Design of ALU and Cache Memory for an 8 bit ALU

The design of an ALU and a Cache memory for use in a high performance processor was examined in this thesis. Advanced architectures employing increased parallelism were analyzed to minimize the number of execution cycles needed for 8 bit integer arithmetic operations. In addition to the arithmetic unit, an optimized SRAM memory cell was designed to be used as cache memory and as fast Look Up Table. The ALU consists of stand alone units for bit parallel computation of basic integer arithmetic operations. Addition and subtraction were performed using Kogge Stone parallel prefix hardware operating at 330MHz. A high performance multiplier was built using Radix 4 Modified Booth Encoder (MBE) and a Wallace Tree summation array. The multiplier requires single clock cycle for 8 bit integer multiplication and operates at a maximum frequency of 100MHz. Multiplicative division hardware was built for executing both integer division and square root. The division hardware computes 8-bit division and square root in 4 clock cycles. Multiplier forms the basic building block of all these functional units, making high level of resource sharing feasible with this architecture. The optimal operating frequency for the arithmetic unit is 70MHz. A 6T CMOS SRAM cell measuring 90 µm2 was designed using minimum size transistors. The layout allows for horizontal overlap resulting in effective area of 76 µm2 for an 8x8 array. By substituting equivalent bit line capacitance of P4 L1 Cache, the memory was simulated to have a read time of 3.27ns. An optimized set of test vectors were identified to enable high fault coverage without the need for any additional test circuitry. Sixteen test cases were identified that would toggle all the nodes and provide all possible inputs to the sub units of the multiplier. A correlation based semi automatic method was investigated to facilitate test case identification for large multipliers. This method of testability eliminates performance and area overhead associated with conventional testability hardware. Bottom up design methodology was employed for the design. The performance and area metrics are presented along with estimated power consumption. A set of Monte Carlo analysis was carried out to ensure the dependability of the design under process variations as well as fluctuations in operating conditions. The arithmetic unit was found to require a total die area of 2mm2 (approx.) in 0.35 micron process

On The Design Of Low-Complexity High-Speed Arithmetic Circuits In Quantum-Dot Cellular Automata Nanotechnology

For the last four decades, the implementation of very large-scale integrated systems has largely based on complementary metal-oxide semiconductor (CMOS) technology. However, this technology has reached its physical limitations. Emerging nanoscale technologies such as quantum-dot cellular automata (QCA), single electron tunneling (SET), and tunneling phase logic (TPL) are major candidate for possible replacements of CMOS. These nanotechnologies use majority and/or minority logic and inverters as circuit primitives. In this dissertation, a comprehensive methodology for majority/minority logic networks synthesis is developed. This method is capable of processing any arbitrary multi-output Boolean function to nd its equivalent optimal majority logic network targeting to optimize either the number of gates or levels. The proposed method results in different primary equivalent majority expression networks. However, the most optimized network will be generated as a nal solution. The obtained results for 15 MCNC benchmark circuits show that when the number of majority gates is the rst optimization priority, there is an average reduction of 45.3% in the number of gates and 15.1% in the number of levels. They also show that when the rst priority is the number of levels, an average reduction of 23.5% in the number of levels and 43.1% in the number of gates is possible, compared to the majority AND/OR mapping method. These results are better compared to those obtained from the best existing methods. In this dissertation, our approach is to exploit QCA technology because of its capability to implement high-density, very high-speed switching and tremendously lowpower integrated systems and is more amenable to digital circuits design. In particular, we have developed algorithms for the QCA designs of various single- and multi-operation arithmetic arrays. Even though, majority/minority logic are the basic units in promising nanotechnologies, an XOR function can be constructed in QCA as a single device. The basic cells of the proposed arrays are developed based on the fundamental logic devices in QCA and a single-layer structure of the three-input XOR function. This process leads to QCA arithmetic circuits with better results in view of dierent aspects such as cell count, area, and latency, compared to their best counterparts. The proposed arrays can be formed in a pipeline manner to perform the arithmetic operations for any number of bits which could be quite valuable while considering the future design of large-scale QCA circuits

16-bit Digital Adder Design in 250nm and 64-bit Digital Comparator Design in 90nm CMOS Technologies

High speed, low power, and area efficient adders and comparators continue to play a key role in hardware implementation of digital signal processing applications. Adders based on Complimentary Pass Transistor Logic (CPL) are power and area efficient, but are slower compared to Square Root Carry Select (SQRT-CS) based adders. This thesis demonstrates a unique custom designed 16-bit adder in 250-nm CMOS technology to obtain fast and power/area efficient features by combining CPL and CS logic. Comparing the results obtained for proposed 16-bit Linear CPL/CS adder with the BEC (Binary Excess-1 Code) based low power SQRT-CS adder, the delay is reduced by approximately one thirds, power is reduced by 19.2%, and the number of transistors is reduced by 23.4%. Also, new tree-based 64-bit static and dynamic digital comparators are presented in this thesis to perform high speed and low power operations. This tree-based architecture combines a new approach of designing dynamic comparator using a low duty cycle clock to reduce the short circuit power consumption in pre-charge (or pre-discharge) mode. This work also introduces a new sizing strategy and load balancing techniques to improve self-pipelining tendency of a tree based design. A resource sharing technique is also integrated in both static and dynamic comparator designs. At 1.2V power supply in CMOS 90nm technology, worst path delay and worst power are 374ps and 822µW, respectively for low cost static design with 1244 (768+476) transistors in total. 768 transistors are used for resource sharing. The proposed full and partially dynamic designs show superior power efficiency compared to recent state of art designs. The worst power consumptions at 5GHz and 25% (50ps) duty cycle clock for the 64-bit full and partially dynamic comparator designs are 5.00mW and 2.78mW, respectively. 769 (320+449) transistors includes 320 transistors for resource sharing, and 1217 (768+449) includes 768 transistors for resource sharing for full and partial dynamic comparators, respectively

