Cooperative Control of the Dual Gantry-Tau Robot

Utilization of multiple parallel robots operating in the same work place and cooperating on the same job have opened up new challenges in coordination control strategies. Multiple robot control is a natural progression for Parallel Kinematic Machines (PKM) as it offers many of the desirable qualities especially in cooperative arrangements where multiple robots can be associated with an easily reconfigurable parallel machine. These special characteristics allow much faster and precise manipulations especially in manufacturing industries. With the possibility of cooperative control architecture, PKMs will be able to perform many of the tasks currently requiring dual serial robots such as complex assemblies, heavy load sharing and large machining jobs

Practical Model-based and Robust Control of Parallel Manipulators Using Passivity and Sliding Mode Theory

This chapter provides a practical strategy to realize accurate and robust control for 6 DOFs (degrees of freedom) parallel robots. The presented approach consists in two parts. The first basic part is based on the the compensation of the desired dynamics in combination with controller/observer for the single actuators. The passivity formalism offers an excellent framework to design and to tune the closed-loop dynamics, such that the desired behavior is obtained. The basic algorithm is proved to be locally robust towards uncertainties. The second part of the control strategy consists in a sliding mode controller. To keep the practical and computational efficient implementation, the proposed switching control considers explicitly only the friction model. Here we opt for the so called model-decomposition paradigm and we use additional integral action to improve robustness. The proposed approach is substantiated with experimental results demonstrating the effectiveness and success of the strategy that keeps control setup simple and intuitive. Keywords parallel manipulators, robust control, passivity formalism, sliding mode control, desired dynamics compensation, velocity observe

Aplicação de técnicas de controle preditivo em robô paralelo

This paper addresses the position tracking control application of a parallel robot using predictive control techniques. A Generalized Predictive Control strategy (GPC), which considers the linear dynamic model, is used to enhance the tracking position accuracy. The robustification of GPC against measurement noise and neglected dynamics using Youla parameterization is performed. A simulation of the orthoglide robot considering uncertainties related to geometrical and dynamic parameters, sensors noise and frictions is performed on two different trajectories. Finally, it is compared the ro-bustified GPC controller with the classical Computed Torque Control (CTC). The robustified GPC controller shows a better performance for high accelerations and it also reduces the effect of the noise in the control signal of the parallel robot.Este trabalho apresenta a aplicação de técnicas de controle preditivo para rastreamento de trajetórias de um robô paralelo. A estratégia de controle preditivo generalizado (GPC), que considera o modelo dinâmico linearizado, é usada para melhorar a precisão de rastreamento das trajetórias. O controlador preditivo generalizado é robustificado devido ao ruído de medição e dinâmicas não modeladas utilizando parametrização Youla. É realizada Uma simulação do robô Orthoglide considerando as incertezas dos parâmetros geométricos e dinâmicos, ruído nos sensores e atritos para duas trajetórias diferentes. Finalmente, o controlador GPC robus-tificado e a técnica de Controle de Torque Computado (CTC) são comparadas. Os resultados das simulações mostram que o controlador GPC robustificado apresenta um melhor desempenho para altas acelerações e também reduz o efeito do ruído no sinal de controle do robô paralelo.530540Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP

Dynamic Control of Soft Robotic Arm: An Experimental Study

In this paper, a reinforced soft robot prototype with a custom-designed actuator-space string encoder are created to investigate dynamic soft robotic trajectory tracking. The soft robot prototype embedded with the proposed adaptive passivity control and efficient dynamic model make the challenging trajectory tracking tasks possible. We focus on the exploration of tracking accuracy as well as the full potential of the proposed control strategy by performing experimental validations at different operation scenarios: various tracking speed and external disturbance. In all experimental scenarios, the proposed adaptive passivity control outperforms the conventional PD feedback linearization control. The experimental analysis details the advantage and shortcoming of the proposed approach, and points out the next steps for future soft robot dynamic control.Comment: 7 pages, 12 figure

Controller-observer design and dynamic parameter identification for model-based control of an electromechanical lower-limb rehabilitation system

