High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

Integrated radio frequency synthetizers for wireless applications

This thesis consists of six publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis concentrates on the design of phase-locked loop radio frequency synthesizers for wireless applications. In particular, the focus is on the implementation of the prescaler, the phase detector, and the chargepump. This work reviews the requirements set for the frequency synthesizer by the wireless standards, and how these requirements are derived from the system specifications. These requirements apply to both integer-N and fractional-N synthesizers. The work also introduces the special considerations related to the design of fractional-N phase-locked loops. Finally, implementation alternatives for the different building blocks of the synthesizer are reviewed. The presented work introduces new topologies for the phase detector and the chargepump, and improved topologies for high speed CMOS prescalers. The experimental results show that the presented topologies can be successfully used in both integer-N and fractional-N synthesizers with state-of-the-art performance. The last part of this work discusses the additional considerations that surface when the synthesizer is integrated into a larger system chip. It is shown experimentally that the synthesizer can be successfully integrated into a complex transceiver IC without sacrificing the performance of the synthesizer or the transceiver.reviewe

Multi-band OFDM UWB receiver with narrowband interference suppression

A multi band orthogonal frequency division multiplexing (MB-OFDM) compatible ultra wideband (UWB) receiver with narrowband interference (NBI) suppression capability is presented. The average transmit power of UWB system is limited to -41.3 dBm/MHz in order to not interfere existing narrowband systems. Moreover, it must operate even in the presence of unintentional radiation of FCC Class-B compatible devices. If this unintentional radiation resides in the UWB band, it can jam the communication. Since removing the interference in digital domain requires higher dynamic range of analog front-end than removing it in analog domain, a programmable analog notch filter is used to relax the receiver requirements in the presence of NBI. The baseband filter is placed before the variable gain amplifier (VGA) in order to reduce the signal swing at the VGA input. The frequency hopping period of MB-OFDM puts a lower limit on the settling time of the filter, which is inverse proportional to notch bandwidth. However, notch bandwidth should be low enough not to attenuate the adjacent OFDM tones. Since these requirements are contradictory, optimization is needed to maximize overall performance. Two different NBI suppression schemes are tested. In the first scheme, the notch filter is operating for all sub-bands. In the second scheme, the notch filter is turned on during the sub-band affected by NBI. Simulation results indicate that the UWB system with the first and the second suppression schemes can handle up to 6 dB and 14 dB more NBI power, respectively. The results of this work are not limited to MB-OFDM UWB system, and can be applied to other frequency hopping systems

Analysis and design of low power CMOS ultra wideband receiver

This research concentrates on the design and analysis of low power ultra wideband receivers for Multiband Orthogonal Frequency Division Multiplexing systems. Low power design entails different performance tradeoffs, which are analyzed. Relationship among power consumption, achievable noise figure and linearity performance including distortion products (cross-modulation, inter-modulation and harmonic distortion) are derived. From these relationships, circuit design proceeds with allocation of gain among different sub circuit blocks for power optimum system. A power optimum RF receiver front-end for MB-OFDM based UWB systems is designed that covers all the MB-OFDM spectrum between 3.1 GHZ to 9.6 GHZ. The receiver consists of a low-noise amplifier, down-converter, channel select filter and programmable gain amplifier and occupies only 1mm 2 in 0.13um CMOS process. Receiver consumes 20 mA from a 1.2 V supply and has the measured gain of 69db, noise figure less than 6 dB and input IIP 3 of -6 dBm

High Fidelity Satellite Navigation Receiver Front-End for Advanced Signal Quality Monitoring and Authentication

Over the last several years, interest in utilizing foreign satellite timing and navigation (satnav) signals to augment GPS has grown. Doing so is not without risks; foreign satnav signals must be vetted and determined to be trustworthy before use in military applications. Advanced signal quality monitoring methods can help to ensure that only authentic and reliable satnav signals are utilized. To effectively monitor and authenticate signals, the front-end must impress as little distortions upon the received signal as possible. The purpose of this study is to design, fabricate, and test the performance of a high-fidelity satnav receiver front-end for advanced monitoring of foreign and domestic space vehicle signals

OFDM para distribuição de dados de controlo em phased array antenas

Mestrado em Engenharia Eletrónica e TelecomunicaçõesCurrently, all the control data behind the RF front-end modules in phased array radars is transmitted digitally and simultaneously by means of optical ber, resulting in a massive distribution network. The design of cheaper radars requires alternative ways of transmission to be explored. An intuitive and rather straight approach is to take advantage of the already existent RF layer used for the distribution of the radar pulse. The aim of this thesis work is to investigate OFDM as a modulation option for that approach and to determine whether or not it is a viable one. As proof of concept, experimental results are presented and discussed.Actualmente, toda a informa cão de controlo por detráas dos móodulos T/R (Transmit/ Receive) em radares com phased arrays e transmitida digital e simultaneamente atrav és de fi bra optica, resultando numa rede de distribuiçaõ massiva. Para que se possa reduzir o custo de produção e limitações no design, e fundamental a exploração de alternativas para a transmissão destes dados. Uma ideia intuitiva e que não implica grandes modi ca ções estruturais, e tirar vantagem da j a existente layer de RF (R adio Frequência) usada para distribuição do pulso de radar pelos m ódulos. O objectivo desta tese é investigar OFDM (Orthogonal Frequency Division Multiplexing) como uma das opções para modulação do novo sinal de RF responsável pela informa ção de controlo e determinar se esta é ou não uma escolha vi ável. Como prova de conceito, resultados experimentais serão apresentados e discutidos

Multi-band OFDM UWB receiver with narrowband interference suppression

A multi band orthogonal frequency division multiplexing (MB-OFDM) compatible ultra wideband (UWB) receiver with narrowband interference (NBI) suppression capability is presented. The average transmit power of UWB system is limited to -41.3 dBm/MHz in order to not interfere existing narrowband systems. Moreover, it must operate even in the presence of unintentional radiation of FCC Class-B compatible devices. If this unintentional radiation resides in the UWB band, it can jam the communication. Since removing the interference in digital domain requires higher dynamic range of analog front-end than removing it in analog domain, a programmable analog notch filter is used to relax the receiver requirements in the presence of NBI. The baseband filter is placed before the variable gain amplifier (VGA) in order to reduce the signal swing at the VGA input. The frequency hopping period of MB-OFDM puts a lower limit on the settling time of the filter, which is inverse proportional to notch bandwidth. However, notch bandwidth should be low enough not to attenuate the adjacent OFDM tones. Since these requirements are contradictory, optimization is needed to maximize overall performance. Two different NBI suppression schemes are tested. In the first scheme, the notch filter is operating for all sub-bands. In the second scheme, the notch filter is turned on during the sub-band affected by NBI. Simulation results indicate that the UWB system with the first and the second suppression schemes can handle up to 6 dB and 14 dB more NBI power, respectively. The results of this work are not limited to MB-OFDM UWB system, and can be applied to other frequency hopping systems