Scalable trajectory methods for on-demand analog macromodel extraction.

ABSTRACT Trajectory methods sample the state trajectory of a circuit as it simulates in the time domain, and build macromodels by reducing and interpolating among the linearizations created at a suitably spaced subset of the time points visited during training simulations. Unfortunately, moving from simple to industrial circuits requires more extensive training, which creates models too large to interpolate efficiently. To make trajectory methods practical, we describe a scalable interpolation architecture, and the first implementation of a complete trajectory "infrastructure" inside a full SPICE engine. The approach supports arbitrarily large training runs, automatically prunes redundant trajectory samples, supports limited hierarchy, enables incremental macromodel updates, and gives 3-10X speedups for larger circuits

Empirical derivation of upper and lower bounds of NBTI aging for embedded cores

In deeply scaled CMOS technologies, device aging causes transistor performance parameters to degrade over time. While reliable models to accurately assess these degradations are available for devices and circuits, the extension to these models for estimating the aging of microprocessor cores is not trivial and there is no well accepted model in the literature. This work proposes a methodology for deriving an NBTI-induced aging model for embedded cores. Since aging can only be determined on a netlist, we use an empirical approach based on characterizing the model using a set of open synthesizable embedded cores, which allows us to establish a link between the aging at the transistor level and the aging from the core perspective in terms of maximum frequency degradation. Using this approach, we were able to (1) prove the independence of the aging on the workloads which run by the cores, and (2) calculate upper and lower bounds for the “aging factor” that can be used for a generic embedded processor. Results show that our method yields very good accuracy in predicting the frequency degradation of cores due to NBTI aging effect, and can be used with confidence when the netlist of the cores is not available

Efficient FPGA implementation and power modelling of image and signal processing IP cores

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Field Programmable Gate Arrays (FPGAs) are the technology of choice in a number ofimage and signal processing application areas such as consumer electronics, instrumentation, medical data processing and avionics due to their reasonable energy consumption, high performance, security, low design-turnaround time and reconfigurability. Low power FPGA devices are also emerging as competitive solutions for mobile and thermally constrained platforms. Most computationally intensive image and signal processing algorithms also consume a lot of power leading to a number of issues including reduced mobility, reliability concerns and increased design cost among others. Power dissipation has become one of the most important challenges, particularly for FPGAs. Addressing this problem requires optimisation and awareness at all levels in the design flow. The key achievements of the work presented in this thesis are summarised here. Behavioural level optimisation strategies have been used for implementing matrix product and inner product through the use of mathematical techniques such as Distributed Arithmetic (DA) and its variations including offset binary coding, sparse factorisation and novel vector level transformations. Applications to test the impact of these algorithmic and arithmetic transformations include the fast Hadamard/Walsh transforms and Gaussian mixture models. Complete design space exploration has been performed on these cores, and where appropriate, they have been shown to clearly outperform comparable existing implementations. At the architectural level, strategies such as parallelism, pipelining and systolisation have been successfully applied for the design and optimisation of a number of cores including colour space conversion, finite Radon transform, finite ridgelet transform and circular convolution. A pioneering study into the influence of supply voltage scaling for FPGA based designs, used in conjunction with performance enhancing strategies such as parallelism and pipelining has been performed. Initial results are very promising and indicated significant potential for future research in this area. A key contribution of this work includes the development of a novel high level power macromodelling technique for design space exploration and characterisation of custom IP cores for FPGAs, called Functional Level Power Analysis and Modelling (FLPAM). FLPAM is scalable, platform independent and compares favourably with existing approaches. A hybrid, top-down design flow paradigm integrating FLPAM with commercially available design tools for systematic optimisation of IP cores has also been developed

