Interference mitigation in cognitive femtocell networks

“A thesis submitted to the University of Bedfordshire, in partial fulfilment of the requirements for the degree of Doctor of Philosophy”.Femtocells have been introduced as a solution to poor indoor coverage in cellular communication which has hugely attracted network operators and stakeholders. However, femtocells are designed to co-exist alongside macrocells providing improved spatial frequency reuse and higher spectrum efficiency to name a few. Therefore, when deployed in the two-tier architecture with macrocells, it is necessary to mitigate the inherent co-tier and cross-tier interference. The integration of cognitive radio (CR) in femtocells introduces the ability of femtocells to dynamically adapt to varying network conditions through learning and reasoning. This research work focuses on the exploitation of cognitive radio in femtocells to mitigate the mutual interference caused in the two-tier architecture. The research work presents original contributions in mitigating interference in femtocells by introducing practical approaches which comprises a power control scheme where femtocells adaptively controls its transmit power levels to reduce the interference it causes in a network. This is especially useful since femtocells are user deployed as this seeks to mitigate interference based on their blind placement in an indoor environment. Hybrid interference mitigation schemes which combine power control and resource/scheduling are also implemented. In a joint threshold power based admittance and contention free resource allocation scheme, the mutual interference between a Femtocell Access Point (FAP) and close-by User Equipments (UE) is mitigated based on admittance. Also, a hybrid scheme where FAPs opportunistically use Resource Blocks (RB) of Macrocell User Equipments (MUE) based on its traffic load use is also employed. Simulation analysis present improvements when these schemes are applied with emphasis in Long Term Evolution (LTE) networks especially in terms of Signal to Interference plus Noise Ratio (SINR)

MM-Wave HetNet in 5G and beyond Cellular Networks Reinforcement Learning Method to improve QoS and Exploiting Path Loss Model

This paper presents High density heterogeneous networks (HetNet) which are the most promising technology for the fifth generation (5G) cellular network. Since 5G will be available for a long time, previous generation networking systems will need customization and updates. We examine the merits and drawbacks of legacy and Q-Learning (QL)-based adaptive resource allocation systems. Furthermore, various comparisons between methods and schemes are made for the purpose of evaluating the solutions for future generation. Microwave macro cells are used to enable extra high capacity such as Long-Term Evolution (LTE), eNodeB (eNB), and Multimedia Communications Wireless technology (MC), in which they are most likely to be deployed. This paper also presents four scenarios for 5G mm-Wave implementation, including proposed system architectures. The WL algorithm allocates optimal power to the small cell base station (SBS) to satisfy the minimum necessary capacity of macro cell user equipment (MUEs) and small cell user equipment (SCUEs) in order to provide quality of service (QoS) (SUEs). The challenges with dense HetNet and the massive backhaul traffic they generate are discussed in this study. Finally, a core HetNet design based on clusters is aimed at reducing backhaul traffic. According to our findings, MM-wave HetNet and MEC can be useful in a wide range of applications, including ultra-high data rate and low latency communications in 5G and beyond. We also used the channel model simulator to examine the directional power delay profile with received signal power, path loss, and path loss exponent (PLE) for both LOS and NLOS using uniform linear array (ULA) 2X2 and 64x16 antenna configurations at 38 GHz and 73 GHz mmWave bands for both LOS and NLOS (NYUSIM). The simulation results show the performance of several path loss models in the mmWave and sub-6 GHz bands. The path loss in the close-in (CI) model at mmWave bands is higher than that of open space and two ray path loss models because it considers all shadowing and reflection effects between transmitter and receiver. We also compared the suggested method to existing models like Amiri, Su, Alsobhi, Iqbal, and greedy (non adaptive), and found that it not only enhanced MUE and SUE minimum capacities and reduced BT complexity, but it also established a new minimum QoS threshold. We also talked about 6G researches in the future. When compared to utilizing the dual slope route loss model alone in a hybrid heterogeneous network, our simulation findings show that decoupling is more visible when employing the dual slope path loss model, which enhances system performance in terms of coverage and data rate

Optimization of 5G Second Phase Heterogeneous Radio Access Networks with Small Cells

