On the design of an Ohmic RF MEMS switch for reconfigurable microstrip antenna applications

This paper presents the analysis, design and simulation of a direct contact (dc) RF MEMS switch specified for reconfigurable microstrip array antennas. The proposed switch is indented to be built on PCB via a monolithic technology together with the antenna patches. The proposed switch will be used to allow antenna beamforming in the operating frequency range between 2GHz and 4GHz. This application requires a great number of these switches to be integrated with an array of microstrip patch elements. The proposed switch fulfills the switching characteristics as concerns the five requirements (loss, linearity, voltage/power handling, small size/power consumption, temperature), following a relatively simple design, which ensures reliability, robustness and high fabrication yiel

An Electronically Reconfigurable Patch Antenna Design for Polarization Diversity with Fixed Resonant Frequency

In this paper, an electronically polarization reconfigurable circular patch antenna with fixed resonant frequency operating at Wireless Local Area Network (WLAN) frequency band (2.4-2.48 GHz) is presented. The structure of the proposed design consists of a circular patch as a radiating element fed by coaxial probe, cooperated with four equal-length slits etched on the edge along x-axis and y-axis. A total of four switches was used and embedded across the slits at specific locations, thus controlled the length of the slits. By activating and deactivating the switches (ON and OFF) across the slits, the current on the patch is changed, thus modifying the electric field and polarization of the antenna. Consequently, the polarization excited by the proposed antenna can be switched into three types, either linear polarization, left-hand circular polarization or right-hand circular polarization. This paper proposes a simple approach that able to switch the polarizations and excited at the same operating frequency. Simulated and measured results of ideal case (using copper strip switches) and real case (using PIN diode switches) are compared and presented to demonstrate the performance of the antenna

A FPGA-Based Reconfigurable Software Architecture for Highly Dependable Systems

Nowadays, systems-on-chip are commonly equipped with reconfigurable hardware. The use of hybrid architectures based on a mixture of general purpose processors and reconfigurable components has gained importance across the scientific community allowing a significant improvement of computational performance. Along with the demand for performance, the great sensitivity of reconfigurable hardware devices to physical defects lead to the request of highly dependable and fault tolerant systems. This paper proposes an FPGA-based reconfigurable software architecture able to abstract the underlying hardware platform giving an homogeneous view of it. The abstraction mechanism is used to implement fault tolerance mechanisms with a minimum impact on the system performanc

Single-, Dual- and Triple-band Frequency Reconfigurable Antenna

The paper presents a frequency reconfigurable slot dipole antenna. The antenna is capable of being switched between single-band, dual-band or triple-band operation. The antenna incorporates three pairs of pin-diodes which are located within the dipole arms. The antenna was designed to operate at 2.4 GHz, 3.5 GHz and 5.2 GHz using the aid of CST Microwave Studio. The average measured gains are 1.54, 2.92 and 1.89 dBi for low, mid and high band respectively. A prototype was then constructed in order to verify the performance of the device. A good level of agreement was observed between simulation and measurement

Switched Capacitor DC-DC Converter for Miniaturised Wearable Systems

Motivated by the demands of the integrated power system in the modern wearable electronics, this paper presents a new method of inductor-less switched-capacitor (SC) based DC-DC converter designed to produce two simultaneous boost and buck outputs by using a 4-phases logic switch mode regulation. While the existing SC converters missing their reconfigurability during needed spontaneous multi-outputs at the load ends, this work overcomes this limitation by being able to reconfigure higher gain mode at dual outputs. From an input voltage of 2.5 V, the proposed converter achieves step-up and step-down voltage conversions of 3.74 V and 1.233 V for Normal mode, and 4.872 V and 2.48 V for High mode, with the ripple variation of 20–60 mV. The proposed converter has been designed in a standard 0.35 μm CMOS technology and with conversion efficiencies up to 97–98% is in agreement with state-of-the-art SC converter designs. It produces the maximum load currents of 0.21 mA and 0.37 mA for Normal and High modes respectively. Due to the flexible gain accessibility and fast response time with only two clock cycles required for steady state outputs, this converter can be applicable for multi-function wearable devices, comprised of various integrated electronic modules

A committee machine gas identification system based on dynamically reconfigurable FPGA

This paper proposes a gas identification system based on the committee machine (CM) classifier, which combines various gas identification algorithms, to obtain a unified decision with improved accuracy. The CM combines five different classifiers: K nearest neighbors (KNNs), multilayer perceptron (MLP), radial basis function (RBF), Gaussian mixture model (GMM), and probabilistic principal component analysis (PPCA). Experiments on real sensors' data proved the effectiveness of our system with an improved accuracy over individual classifiers. Due to the computationally intensive nature of CM, its implementation requires significant hardware resources. In order to overcome this problem, we propose a novel time multiplexing hardware implementation using a dynamically reconfigurable field programmable gate array (FPGA) platform. The processing is divided into three stages: sampling and preprocessing, pattern recognition, and decision stage. Dynamically reconfigurable FPGA technique is used to implement the system in a sequential manner, thus using limited hardware resources of the FPGA chip. The system is successfully tested for combustible gas identification application using our in-house tin-oxide gas sensors