EARLY PERFORMANCE PREDICTION METHODOLOGY FOR MANY-CORES ON CHIP BASED APPLICATIONS

Modern high performance computing applications such as personal computing, gaming, numerical simulations require application-specific integrated circuits (ASICs) that comprises of many cores. Performance for these applications depends mainly on latency of interconnects which transfer data between cores that implement applications by distributing tasks. Time-to-market is a critical consideration while designing ASICs for these applications. Therefore, to reduce design cycle time, predicting system performance accurately at an early stage of design is essential. With process technology in nanometer era, physical phenomena such as crosstalk, reflection on the propagating signal have a direct impact on performance. Incorporating these effects provides a better performance estimate at an early stage. This work presents a methodology for better performance prediction at an early stage of design, achieved by mapping system specification to a circuit-level netlist description. At system-level, to simplify description and for efficient simulation, SystemVerilog descriptions are employed. For modeling system performance at this abstraction, queueing theory based bounded queue models are applied. At the circuit level, behavioral Input/Output Buffer Information Specification (IBIS) models can be used for analyzing effects of these physical phenomena on on-chip signal integrity and hence performance. For behavioral circuit-level performance simulation with IBIS models, a netlist must be described consisting of interacting cores and a communication link. Two new netlists, IBIS-ISS and IBIS-AMI-ISS are introduced for this purpose. The cores are represented by a macromodel automatically generated by a developed tool from IBIS models. The generated IBIS models are employed in the new netlists. Early performance prediction methodology maps a system specification to an instance of these netlists to provide a better performance estimate at an early stage of design. The methodology is scalable in nanometer process technology and can be reused in different designs

Efficient architectures and power modelling of multiresolution analysis algorithms on FPGA

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In the past two decades, there has been huge amount of interest in Multiresolution Analysis Algorithms (MAAs) and their applications. Processing some of their applications such as medical imaging are computationally intensive, power hungry and requires large amount of memory which cause a high demand for efficient algorithm implementation, low power architecture and acceleration. Recently, some MAAs such as Finite Ridgelet Transform (FRIT) Haar Wavelet Transform (HWT) are became very popular and they are suitable for a number of image processing applications such as detection of line singularities and contiguous edges, edge detection (useful for compression and feature detection), medical image denoising and segmentation. Efficient hardware implementation and acceleration of these algorithms particularly when addressing large problems are becoming very chal-lenging and consume lot of power which leads to a number of issues including mobility, reliability concerns. To overcome the computation problems, Field Programmable Gate Arrays (FPGAs) are the technology of choice for accelerating computationally intensive applications due to their high performance. Addressing the power issue requires optimi- sation and awareness at all level of abstractions in the design flow. The most important achievements of the work presented in this thesis are summarised here. Two factorisation methodologies for HWT which are called HWT Factorisation Method1 and (HWTFM1) and HWT Factorasation Method2 (HWTFM2) have been explored to increase number of zeros and reduce hardware resources. In addition, two novel efficient and optimised architectures for proposed methodologies based on Distributed Arithmetic (DA) principles have been proposed. The evaluation of the architectural results have shown that the proposed architectures results have reduced the arithmetics calculation (additions/subtractions) by 33% and 25% respectively compared to direct implementa-tion of HWT and outperformed existing results in place. The proposed HWTFM2 is implemented on advanced and low power FPGA devices using Handel-C language. The FPGAs implementation results have outperformed other existing results in terms of area and maximum frequency. In addition, a novel efficient architecture for Finite Radon Trans-form (FRAT) has also been proposed. The proposed architecture is integrated with the developed HWT architecture to build an optimised architecture for FRIT. Strategies such as parallelism and pipelining have been deployed at the architectural level for efficient im-plementation on different FPGA devices. The proposed FRIT architecture performance has been evaluated and the results outperformed some other existing architecture in place. Both FRAT and FRIT architectures have been implemented on FPGAs using Handel-C language. The evaluation of both architectures have shown that the obtained results out-performed existing results in place by almost 10% in terms of frequency and area. The proposed architectures are also applied on image data (256 £ 256) and their Peak Signal to Noise Ratio (PSNR) is evaluated for quality purposes. Two architectures for cyclic convolution based on systolic array using parallelism and pipelining which can be used as the main building block for the proposed FRIT architec-ture have been proposed. The first proposed architecture is a linear systolic array with pipelining process and the second architecture is a systolic array with parallel process. The second architecture reduces the number of registers by 42% compare to first architec-ture and both architectures outperformed other existing results in place. The proposed pipelined architecture has been implemented on different FPGA devices with vector size (N) 4,8,16,32 and word-length (W=8). The implementation results have shown a signifi-cant improvement and outperformed other existing results in place. Ultimately, an in-depth evaluation of a high level power macromodelling technique for design space exploration and characterisation of custom IP cores for FPGAs, called func-tional level power modelling approach have been presented. The mathematical techniques that form the basis of the proposed power modeling has been validated by a range of custom IP cores. The proposed power modelling is scalable, platform independent and compares favorably with existing approaches. A hybrid, top-down design flow paradigm integrating functional level power modelling with commercially available design tools for systematic optimisation of IP cores has also been developed. The in-depth evaluation of this tool enables us to observe the behavior of different custom IP cores in terms of power consumption and accuracy using different design methodologies and arithmetic techniques on virous FPGA platforms. Based on the results achieved, the proposed model accuracy is almost 99% true for all IP core's Dynamic Power (DP) components.Thomas Gerald Gray Charitable Trus

