Design-for-Test and Test Optimization Techniques for TSV-based 3D Stacked ICs

<p>As integrated circuits (ICs) continue to scale to smaller dimensions, long interconnects</p><p>have become the dominant contributor to circuit delay and a significant component of</p><p>power consumption. In order to reduce the length of these interconnects, 3D integration</p><p>and 3D stacked ICs (3D SICs) are active areas of research in both academia and industry.</p><p>3D SICs not only have the potential to reduce average interconnect length and alleviate</p><p>many of the problems caused by long global interconnects, but they can offer greater design</p><p>flexibility over 2D ICs, significant reductions in power consumption and footprint in</p><p>an era of mobile applications, increased on-chip data bandwidth through delay reduction,</p><p>and improved heterogeneous integration.</p><p>Compared to 2D ICs, the manufacture and test of 3D ICs is significantly more complex.</p><p>Through-silicon vias (TSVs), which constitute the dense vertical interconnects in a</p><p>die stack, are a source of additional and unique defects not seen before in ICs. At the same</p><p>time, testing these TSVs, especially before die stacking, is recognized as a major challenge.</p><p>The testing of a 3D stack is constrained by limited test access, test pin availability,</p><p>power, and thermal constraints. Therefore, efficient and optimized test architectures are</p><p>needed to ensure that pre-bond, partial, and complete stack testing are not prohibitively</p><p>expensive.</p><p>Methods of testing TSVs prior to bonding continue to be a difficult problem due to test</p><p>access and testability issues. Although some built-in self-test (BIST) techniques have been</p><p>proposed, these techniques have numerous drawbacks that render them impractical. In this dissertation, a low-cost test architecture is introduced to enable pre-bond TSV test through</p><p>TSV probing. This has the benefit of not needing large analog test components on the die,</p><p>which is a significant drawback of many BIST architectures. Coupled with an optimization</p><p>method described in this dissertation to create parallel test groups for TSVs, test time for</p><p>pre-bond TSV tests can be significantly reduced. The pre-bond probing methodology is</p><p>expanded upon to allow for pre-bond scan test as well, to enable both pre-bond TSV and</p><p>structural test to bring pre-bond known-good-die (KGD) test under a single test paradigm.</p><p>The addition of boundary registers on functional TSV paths required for pre-bond</p><p>probing results in an increase in delay on inter-die functional paths. This cost of test</p><p>architecture insertion can be a significant drawback, especially considering that one benefit</p><p>of 3D integration is that critical paths can be partitioned between dies to reduce their delay.</p><p>This dissertation derives a retiming flow that is used to recover the additional delay added</p><p>to TSV paths by test cell insertion.</p><p>Reducing the cost of test for 3D-SICs is crucial considering that more tests are necessary</p><p>during 3D-SIC manufacturing. To reduce test cost, the test architecture and test</p><p>scheduling for the stack must be optimized to reduce test time across all necessary test</p><p>insertions. This dissertation examines three paradigms for 3D integration - hard dies, firm</p><p>dies, and soft dies, that give varying degrees of control over 2D test architectures on each</p><p>die while optimizing the 3D test architecture. Integer linear programming models are developed</p><p>to provide an optimal 3D test architecture and test schedule for the dies in the 3D</p><p>stack considering any or all post-bond test insertions. Results show that the ILP models</p><p>outperform other optimization methods across a range of 3D benchmark circuits.</p><p>In summary, this dissertation targets testing and design-for-test (DFT) of 3D SICs.</p><p>The proposed techniques enable pre-bond TSV and structural test while maintaining a</p><p>relatively low test cost. Future work will continue to enable testing of 3D SICs to move</p><p>industry closer to realizing the true potential of 3D integration.</p>Dissertatio

Reliability-Constrained Die Stacking Order in 3DICs Under Manufacturing Variability

Abstract—3D integrated circuits (3DICs) with through-silicon vias (TSVs) are an important direction for semiconductor-based products and “More than Moore ” scaling. However, 3DICs bring simultaneous challenges of reliability (power and temperature in stacks of thinned die) as well as variability (performance and power) in advanced technology nodes. In this paper, we study variability-reliability interactions and optimizations in 3DICs. Initial motivating studies show that in the presence of manufacturing variability, different die stacking orders can lead to as much as 2 years (∼44%) difference in MTTF of a 3DIC stack. We study MTTF-driven die-stacking optimization with consideration of variability, and propose a “rule-of-thumb ” guideline for stacking optimization to improve peak temperature as well as reliability in 3DICs. We also propose integer-linear programming (ILP) methods for reliability-driven die-stacking optimization. Our methods can achieve ∼7 % and ∼28 % improvement in average and minimum MTTF, respectively, of 3DICs; we also achieve ∼3 % improvement in performance under fixed reliability constraints. Our stacking optimizations can help improve 3DIC product yields under reliability requirements. Our research also yields the notable observation that a limited amount of manufacturing variation can “help ” improve 3DIC product reliability when die-stacking optimization is applied. I