Performance assessment of time–frequency RFI mitigation techniques in microwave radiometry

©2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.Radio–frequency interference (RFI) signals are a well-known threat for microwave radiometry (MWR) applications. In order to alleviate this problem, different approaches for RFI detection and mitigation are currently under development. Since RFI signals are man made, they tend to have their power more concentrated in the time–frequency (TF) space as compared to naturally emitted noise. The aim of this paper is to perform an assessment of different TF RFI mitigation techniques in terms of probability of detection, resolution loss (RL), and mitigation performance. In this assessment, six different kinds of RFI signals have been considered: a glitch, a burst of pulses, a wide-band chirp, a narrow-band chirp, a continuous wave, and a wide-band modulation. The results show that the best performance occurs when the transform basis has a similar shape as compared to the RFI signal. For the best case performance, the maximum residual RFI temperature is 14.8 K, and the worst RL is 8.4%. Moreover, the multiresolution Fourier transform technique appears as a good tradeoff solution among all other techniques since it can mitigate all RFI signals under evaluation with a maximum residual RFI temperature of 21 K, and a worst RL of 26.3%. Although the obtained results are still far from an acceptable bias Misplaced < 1 K for MWR applications, there is still work to do in a combined test using the information gathered simultaneously by all mitigation techniques, which could improve the overall performance of RFI mitigation.Peer ReviewedPostprint (author's final draft

A review of RFI mitigation techniques in microwave radiometry

Radio frequency interference (RFI) is a well-known problem in microwave radiometry (MWR). Any undesired signal overlapping the MWR protected frequency bands introduces a bias in the measurements, which can corrupt the retrieved geophysical parameters. This paper presents a literature review of RFI detection and mitigation techniques for microwave radiometry from space. The reviewed techniques are divided between real aperture and aperture synthesis. A discussion and assessment of the application of RFI mitigation techniques is presented for each type of radiometer.Peer ReviewedPostprint (published version

Analysis of RFI Identification and Mitigation in CAROLS Radiometer Data Using a Hardware Spectrum Analyser

A method to identify and mitigate radio frequency interference (RFI) in microwave radiometry based on the use of a spectrum analyzer has been developed. This method has been tested with CAROLS L-band airborne radiometer data that are strongly corrupted by RFI. RFI is a major limiting factor in passive microwave remote sensing interpretation. Although the 1.400–1.427 GHz bandwidth is protected, RFI sources close to these frequencies are still capable of corrupting radiometric measurements. In order to reduce the detrimental effects of RFI on brightness temperature measurements, a new spectrum analyzer has been added to the CAROLS radiometer system. A post processing algorithm is proposed, based on selective filters within the useful bandwidth divided into sub-bands. Two discriminant analyses based on the computation of kurtosis and Euclidian distances have been compared evaluated and validated in order to accurately separate the RF interference from natural signals

Real-Time Detection and Filtering of Radio Frequency Interference On-board a Spaceborne Microwave Radiometer: The CubeRRT Mission

The Cubesat Radiometer Radio frequency interference Technology validation mission (CubeRRT) was developed to demonstrate real-time on-board detection and filtering of radio frequency interference (RFI) for wide bandwidth microwave radiometers. CubeRRT’s key technology is its radiometer digital backend (RDB) that is capable of measuring an instantaneous bandwidth of 1 GHz and of filtering the input signal into an estimated total power with and without RFI contributions. CubeRRT’s on-board RFI processing capability dramatically reduces the volume of data that must be downlinked to the ground and eliminates the need for ground-based RFI processing. RFI detection is performed by resolving the input bandwidth into 128 frequency sub-channels, with the kurtosis of each sub-channel and the variations in power across frequency used to detect non-thermal contributions. RFI filtering is performed by removing corrupted frequency sub-channels prior to the computation of the total channel power. The 1 GHz bandwidth input signals processed by the RDB are obtained from the payload’s antenna (ANT) and radiometer front end (RFE) subsystems that are capable of tuning across RF center frequencies from 6 to 40 GHz. The CubeRRT payload was installed into a 6U spacecraft bus provided by Blue Canyon Technologies that provides spacecraft power, communications, data management, and navigation functions. The design, development, integration and test, and on-orbit operations of CubeRRT are described in this paper. The spacecraft was delivered on March 22nd, 2018 for launch to the International Space Station (ISS) on May 21st, 2018. Since its deployment from the ISS on July 13th, 2018, the CubeRRT RDB has completed more than 5000 hours of operation successfully, validating its robustness as an RFI processor. Although CubeRRT’s RFE subsystem ceased operating on September 8th, 2018, causing the RDB input thereafter to consist only of internally generated noise, CubeRRT’s key RDB technology continues to operate without issue and has demonstrated its capabilities as a valuable subsystem for future radiometry missions

An L-band Radio Frequency Interference (RFI) detection and mitigation testbed for microwave radiometry

Abstract—A microwave radiometer specifically designed to detect and mitigate many types of Radio Frequency Interference (RFI) is described. The L-band RFI Detection and Mitigation Testbed (DetMit Testbed) will not be optimized for radiometric observation as much as it is optimized for flexibility in the presence of RFI. While the DetMit Testbed will be a fully functional polarimetric L-band radiometer, the ultimate application of this instrument is not so much brightness measurements as it will be validation of RFI mitigation strategies for employment in future L-band (and other frequency) radiometers. The design approaches for the L-band RFI Detection and Mitigation Testbed are expected to apply to C-band and X-band, and presumably also to other frequencies of interest that experience RFI. Keywords-Detectors, digital radio, interference suppression, microwave radiometry. I

Impact of signal quantization on the performance of RFI mitigation algorithms

Radio Frequency Interference (RFI) is currently a major problem in Communications and Earth Observation, but it is even more dramatic in Microwave Radiometry because of the low power levels of the received signals. Its impact has been attested in several Earth Observation missions. On-board mitigation systems are becoming a requirement to detect and remove affected measurements, increasing thus radiometric accuracy and spatial coverage. However, RFI mitigation methods have not been tested yet in the context of some particular radiometer topologies, which rely on the use of coarsely quantized streams of data. In this study, the impact of quantization and sampling in the performance of several known RFI mitigation algorithms is studied under different conditions. It will be demonstrated that in the presence of clipping, quantization changes fundamentally the time-frequency properties of the contaminated signal, strongly impairing the performance of most mitigation methods. Important design considerations are derived from this analysis that must be taken into account when defining the architecture of future instruments. In particular, the use of Automatic Gain Control (AGC) systems is proposed, and its limitations are discussedPeer ReviewedPostprint (published version

A Demonstration of the Effects of Digitization on the Calculation of Kurtosis for the Detection of RFI in Microwave Radiometry

Abstract-Microwave radiometers detecting geophysical parameters are very susceptible to radio-frequency interference (RFI) from anthropogenic sources. RFI is always additive to a brightness observation, and so the presence of RFI can bias geophysical parameter retrieval. As microwave radiometers typically have the most sensitive receivers operating in their band, low-level RFI is both significant and difficult to identify. The kurtosis statistic can be a powerful means of identifying some types of low-level RFI, as thermal noise has a distinct kurtosis value of three, whereas thermal noise contaminated even with low-level nonthermal RFI often has other values of kurtosis. This paper derives some benign distortions of the kurtosis statistic due to digitization effects and demonstrates these effects with a laboratory experiment in which a known amount of low-level RFI is injected into a digital microwave radiometer