Hybrid Verification for Analog and Mixed-signal Circuits

With increasing design complexity and reliability requirements, analog and mixedsignal (AMS) verification manifests itself as a key bottleneck. While formal methods and machine learning have been proposed for AMS verification, these two types of techniques suffer from their own limitations, with the former being specifically limited by scalability and the latter by inherent errors in learning-based models. We present a new direction in AMS verification by proposing a hybrid formal/machinelearning- based verification technique (HFMV) to combine the best of the two worlds. HFMV builds formalism on the top of a machine learning model to verify AMS circuits efficiently while meeting a user-specified confidence level. Guided by formal checks, HFMV intelligently explores the high-dimensional parameter space of a given design by iteratively improving the machine learning model. As a result, it leads to accurate failure prediction in the case of a failing circuit or a reliable pass decision in the case of a good circuit. Our experimental results demonstrate that the proposed HFMV approach is capable of identifying hard-to-find failures which are completely missed by a huge number of random simulation samples while significantly cutting down training sample size and verification cycle time

AI/ML Algorithms and Applications in VLSI Design and Technology

An evident challenge ahead for the integrated circuit (IC) industry in the nanometer regime is the investigation and development of methods that can reduce the design complexity ensuing from growing process variations and curtail the turnaround time of chip manufacturing. Conventional methodologies employed for such tasks are largely manual; thus, time-consuming and resource-intensive. In contrast, the unique learning strategies of artificial intelligence (AI) provide numerous exciting automated approaches for handling complex and data-intensive tasks in very-large-scale integration (VLSI) design and testing. Employing AI and machine learning (ML) algorithms in VLSI design and manufacturing reduces the time and effort for understanding and processing the data within and across different abstraction levels via automated learning algorithms. It, in turn, improves the IC yield and reduces the manufacturing turnaround time. This paper thoroughly reviews the AI/ML automated approaches introduced in the past towards VLSI design and manufacturing. Moreover, we discuss the scope of AI/ML applications in the future at various abstraction levels to revolutionize the field of VLSI design, aiming for high-speed, highly intelligent, and efficient implementations