[EN] Rehabilitation is a hazardous task for a mechanical system, since the device has to interact with the human extremities without the hands-on experience the physiotherapist acquires over time. A gap needs to be filled in terms of designing effective controllers for this type of devices. In this respect, the paper describes the design of a model-based control for an electromechanical lower-limb rehabilitation system based on a parallel kinematic mechanism. A controller-observer was designed for estimating joint velocities, which are then used in a hybrid position/force control scheme. The model parameters are identified by customising an approach based on identifying only the relevant system dynamics parameters. Findings obtained through simulations show evidence of improvement in tracking performance compared with those where the velocity was estimated by numerical differentiation. The controller is also implemented in an actual electromechanical system for lower-limb rehabilitation tasks. Findings based on rehabilitation tasks confirm the findings from simulations.This work was partially financed by the Plan Nacional de I+D, Comision Interministerial de Ciencia y Tecnologia (FEDERCICYT) under the project DPI2013-44227-R and by the Instituto U. de Automatica e Informatica Industrial (ai2) of the Universitat Politecnica de Valencia.Valera Fernández, Á.; Díaz-Rodríguez, M.; Vallés Miquel, M.; Oliver, E.; Mata Amela, V.; Page Del Pozo, AF. (2017). Controller-observer design and dynamic parameter identification for model-based control of an electromechanical lower-limb rehabilitation system. International Journal of Control. 90(4):702-714. https://doi.org/10.1080/00207179.2016.1215529S702714904Åström, K. J., & Murray, R. M. (2010). Feedback Systems. doi:10.2307/j.ctvcm4gdkAtkeson, C. G., An, C. H., & Hollerbach, J. M. (1986). Estimation of Inertial Parameters of Manipulator Loads and Links. The International Journal of Robotics Research, 5(3), 101-119. doi:10.1177/027836498600500306Chia Bejarano, N., Maggioni, S., De Rijcke, L., Cifuentes, C. A., & Reinkensmeyer, D. J. (2015). Robot-Assisted Rehabilitation Therapy: Recovery Mechanisms and Their Implications for Machine Design. Emerging Therapies in Neurorehabilitation II, 197-223. doi:10.1007/978-3-319-24901-8_8Berghuis, H., & Nijmeijer, H. (1993). A passivity approach to controller-observer design for robots. IEEE Transactions on Robotics and Automation, 9(6), 740-754. doi:10.1109/70.265918Briot, S., & Gautier, M. (2013). Global identification of joint drive gains and dynamic parameters of parallel robots. Multibody System Dynamics, 33(1), 3-26. doi:10.1007/s11044-013-9403-6Canudas de Wit, C., & Fixot, N. (1991). Robot control via robust estimated state feedback. IEEE Transactions on Automatic Control, 36(12), 1497-1501. doi:10.1109/9.106170Canudas de Wit, C., & Slotine, J.-J. E. (1991). Sliding observers for robot manipulators. Automatica, 27(5), 859-864. doi:10.1016/0005-1098(91)90041-yCao, J., Xie, S. Q., Das, R., & Zhu, G. L. (2014). Control strategies for effective robot assisted gait rehabilitation: The state of art and future prospects. Medical Engineering & Physics, 36(12), 1555-1566. doi:10.1016/j.medengphy.2014.08.005Carretero, J. A., Podhorodeski, R. P., Nahon, M. A., & Gosselin, C. M. (1999). Kinematic Analysis and Optimization of a New Three Degree-of-Freedom Spatial Parallel Manipulator. Journal of Mechanical Design, 122(1), 17-24. doi:10.1115/1.533542Cazalilla, J., Vallés, M., Mata, V., Díaz-Rodríguez, M., & Valera, A. (2014). Adaptive control of a 3-DOF parallel manipulator considering payload handling and relevant parameter models. Robotics and Computer-Integrated Manufacturing, 30(5), 468-477. doi:10.1016/j.rcim.2014.02.003De Jalon, J.G. & Bayo, E. (1994). Kinematic and dynamic simulation of multibody systems: the real-time challenge. New York: Springer Verlag.Díaz, I., Gil, J. J., & Sánchez, E. (2011). Lower-Limb Robotic Rehabilitation: Literature Review and Challenges. Journal of Robotics, 2011, 1-11. doi:10.1155/2011/759764Díaz-Rodríguez, M., Iriarte, X., Mata, V., & Ros, J. (2009). On the Experiment Design for Direct Dynamic Parameter Identification of Parallel Robots. Advanced Robotics, 23(3), 329-348. doi:10.1163/156855308x397550Díaz-Rodríguez, M., Mata, V., Valera, Á., & Page, Á. (2010). A methodology for dynamic parameters identification of 3-DOF parallel robots in terms of