Due to the exponential increase in high data-demanding applications and their services per coverage area, it is becoming challenging for the existing cellular network to handle the massive sum of users with their demands. It is conceded to network operators that the current wireless network may not be capable to shelter future traffic demands. To overcome the challenges the operators are taking interest in efficiently deploying the heterogeneous network. Currently, 5G is in the commercialization phase. Network evolution with addition of small cells will develop the existing wireless network with its enriched capabilities and innovative features. Presently, the 5G global standardization has introduced the 5G New Radio (NR) under the 3rd Generation Partnership Project (3GPP). It can support a wide range of frequency bands (<6 GHz to 100 GHz). For different trends and verticals, 5G NR encounters, functional splitting and its cost evaluation are well-thought-out. The aspects of network slicing to the assessment of the business opportunities and allied standardization endeavours are illustrated. The study explores the carrier aggregation (Pico cellular) technique for 4G to bring high spectral efficiency with the support of small cell massification while benefiting from statistical multiplexing gain. One has been able to obtain values for the goodput considering CA in LTE-Sim (4G), of 40 Mbps for a cell radius of 500 m and of 29 Mbps for a cell radius of 50 m, which is 3 times higher than without CA scenario (2.6 GHz plus 3.5 GHz frequency bands). Heterogeneous networks have been under investigation for many years. Heterogeneous network can improve users service quality and resource utilization compared to homogeneous networks. Quality of service can be enhanced by putting the small cells (Femtocells or Picocells) inside the Microcells or Macrocells coverage area. Deploying indoor Femtocells for 5G inside the Macro cellular network can reduce the network cost. Some service providers have started their solutions for indoor users but there are still many challenges to be addressed. The 5G air-simulator is updated to deploy indoor Femto-cell with proposed assumptions with uniform distribution. For all the possible combinations of apartments side length and transmitter power, the maximum number of supported numbers surpassed the number of users by more than two times compared to papers mentioned in the literature. Within outdoor environments, this study also proposed small cells optimization by putting the Pico cells within a Macro cell to obtain low latency and high data rate with the statistical multiplexing gain of the associated users. Results are presented 5G NR functional split six and split seven, for three frequency bands (2.6 GHz, 3.5GHz and 5.62 GHz). Based on the analysis for shorter radius values, the best is to select the 2.6 GHz to achieve lower PLR and to support a higher number of users, with better goodput, and higher profit (for cell radius u to 400 m). In 4G, with CA, from the analysis of the economic trade-off with Picocell, the Enhanced multi-band scheduler EMBS provide higher revenue, compared to those without CA. It is clearly shown that the profit of CA is more than 4 times than in the without CA scenario. This means that the slight increase in the cost of CA gives back more than 4-time profit relatively to the ”without” CA scenario.Devido ao aumento exponencial de aplicações/serviços de elevado débito por unidade de área, torna-se bastante exigente, para a rede celular existente, lidar com a enormes quantidades de utilizadores e seus requisitos. É reconhecido que as redes móveis e sem fios atuais podem não conseguir suportar a procura de tráfego junto dos operadores. Para responder a estes desafios, os operadores estão-se a interessar pelo desenvolvimento de redes heterogéneas eficientes. Atualmente, a 5G está na fase de comercialização. A evolução destas redes concretizar-se-á com a introdução de pequenas células com aptidões melhoradas e características inovadoras. No presente, os organismos de normalização da 5G globais introduziram os Novos Rádios (NR) 5G no contexto do 3rd Generation Partnership Project (3GPP). A 5G pode suportar uma gama alargada de bandas de frequência (<6 a 100 GHz). Abordam-se as divisões funcionais e avaliam-se os seus custos para as diferentes tendências e verticais dos NR 5G. Ilustram-se desde os aspetos de particionamento funcional da rede à avaliação das oportunidades de negócio, aliadas aos esforços de normalização. Exploram-se as técnicas de agregação de espetro (do inglês, CA) para pico células, em 4G, a disponibilização de eficiência espetral, com o suporte da massificação de pequenas células, e o ganho de multiplexagem estatística associado. Obtiveram-se valores do débito binário útil, considerando CA no LTE-Sim (4G), de 40 e 29 Mb/s para células de raios 500 e 50 m, respetivamente, três vezes superiores em relação ao caso sem CA (bandas de 2.6 mais 3.5 GHz). Nas redes heterogéneas, alvo de investigação há vários anos, a qualidade de serviço e a utilização de recursos podem ser melhoradas colocando pequenas células (femto- ou pico-células) dentro da área de cobertura de micro- ou macro-células). O desenvolvimento de pequenas células 5G dentro da rede com macro-células pode reduzir os custos da rede. Alguns prestadores de serviços iniciaram as suas soluções para ambientes de interior, mas ainda existem muitos desafios a ser ultrapassados. Atualizou-se o 5G air simulator para representar a implantação de femto-células de interior com os pressupostos propostos e distribuição espacial uniforme. Para todas as combinações possíveis do comprimento lado do apartamento, o número máximo de utilizadores suportado ultrapassou o número de utilizadores suportado (na literatura) em mais de duas vezes. Em ambientes de exterior, propuseram-se pico-células no interior de macro-células, de forma a obter atraso extremo-a-extremo reduzido e taxa de transmissão dados elevada, resultante do ganho de multiplexagem estatística associado. Apresentam-se resultados para as divisões funcionais seis e sete dos NR 5G, para 2.6 GHz, 3.5GHz e 5.62 GHz. Para raios das células curtos, a melhor solução será selecionar a banda dos 2.6 GHz para alcançar PLR (do inglês, PLR) reduzido e suportar um maior número de utilizadores, com débito binário útil e lucro mais elevados (para raios das células até 400 m). Em 4G, com CA, da análise do equilíbrio custos-proveitos com pico-células, o escalonamento multi-banda EMBS (do inglês, Enhanced Multi-band Scheduler) disponibiliza proveitos superiores em comparação com o caso sem CA. Mostra-se claramente que lucro com CA é mais de quatro vezes superior do que no cenário sem CA, o que significa que um aumento ligeiro no custo com CA resulta num aumento de 4-vezes no lucro relativamente ao cenário sem CA

