36,668 research outputs found
Performance Comparison of Dual Connectivity and Hard Handover for LTE-5G Tight Integration in mmWave Cellular Networks
MmWave communications are expected to play a major role in the Fifth
generation of mobile networks. They offer a potential multi-gigabit throughput
and an ultra-low radio latency, but at the same time suffer from high isotropic
pathloss, and a coverage area much smaller than the one of LTE macrocells. In
order to address these issues, highly directional beamforming and a very
high-density deployment of mmWave base stations were proposed. This Thesis aims
to improve the reliability and performance of the 5G network by studying its
tight and seamless integration with the current LTE cellular network. In
particular, the LTE base stations can provide a coverage layer for 5G mobile
terminals, because they operate on microWave frequencies, which are less
sensitive to blockage and have a lower pathloss. This document is a copy of the
Master's Thesis carried out by Mr. Michele Polese under the supervision of Dr.
Marco Mezzavilla and Prof. Michele Zorzi. It will propose an LTE-5G tight
integration architecture, based on mobile terminals' dual connectivity to LTE
and 5G radio access networks, and will evaluate which are the new network
procedures that will be needed to support it. Moreover, this new architecture
will be implemented in the ns-3 simulator, and a thorough simulation campaign
will be conducted in order to evaluate its performance, with respect to the
baseline of handover between LTE and 5G.Comment: Master's Thesis carried out by Mr. Michele Polese under the
supervision of Dr. Marco Mezzavilla and Prof. Michele Zorz
TOPOLOGICAL PLANNING OF COMMUNICATION NETWORKS
In this paper, we concentrate on topological planning process of large-scale communication networks such as those used by telecom operators. Such networks are usually spread over large geographical area, and finding an optimal topology is very important part of the planning process. Network equipment used in such network is very expensive, and two connection points can be hundreds of kilometers apart. These networks, in most cases, form a backbone network of telecom operator, meaning that majority of traffic is carried through high-speed communication links of such network. Any cable cuts or equipment malfunctions could result in huge data losses. Therefore, such networks require high degree of availability and fault resistance, which must be considered during the planning process. Network topology providing fault resistance should offer at least two separate communication paths between any pair of network nodes. Most important issue in network topology planning is finding topology with lowest possible overall network price, while keeping all requirements (such as fault tolerance, availability, maximal number of hops, maximal blocking probability etc.) satisfied. Network design process can be divided into three stages. First step is making decisions about which network elements (nodes, existing edges) should be included in a backbone network (for instance, one of sub-problems appearing in this phase is facility location problem). Second step includes selection of network topology, so that all elements selected in first step will be interconnected satisfying given requirements. Last phase is used to determine node and link capacities needed for successful traffic transport as well as routings of traffic demands, including protection. Depending on technologies used in network, different routing and protection mechanisms, as well as specific topology models, can be used (e.g. SDH/WDM SHR, mesh, dual-homing etc.)
Separation Framework: An Enabler for Cooperative and D2D Communication for Future 5G Networks
Soaring capacity and coverage demands dictate that future cellular networks
need to soon migrate towards ultra-dense networks. However, network
densification comes with a host of challenges that include compromised energy
efficiency, complex interference management, cumbersome mobility management,
burdensome signaling overheads and higher backhaul costs. Interestingly, most
of the problems, that beleaguer network densification, stem from legacy
networks' one common feature i.e., tight coupling between the control and data
planes regardless of their degree of heterogeneity and cell density.
Consequently, in wake of 5G, control and data planes separation architecture
(SARC) has recently been conceived as a promising paradigm that has potential
to address most of aforementioned challenges. In this article, we review
various proposals that have been presented in literature so far to enable SARC.
More specifically, we analyze how and to what degree various SARC proposals
address the four main challenges in network densification namely: energy
efficiency, system level capacity maximization, interference management and
mobility management. We then focus on two salient features of future cellular
networks that have not yet been adapted in legacy networks at wide scale and
thus remain a hallmark of 5G, i.e., coordinated multipoint (CoMP), and
device-to-device (D2D) communications. After providing necessary background on
CoMP and D2D, we analyze how SARC can particularly act as a major enabler for
CoMP and D2D in context of 5G. This article thus serves as both a tutorial as
well as an up to date survey on SARC, CoMP and D2D. Most importantly, the
article provides an extensive outlook of challenges and opportunities that lie
at the crossroads of these three mutually entangled emerging technologies.Comment: 28 pages, 11 figures, IEEE Communications Surveys & Tutorials 201
An implementation of packet-switched communication for pilot protection at Tennessee Valley Authority
The utility network has long relied on Time Division Multiplexing (TDM) such as T1 and Synchronous Optical Network (SONET) as the main channel to transmit and receive data in a communication system. However, TDM technology is aging and its equipment becoming obsolete as vendors transition to Packet-Switched Networks (PSN) to make way for Ethernet-based network communications. Teleprotection is a critical element for a reliable power system as it provides high-speed tripping for faults on the protected line and is applied in various pilot protection schemes. Protection schemes cannot perform at their best without a fast and reliable communication system. The transition from a circuit-switched technology like SONET to a packet-based technology like Multiprotocol Label Switching-Transport Profile (MPLS-TP) has caused reservations for protection engineers as they express their concerns for lacking guaranteed 100% availability and potential latency. This paper will address this issue and the consistent test results at the Tennessee Valley Authority (TVA)\u27s lab have proven to satisfy the communication requirements in a teleprotection system. Teleprotection traffics make to its destination in order in microseconds, the symmetrical delay is less than 1µs, and especially the recovery from a failure occurs under 50ms (3 cycles). The results reassure the protection engineers that the Ethernet migration is necessary yet provides a better performance compared to the legacy system
- …