relevant parameters. Mechanism and Machine Theory, 45(9), 1337-1356. doi:10.1016/j.mechmachtheory.2010.04.007Gautier, M. (1991). Numerical calculation of the base inertial parameters of robots. Journal of Robotic Systems, 8(4), 485-506. doi:10.1002/rob.4620080405Gautier, M., & Khalil, W. (s. f.). On the identification of the inertial parameters of robots. Proceedings of the 27th IEEE Conference on Decision and Control. doi:10.1109/cdc.1988.194738Jamwal, P. K., Hussain, S., & Xie, S. Q. (2013). Review on design and control aspects of ankle rehabilitation robots. Disability and Rehabilitation: Assistive Technology, 10(2), 93-101. doi:10.3109/17483107.2013.866986Janabi-Sharifi, F., Hayward, V., & Chen, C.-S. J. (2000). Discrete-time adaptive windowing for velocity estimation. IEEE Transactions on Control Systems Technology, 8(6), 1003-1009. doi:10.1109/87.880606Janot, A., Gautier, M., Jubien, A., & Vandanjon, P. O. (2014). Comparison Between the CLOE Method and the DIDIM Method for Robots Identification. IEEE Transactions on Control Systems Technology, 22(5), 1935-1941. doi:10.1109/tcst.2014.2299544Janot, A., Vandanjon, P.-O., & Gautier, M. (2016). A revised Durbin-Wu-Hausman test for industrial robot identification. Control Engineering Practice, 48, 52-62. doi:10.1016/j.conengprac.2015.12.017Jiménez-Fabián, R., & Verlinden, O. (2012). Review of control algorithms for robotic ankle systems in lower-limb orthoses, prostheses, and exoskeletons. Medical Engineering & Physics, 34(4), 397-408. doi:10.1016/j.medengphy.2011.11.018Khalil, W., Vijayalingam, A., Khomutenko, B., Mukhanov, I., Lemoine, P., & Ecorchard, G. (2014). OpenSYMORO: An open-source software package for symbolic modelling of robots. 2014 IEEE/ASME International Conference on Advanced Intelligent Mechatronics. doi:10.1109/aim.2014.6878246Marchal-Crespo, L., & Reinkensmeyer, D. J. (2009). Review of control strategies for robotic movement training after neurologic injury. Journal of NeuroEngineering and Rehabilitation, 6(1). doi:10.1186/1743-0003-6-20Meng, W., Liu, Q., Zhou, Z., Ai, Q., Sheng, B., & Xie, S. (Shane). (2015). Recent development of mechanisms and control strategies for robot-assisted lower limb rehabilitation. Mechatronics, 31, 132-145. doi:10.1016/j.mechatronics.2015.04.005Page, A., Candelas, P., & Belmar, F. (2006). On the use of local fitting techniques for the analysis of physical dynamic systems. European Journal of Physics, 27(2), 273-279. doi:10.1088/0143-0807/27/2/010Raibert, M. H., & Craig, J. J. (1981). Hybrid Position/Force Control of Manipulators. Journal of Dynamic Systems, Measurement, and Control, 103(2), 126-133. doi:10.1115/1.3139652Ramsay, J. O., & Silverman, B. W. (2005). Functional Data Analysis. Springer Series in Statistics. doi:10.1007/b98888Saglia, J. A., Tsagarakis, N. G., Dai, J. S., & Caldwell, D. G. (2013). Control Strategies for Patient-Assisted Training Using the Ankle Rehabilitation Robot (ARBOT). IEEE/ASME Transactions on Mechatronics, 18(6), 1799-1808. doi:10.1109/tmech.2012.2214228Vallés, M., Cazalilla, J., Valera, Á., Mata, V., Page, Á., & Díaz-Rodríguez, M. (2015). A 3-PRS parallel manipulator for ankle rehabilitation: towards a low-cost robotic rehabilitation. Robotica, 35(10), 1939-1957. doi:10.1017/s0263574715000120Vallés, M., Cazalilla, J. I., Valera, Á., Mata, V., & Page, Á. (2013). Implementación basada en el middleware OROCOS de controladores dinámicos pasivos para un robot paralelo. Revista Iberoamericana de Automática e Informática Industrial RIAI, 10(1), 96-103. doi:10.1016/j.riai.2012.11.009Vallés, M., Díaz-Rodríguez, M., Valera, Á., Mata, V., & Page, Á. (2012). Mechatronic Development and Dynamic Control of a 3-DOF Parallel Manipulator. Mechanics Based Design of Structures and Machines, 40(4), 434-452. doi:10.1080/15397734.2012.687292Wu, F. X., Zhang, W. J., Li, Q., & Ouyang, P. R. (2002). Integrated Design and PD Control of High-Speed Closed-loop Mechanisms. Journal of Dynamic Systems, Measurement, and Control, 124(4), 522-528. doi:10.1115/1.1513179Yang, C., Huang, Q., & Han, J. (2012). Decoupling control for spatial six-degree-of-freedom electro-hydraulic parallel robot. Robotics and Computer-Integrated Manufacturing, 28(1), 14-23. doi:10.1016/j.rcim.2011.06.002Yoon, J., Ryu, J., & Lim, K.-B. (2006). Reconfigurable ankle rehabilitation robot for various exercises. Journal of Robotic Systems, 22(S1), S15-S33. doi:10.1002/rob.2015