Towards 5G Cellular: Understanding 3D In-Building Single Band and Multi-band Small Cells with Control/User-plane Coupled and Separation Architectures with a Novel Resource Reuse Approach

In this paper, we present numerous small cell base station, i.e. femtocell base station (FCBS), with control-/user-plane coupled and separation architectures based on the number of transceivers and operating frequency bands to serve control-/user-plane traffic. A single transceiver enabled FCBS can operate at either a co-channel microwave of the overlaid macrocell or a millimeter wave band. For multiple transceivers, dual transceivers are considered operating at both bands. FCBSs are deployed in a number of buildings with each floor modeled as 5×5 square-grid apartments. The co-channel interference with FCBSs is avoided using enhanced intercell interference coordination techniques. We propose a static frequency reuse approach and develop an algorithm by avoiding adjacent channel interferences from reusing frequencies in FCBSs. We also develop a resource scheduling algorithm for FCBSs with CUCA and CUSA to evaluate system level performances with a multi-tier network. It is found that a single transceiver co-channel microwave enabled FCBS with CUCA provides the worse, whereas a single or dual transceivers millimeter wave enabled FCBS with CUSA provides the best overall system capacity and FCBSs’ energy efficiency performances. Besides, we show the outperformances of the proposed resource reuse approach over an existing approach in literature in terms of system capacity and fairness among FCBSs with CUCA. Finally, we point out the applicability of a multi-band enabled FCBS and several features and issues of FCBSs with CUCA and CUSA.In this paper, we present numerous small cell base station, i.e. femtocell base station (FCBS), with control-/user-plane coupled and separation architectures based on the number of transceivers and operating frequency bands to serve control-/user-plane traffic. A single transceiver enabled FCBS can operate at either a co-channel microwave of the overlaid macrocell or a millimeter wave band. For multiple transceivers, dual transceivers are considered operating at both bands. FCBSs are deployed in a number of buildings with each floor modeled as 5 by&nbsp;5 square-grid apartments. The co-channel interference with FCBSs is avoided using enhanced intercell interference coordination techniques. We propose a static frequency reuse approach and develop an algorithm by avoiding adjacent channel interferences from reusing frequencies in FCBSs. We also develop a resource scheduling algorithm for FCBSs with CUCA and CUSA to evaluate system level performances with a multi-tier network. It is found that a single transceiver co-channel microwave enabled FCBS with CUCA provides the worse, whereas a single or dual transceivers millimeter wave enabled FCBS with CUSA provides the best overall system capacity and FCBSs' energy efficiency performances. Besides, we show the outperformances of the proposed resource reuse approach over an existing approach in literature in terms of system capacity and fairness among FCBSs with CUCA. Finally, we point out the applicability of a multi-band enabled FCBS and several features and issues of FCBSs with CUCA and CUSA

Millimetre wave frequency band as a candidate spectrum for 5G network architecture : a survey

In order to meet the huge growth in global mobile data traffic in 2020 and beyond, the development of the 5th Generation (5G) system is required as the current 4G system is expected to fall short of the provision needed for such growth. 5G is anticipated to use a higher carrier frequency in the millimetre wave (mm-wave) band, within the 20 to 90 GHz, due to the availability of a vast amount of unexploited bandwidth. It is a revolutionary step to use these bands because of their different propagation characteristics, severe atmospheric attenuation, and hardware constraints. In this paper, we carry out a survey of 5G research contributions and proposed design architectures based on mm-wave communications. We present and discuss the use of mm-wave as indoor and outdoor mobile access, as a wireless backhaul solution, and as a key enabler for higher order sectorisation. Wireless standards such as IEE802.11ad, which are operating in mm-wave band have been presented. These standards have been designed for short range, ultra high data throughput systems in the 60 GHz band. Furthermore, this survey provides new insights regarding relevant and open issues in adopting mm-wave for 5G networks. This includes increased handoff rate and interference in Ultra-Dense Network (UDN), waveform consideration with higher spectral efficiency, and supporting spatial multiplexing in mm-wave line of sight. This survey also introduces a distributed base station architecture in mm-wave as an approach to address increased handoff rate in UDN, and to provide an alternative way for network densification in a time and cost effective manner

