Objective measurement of habitual sedentary behavior in pre-school children: comparison of activPAL with actigraph monitors

The Actigraph is well established for measurement of both physical activity and sedentary behavior in children. The activPAL is being used increasingly in children, though with no published evidence on its use in free-living children to date. The present study compared the two monitors in preschool children. Children (n 23) wore both monitors simultaneously during waking hours for 5.6d and 10h/d. Daily mean percentage of time sedentary (nontranslocation of the trunk) was 74.6 (SD 6.8) for the Actigraph and 78.9 (SD 4.3) for activPAL. Daily mean percentage of time physically active (light intensity physical activity plus MVPA) was 25.4 (SD 6.8) for the Actigraph and 21.1 (SD 4.3) for the activPAL. Bland-Altman tests and paired t tests suggested small but statistically significant differences between the two monitors. Actigraph and activPAL estimates of sedentary behaviour and physical activity in young children are similar at a group level

Damage detection in beams from modal and wavelet analysis using a stationary roving mass and noise estimation

This paper uses the Continuous Wavelet Transform Analysis on mode shapes for damage identification. The wavelet analysis is applied to the difference in the mode shapes between a healthy and a damaged state. The paper also includes a novel methodology for estimating the level of noise of the experimental mode shapes based on a standard Signal to Noise Ratio (SNR). The estimated SNRs are used for identifying and making emphasis on the less noisy data. Moreover, a mass attached to the structure is considered to enhance the sensitivity of the structure to damage. Modal analysis is performed for different positions of the mass along the beam. The results obtained for all the positions of the mass are combined so an averaging process is implicitly applied. The paper presents the results from an experimental test of a cantilever steel beam with different severity levels of damage at the same location. The results show that the use of the attached mass reduces the effect of noise and increases the sensitivity to damage. Little damage can be identified with the proposed methodology even using a small number of sensors and only the first five bending modesConsejería de Economía, Innovación, Ciencia y Empleo, Junta de Andalucía. Grant Number: P12-TEP-2546Ministerio de Economía y Competitividad. Grant Numbers: BIA2013-43085-P, BIA2016-75042-C2-1-

Vibration-based condition monitoring of wind turbine blades

Significant advances in wind turbine technology have increased the need for maintenance through condition monitoring. Indeed condition monitoring techniques exist and are deployed on wind turbines across Europe and America but are limited in scope. The sensors and monitoring devices used can be very expensive to deploy, further increasing costs within the wind industry. The work outlined in this thesis primarily investigates potential low-cost alternatives in the laboratory environment using vibration-based and modal testing techniques that could be used to monitor the condition of wind turbine blades. The main contributions of this thesis are: (1) the review of vibration-based condition monitoring for changing natural frequency identification; (2) the application of low-cost piezoelectric sounders with proof mass for sensing and measuring vibrations which provide information on structural health; (3) the application of low-cost miniature Micro-Electro-Mechanical Systems (MEMS) accelerometers for detecting and measuring defects in micro wind turbine blades in laboratory experiments; (4) development of an in-service calibration technique for arbitrarily positioned MEMS accelerometers on a medium-sized wind turbine blade. This allowed for easier aligning of coordinate systems and setting the accelerometer calibration values using samples taken over a period of time; (5) laboratory validation of low-cost modal analysis techniques on a medium-sized wind turbine blade; (6) mimicked ice-loading and laboratory measurement of vibration characteristics using MEMS accelerometers on a real wind turbine blade and (7) conceptualisation and systems design of a novel embedded monitoring system that can be installed at manufacture, is self-powered, has signal processing capability and can operate remotely. By applying the conclusions of this work, which demonstrates that low-cost consumer electronics specifically MEMS accelerometers can measure the vibration characteristics of wind turbine blades, the implementation and deployment of these devices can contribute towards reducing the rising costs of condition monitoring within the wind industry