Low-cost, low-power FPGA implementation of ED25519 and CURVE25519 point multiplication

Twisted Edwards curves have been at the center of attention since their introduction by Bernstein et al. in 2007. The curve ED25519, used for Edwards-curve Digital Signature Algorithm (EdDSA), provides faster digital signatures than existing schemes without sacrificing security. The CURVE25519 is a Montgomery curve that is closely related to ED25519. It provides a simple, constant time, and fast point multiplication, which is used by the key exchange protocol X25519. Software implementations of EdDSA and X25519 are used in many web-based PC and Mobile applications. In this paper, we introduce a low-power, low-area FPGA implementation of the ED25519 and CURVE25519 scalar multiplication that is particularly relevant for Internet of Things (IoT) applications. The efficiency of the arithmetic modulo the prime number 2 255 − 19, in particular the modular reduction and modular multiplication, are key to the efficiency of both EdDSA and X25519. To reduce the complexity of the hardware implementation, we propose a high-radix interleaved modular multiplication algorithm. One benefit of this architecture is to avoid the use of large-integer multipliers relying on FPGA DSP modules

Speed and Area Optimized Parallel Higher-Radix Modular Multipliers

Modular multiplication is the fundamental and compute-intense operation in many Public-Key crypto-systems. This paper presents two modular multipliers with their efficient architectures based on Booth encoding, higher-radix, and Montgomery powering ladder approaches. Montgomery powering ladder technique enables concurrent execution of main operations in the proposed designs, while higher-radix techniques have been adopted to reduce an iteration count which formally dictates a cycle count. It is also shown that by an adopting Booth encoding logic in the designs helps to reduce their area cost with a slight degradation in the maximum achievable frequencies. The proposed designs are implemented in Verilog HDL and synthesized targeting virtex-6 FPGA platform using Xilinx ISE 14.2 Design suite. The radix-4 multiplier computes a 256-bit modular multiplication in 0.93 ms, occupies 1.6K slices, at 137.87 MHz in a cycle count of n/2+2, whereas the radix-8 multiplier completes the operation in 0.69ms, occupies 3.6K slices, achieves 123.43 MHz frequency in a cycle count of n/3+4. The implementation results reveals that the proposed designs consumes 18% lower FPGA slices without any significant performance degradation as compared to their best contemporary designs

FPGA Based High Speed SPA Resistant Elliptic Curve Scalar Multiplier Architecture

The higher computational complexity of an elliptic curve scalar point multiplication operation limits its implementation on general purpose processors. Dedicated hardware architectures are essential to reduce the computational time, which results in a substantial increase in the performance of associated cryptographic protocols. This paper presents a unified architecture to compute modular addition, subtraction, and multiplication operations over a finite field of large prime characteristic GF(p). Subsequently, dual instances of the unified architecture are utilized in the design of high speed elliptic curve scalar multiplier architecture. The proposed architecture is synthesized and implemented on several different Xilinx FPGA platforms for different field sizes. The proposed design computes a 192-bit elliptic curve scalar multiplication in 2.3 ms on Virtex-4 FPGA platform. It is 34% faster and requires 40% fewer clock cycles for elliptic curve scalar multiplication and consumes considerable fewer FPGA slices as compared to the other existing designs. The proposed design is also resistant to the timing and simple power analysis (SPA) attacks; therefore it is a good choice in the construction of fast and secure elliptic curve based cryptographic protocols

Unified field multiplier for GF(p) and GF(2 n) with novel digit encoding

In recent years, there has been an increase in demand for unified field multipliers for Elliptic Curve Cryptography in the electronics industry because they provide flexibility for customers to choose between Prime (GF(p)) and Binary (GF(2")) Galois Fields. Also, having the ability to carry out arithmetic over both GF(p) and GF(2") in the same hardware provides the possibility of performing any cryptographic operation that requires the use of both fields. The unified field multiplier is relatively future proof compared with multipliers that only perform arithmetic over a single chosen field. The security provided by the architecture is also very important. It is known that the longer the key length, the more susceptible the system is to differential power attacks due to the increased amount of data leakage. Therefore, it is beneficial to design hardware that is scalable, so that more data can be processed per cycle. Another advantage of designing a multiplier that is capable of dealing with long word length is improvement in performance in terms of delay, because less cycles are needed. This is very important because typical elliptic curve cryptography involves key size of 160 bits. A novel unified field radix-4 multiplier using Montgomery Multiplication for the use of G(p) and GF(2") has been proposed. This design makes use of the unexploited state in number representation for operation in GF(2") where all carries are suppressed. The addition is carried out using a modified (4:2) redundant adder to accommodate the extra 1 * state. The proposed adder and the partial product generator design are capable of radix-4 operation, which reduces the number of computation cycles required. Also, the proposed adder is more scalable than existing designs.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Unified field multiplier for GF(p) and GF(2 n) with novel digit encoding