Cooperative Radio Communications for Green Smart Environments

The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin

Performance evaluation of future wireless networks: node cooperation and aerial networks

Perhaps future historians will only refer to this era as the \emph{information age}, and will recognize it as a paramount milestone in mankind progress. One of the main pillars of this age is the ability to transmit and communicate information effectively and reliably, where wireless radio technology became one of the most vital enablers for such communication. A growth in radio communication demand is notably accelerating in a never-resting pace, pausing a great challenge not only on service providers but also on researches and innovators to explore out-of-the-box technologies. These challenges are mainly related to providing faster data communication over seamless, reliable and cost efficient wireless network, given the limited availability of physical radio resources, and taking into consideration the environmental impact caused by the increasing energy consumption. Traditional wireless communication is usually deployed in a cellular manner, where fixed base stations coordinate radio resources and play the role of an intermediate data handler. The concept of cellular networks and hotspots is widely adopted as the current stable scheme of wireless communication. However in many situations this fixed infrastructure could be impaired with severe damages caused by natural disasters, or could suffer congestions and traffic blockage. In addition to the fact that in the current networks any mobile-to-mobile data sessions should pass through the serving base station that might cause unnecessary energy consumption. In order to enhance the performance and reliability of future wireless networks and to reduce its environmental footprint, we explore two complementary concepts: the first is node cooperation and the second is aerial networks. With the ability of wireless nodes to cooperate lays two main possible opportunities; one is the ability of the direct delivery of information between the communicating nodes without relaying traffic through the serving base station, thus reducing energy consumption and alleviating traffic congestion. A second opportunity would be that one of the nodes helps a farther one by relaying its traffic towards the base station, thus extending network coverage and reliability. Both schemes can introduce significant energy saving and can enhance the overall availability of wireless networks in case of natural disasters. In addition to node cooperation, a complementary technology to explore is the \emph{aerial networks} where base stations are airborne on aerial platforms such as airships, UAVs or blimps. Aerial networks can provide a rapidly deployable coverage for remote areas or regions afflicted by natural disasters or even to patch surge traffic demand in public events. Where node cooperation can be implemented to complement both regular terrestrial coverage and to complement aerial networks. In this research, we explore these two complementary technologies, from both an experimental approach and from an analytic approach. From the experimental perspective we shed the light on the radio channel properties that is hosting terrestrial node cooperation and air-to-ground communication, namely we utilize both simulation results and practical measurements to formulate radio propagation models for device-to-device communication and for air-to-ground links. Furthermore we investigate radio spectrum availability for node cooperation in different urban environment, by conductive extensive mobile measurement survey. Within the experimental approach, we also investigate a novel concept of temporary cognitive femtocell network as an applied solution for public safety communication networks during the aftermath of a natural disaster. While from the analytical perspective, we utilize mathematical tools from stochastic geometry to formulate novel analytical methodologies, explaining some of the most important theoretical boundaries of the achievable enhancements in network performance promised by node cooperation. We start by determining the estimated coverage and rate received by mobile users from convectional cellular networks and from aerial platforms. After that we optimize this coverage and rate ensuring that relay nodes and users can fully exploit their coverage efficiently. We continue by analytically quantifying the cellular network performance during massive infrastructure failure, where some nodes play the role of low-power relays forming multi-hop communication links to assist farther nodes outside the reach of the healthy network coverage. In addition, we lay a mathematical framework for estimating the energy saving of a mediating relay assisting a pair of wireless devices, where we derive closed-form expressions for describing the geometrical zone where relaying is energy efficient. Furthermore, we introduce a novel analytic approach in analyzing the energy consumption of aerial-backhauled wireless nodes on ground fields through the assistance of an aerial base station, the novel mathematical framework is based on Mat\&#039;{e}rn hard-core point process. Then we shed the light on the points interacting of these point processes quantifying their main properties. Throughout this thesis we relay on verifying the analytic results and formulas against computer simulations using Monte-Carlo analysis. We also present practical numerical examples to reflect the usefulness of the presented methodologies and results in real life scenarios. Most of the work presented in this dissertation was published in-part or as a whole in highly ranked peer-reviewed journals, conference proceedings, book chapters, or otherwise currently undergoing a review process. These publications are highlighted and identified in the course of this thesis. Finally, we wish the reader to enjoy exploring the journey of this thesis, and hope it will add more understanding to the promising new technologies of aerial networks and node cooperation