailed mathematical analysis proves the superior computational efficiency of this algorithm. Moreover, simulation and experiment result verify this unique adaptive algorithm has improved performance in terms of computational cost and convergence speed compared with the conventional RLS methods. Finally, a novel adaptive control scheme is designed for optimal control of a DC-DC buck converter during transient periods. By applying the proposed adaptive algorithm, the control signal can be successfully employed to change the ON/OFF state of the power transistor in the DC-DC buck converter to improve the dynamic behaviour. Simulation and experiment result show the proposed adaptive control scheme significantly improves the transient response of the buck converter, particularly during an abrupt load change conditio

    Power Electronic Converter Configuration and Control for DC Microgrid Systems

    Get PDF

    Applications of Power Electronics:Volume 2

    Get PDF

    A survey of differential flatness-based control applied to renewable energy sources

    Get PDF
    Conference ProceedingsThis paper presents an overview of various methods used to minimize the fluctuating impacts of power generated from renewable energy sources. Several sources are considered in the study (biomass, wind, solar, hydro and geothermal). Different control methods applied to their control are cited, alongside some previous applications. Hence, it further elaborates on the adoptive control principles, of which includes; Load ballast control, dummy load control, proportional integral and derivative (PID) control, proportional integral (PI) control, pulse-width modulation (PWM) control, buck converter control, boost converter control, pitch angle control, valve control, the rate of river flow at turbine, bidirectional diffuser-augmented control and differential flatnessbased controller. These control operations in renewable energy power generation are mainly based on a steady-state linear control approach. However, the flatness based control principle has the ability to resolve the complex control problem of renewable energy systems while exploiting their linear properties. Using their flatness properties, feedback control is easily achieved which allows for optimal/steady output of the system components. This review paper highlights the benefits that range from better control techniques for renewable energy systems to established robust grid (or standalone generations) connections that can bring immense benefits to their operation and maintenance costs
    • …
    corecore