NONLINEAR OPERATORS FOR IMAGE PROCESSING: DESIGN, IMPLEMENTATION AND MODELING TECHNIQUES FOR POWER ESTIMATION

1998/1999Negli ultimi anni passati le applicazioni multimediali hanno visto uno sviluppo notevole, trovando applicazione in un gran numero di campi. Applicazioni come video conferenze, diagnostica medica, telefonia mobile e applicazioni militari necessitano il trattamento di una gran mole di dati ad alta velocità. Pertanto, l'elaborazione di immagini e di dati vocali è molto importante ed è stata oggetto di numerosi sforzi, nel tentativo di trovare algoritmi sempre più veloci ed efficaci. Tra gli algoritmi proposti, noi crediamo che gli operatori razionali svolgano un ruolo molto importante, grazie alla loro versatilità ed efficacia nell'elaborazione di dati. Negli ultimi anni sono stati proposti diversi algoritmi, dimostrando che questi operatori possono essere molto vantaggiosi in diverse applicazioni, producendo buoni risultati. Lo scopo di questo lavoro è di realizzare alcuni di questi algoritmi e, quindi, dimostrare che i filtri razionali, in particolare, possono essere realizzati senza ricorrere a sistemi di grandi dimensioni e possono raggiungere frequenze operative molto alte. Una volta che il blocco fondamentale di un sistema basato su operatori razionali sia stato realizzato, esso pu6 essere riusato con successo in molte altre applicazioni. Dal punto di vista del progettista, è importante avere uno schema generale di studio, che lo renda capace di studiare le varie configurazioni del sistema da realizzare e di analizzare i compromessi tra le variabili di progetto. In particolare, per soddisfare l'esigenza di metodi versatili per la stima della potenza, abbiamo sviluppato una tecnica di macro modellizazione che permette al progettista di stimare velocemente ed accuratamente la potenza dissipata da un circuito. La tesi è organizzata come segue: Nel Capitolo 1 alcuni sono presentati alcuni algoritmi studiati per la realizzazione. Ne viene data solo una veloce descrizione, lasciando comunque al lettore interessato dei riferimenti bibliografici. Nel Capitolo 2 vengono discusse le architetture fondamentali usate per la realizzazione. Principalmente sono state usate architetture a pipeline, ma viene data anche una descrizione degli approcci oggigiorno disponibili per l'ottimizzazione delle temporizzazioni. Nel Capitolo 3 sono presentate le realizzazioni di due sistemi studiati per questa tesi. Gli approcci seguiti si basano su ASIC e FPGA. Richiedono tecniche e soluzioni diverse per il progetto del sistema, per cui é interessante vedere cosa pu6 essere fatto nei due casi. Infine, nel Capitolo 4, descriviamo la nostra tecnica di macro modellizazione per la stima di potenza, dando una breve visione delle tecniche finora proposte e facendo vedere quali sono i vantaggi che il nostro metodo comporta per il progetto.In the past few years, multimedia application have been growing very fast, being applied to a large variety of fields. Applications like video conference, medical diagnostic, mobile phones, military applications require to handle large amount of data at high rate. Images as well as voice data processing are therefore very important and they have been subjected to a lot of efforts in order to find always faster and effective algorithms. Among image processing algorithms, we believe that rational operators assume an important role, due to their versatility and effectiveness in data processing. In the last years, several algorithms have been proposed, demonstrating that these operators can be very suitable in different applications with very good results. The aim of this work is to implement some of these algorithm and, therefore, demonstrate that rational filters, in particular, can be implemented without requiring large sized systems and they can operate at very high frequencies. Once the basic building block of a rational based system has been implemented, it can be successfully reused in many other applications. From the designer point of view, it is important to have a general framework, which makes it able to study various configurations of the system to be implemented and analyse the trade-off among the design variables. In particular, to meet the need far versatile tools far power estimation, we developed a new macro modelling technique, which allows the designer to estimate the power dissipated by a circuit quickly and accurately. The thesis is organized as follows: In chapter 1 we present some of the algorithms which have been studied for implementation. Only a brief overview is given, leaving to the interested reader some references in literature. In chapter 2 we discuss the basic architectures used for the implementations. Pipelined structures have been mainly used for this thesis, but an overview of the nowaday available approaches for timing optimization is presented. In chapter 3 we present two of the implementation designed for this thesis. The approaches followed are ASIC driven and FPGA drive. They require different techniques and different solution for the design of the system, therefore it is interesting to see what can be done in both the cases. Finally, in chapter 4, we describe our macro modelling techniques for power estimation, giving a brief overview of the up to now proposed techniques and showing the advantages our method brings to the design.XII Ciclo1969Versione digitalizzata della tesi di dottorato cartacea