From walking to running: robust and 3D humanoid gait generation via MPC

Humanoid robots are platforms that can succeed in tasks conceived for humans. From locomotion in unstructured environments, to driving cars, or working in industrial plants, these robots have a potential that is yet to be disclosed in systematic every-day-life applications. Such a perspective, however, is opposed by the need of solving complex engineering problems under the hardware and software point of view. In this thesis, we focus on the software side of the problem, and in particular on locomotion control. The operativity of a legged humanoid is subordinate to its capability of realizing a reliable locomotion. In many settings, perturbations may undermine the balance and make the robot fall. Moreover, complex and dynamic motions might be required by the context, as for instance it could be needed to start running or climbing stairs to achieve a certain location in the shortest time. We present gait generation schemes based on Model Predictive Control (MPC) that tackle both the problem of robustness and tridimensional dynamic motions. The proposed control schemes adopt the typical paradigm of centroidal MPC for reference motion generation, enforcing dynamic balance through the Zero Moment Point condition, plus a whole-body controller that maps the generated trajectories to joint commands. Each of the described predictive controllers also feature a so-called stability constraint, preventing the generation of diverging Center of Mass trajectories with respect to the Zero Moment Point. Robustness is addressed by modeling the humanoid as a Linear Inverted Pendulum and devising two types of strategies. For persistent perturbations, a way to use a disturbance observer and a technique for constraint tightening (to ensure robust constraint satisfaction) are presented. In the case of impulsive pushes instead, techniques for footstep and timing adaptation are introduced. The underlying approach is to interpret robustness as a MPC feasibility problem, thus aiming at ensuring the existence of a solution for the constrained optimization problem to be solved at each iteration in spite of the perturbations. This perspective allows to devise simple solutions to complex problems, favoring a reliable real-time implementation. For the tridimensional locomotion, on the other hand, the humanoid is modeled as a Variable Height Inverted Pendulum. Based on it, a two stage MPC is introduced with particular emphasis on the implementation of the stability constraint. The overall result is a gait generation scheme that allows the robot to overcome relatively complex environments constituted by a non-flat terrain, with also the capability of realizing running gaits. The proposed methods are validated in different settings: from conceptual simulations in Matlab to validations in the DART dynamic environment, up to experimental tests on the NAO and the OP3 platforms