In recent years, there has been an increase in demand for unified field multipliers for Elliptic Curve Cryptography in the electronics industry because they provide flexibility for customers to choose between Prime (GF(p)) and Binary (GF(2')) Galois Fields. Also, having the ability to carry out arithmetic over both GF(p) and GF(2') in the same hardware provides the possibility of performing any cryptographic operation that requires the use of both fields. The unified field multiplier is relatively future proof compared with multipliers that only perform arithmetic over a single chosen field. The security provided by the architecture is also very important. It is known that the longer the key length, the more susceptible the system is to differential power attacks due to the increased amount of data leakage. Therefore, it is beneficial to design hardware that is scalable, so that more data can be processed per cycle. Another advantage of designing a multiplier that is capable of dealing with long word length is improvement in performance in terms of delay, because less cycles are needed. This is very important because typical elliptic curve cryptography involves key size of 160 bits. A novel unified field radix-4 multiplier using Montgomery Multiplication for the use of G(p) and GF(2') has been proposed. This design makes use of the unexploited state in number representation for operation in GF(2') where all carries are suppressed. The addition is carried out using a modified (4:2) redundant adder to accommodate the extra 1 * state. The proposed adder and the partial product generator design are capable of radix-4 operation, which reduces the number of computation cycles required. Also, the proposed adder is more scalable than existing designs

The Fifth NASA Symposium on VLSI Design

The fifth annual NASA Symposium on VLSI Design had 13 sessions including Radiation Effects, Architectures, Mixed Signal, Design Techniques, Fault Testing, Synthesis, Signal Processing, and other Featured Presentations. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The presentations share insights into next generation advances that will serve as a basis for future VLSI design

Tools and Algorithms for the Construction and Analysis of Systems

This open access two-volume set constitutes the proceedings of the 27th International Conference on Tools and Algorithms for the Construction and Analysis of Systems, TACAS 2021, which was held during March 27 – April 1, 2021, as part of the European Joint Conferences on Theory and Practice of Software, ETAPS 2021. The conference was planned to take place in Luxembourg and changed to an online format due to the COVID-19 pandemic. The total of 41 full papers presented in the proceedings was carefully reviewed and selected from 141 submissions. The volume also contains 7 tool papers; 6 Tool Demo papers, 9 SV-Comp Competition Papers. The papers are organized in topical sections as follows: Part I: Game Theory; SMT Verification; Probabilities; Timed Systems; Neural Networks; Analysis of Network Communication. Part II: Verification Techniques (not SMT); Case Studies; Proof Generation/Validation; Tool Papers; Tool Demo Papers; SV-Comp Tool Competition Papers

Applications of microprocessors in digital high frequency radio communications

This thesis describes the application of VLSI devices to channel evaluation and communication techniques over ionospheric radio paths. Digital signal processing techniques using microprocessors and charge coupled devices are described in detail. A novel method for observing interference and fading patterns on HF channels is described. Error control coding schemes and digital modulation techniques are combined in a design for an adaptive modem for use over HF radio links. Results of narrow-band interference measurements, error patterns and coding performance are presented

Proceedings of the 5th International Workshop on Reconfigurable Communication-centric Systems on Chip 2010 - ReCoSoC\u2710 - May 17-19, 2010 Karlsruhe, Germany. (KIT Scientific Reports ; 7551)

ReCoSoC is intended to be a periodic annual meeting to expose and discuss gathered expertise as well as state of the art research around SoC related topics through plenary invited papers and posters. The workshop aims to provide a prospective view of tomorrow\u27s challenges in the multibillion transistor era, taking into account the emerging techniques and architectures exploring the synergy between flexible on-chip communication and system reconfigurability