MFPA: Mixed-Signal Field Programmable Array for Energy-Aware Compressive Signal Processing

Compressive Sensing (CS) is a signal processing technique which reduces the number of samples taken per frame to decrease energy, storage, and data transmission overheads, as well as reducing time taken for data acquisition in time-critical applications. The tradeoff in such an approach is increased complexity of signal reconstruction. While several algorithms have been developed for CS signal reconstruction, hardware implementation of these algorithms is still an area of active research. Prior work has sought to utilize parallelism available in reconstruction algorithms to minimize hardware overheads; however, such approaches are limited by the underlying limitations in CMOS technology. Herein, the MFPA (Mixed-signal Field Programmable Array) approach is presented as a hybrid spin-CMOS reconfigurable fabric specifically designed for implementation of CS data sampling and signal reconstruction. The resulting fabric consists of 1) slice-organized analog blocks providing amplifiers, transistors, capacitors, and Magnetic Tunnel Junctions (MTJs) which are configurable to achieving square/square root operations required for calculating vector norms, 2) digital functional blocks which feature 6-input clockless lookup tables for computation of matrix inverse, and 3) an MRAM-based nonvolatile crossbar array for carrying out low-energy matrix-vector multiplication operations. The various functional blocks are connected via a global interconnect and spin-based analog-to-digital converters. Simulation results demonstrate significant energy and area benefits compared to equivalent CMOS digital implementations for each of the functional blocks used: this includes an 80% reduction in energy and 97% reduction in transistor count for the nonvolatile crossbar array, 80% standby power reduction and 25% reduced area footprint for the clockless lookup tables, and roughly 97% reduction in transistor count for a multiplier built using components from the analog blocks. Moreover, the proposed fabric yields 77% energy reduction compared to CMOS when used to implement CS reconstruction, in addition to latency improvements

Algorithms and architectures for decimal transcendental function computation

Nowadays, there are many commercial demands for decimal floating-point (DFP) arithmetic operations such as financial analysis, tax calculation, currency conversion, Internet based applications, and e-commerce. This trend gives rise to further development on DFP arithmetic units which can perform accurate computations with exact decimal operands. Due to the significance of DFP arithmetic, the IEEE 754-2008 standard for floating-point arithmetic includes it in its specifications. The basic decimal arithmetic unit, such as decimal adder, subtracter, multiplier, divider or square-root unit, as a main part of a decimal microprocessor, is attracting more and more researchers' attentions. Recently, the decimal-encoded formats and DFP arithmetic units have been implemented in IBM's system z900, POWER6, and z10 microprocessors. Increasing chip densities and transistor count provide more room for designers to add more essential functions on application domains into upcoming microprocessors. Decimal transcendental functions, such as DFP logarithm, antilogarithm, exponential, reciprocal and trigonometric, etc, as useful arithmetic operations in many areas of science and engineering, has been specified as the recommended arithmetic in the IEEE 754-2008 standard. Thus, virtually all the computing systems that are compliant with the IEEE 754-2008 standard could include a DFP mathematical library providing transcendental function computation. Based on the development of basic decimal arithmetic units, more complex DFP transcendental arithmetic will be the next building blocks in microprocessors. In this dissertation, we researched and developed several new decimal algorithms and architectures for the DFP transcendental function computation. These designs are composed of several different methods: 1) the decimal transcendental function computation based on the table-based first-order polynomial approximation method; 2) DFP logarithmic and antilogarithmic converters based on the decimal digit-recurrence algorithm with selection by rounding; 3) a decimal reciprocal unit using the efficient table look-up based on Newton-Raphson iterations; and 4) a first radix-100 division unit based on the non-restoring algorithm with pre-scaling method. Most decimal algorithms and architectures for the DFP transcendental function computation developed in this dissertation have been the first attempt to analyze and implement the DFP transcendental arithmetic in order to achieve faithful results of DFP operands, specified in IEEE 754-2008. To help researchers evaluate the hardware performance of DFP transcendental arithmetic units, the proposed architectures based on the different methods are modeled, verified and synthesized using FPGAs or with CMOS standard cells libraries in ASIC. Some of implementation results are compared with those of the binary radix-16 logarithmic and exponential converters; recent developed high performance decimal CORDIC based architecture; and Intel's DFP transcendental function computation software library. The comparison results show that the proposed architectures have significant speed-up in contrast to the above designs in terms of the latency. The algorithms and architectures developed in this dissertation provide a useful starting point for future hardware-oriented DFP transcendental function computation researches

In-Memory Computing by Using Nano-ionic Memristive Devices

By reaching to the CMOS scaling limitation based on the Moore’s law and due to the increasing disparity between the processing units and memory performance, the quest is continued to find a suitable alternative to replace the conventional technology. The recently discovered two terminal element, memristor, is believed to be one of the most promising candidates for future very large scale integrated systems. This thesis is comprised of two main parts, (Part I) modeling the memristor devices, and (Part II) memristive computing. The first part is presented in one chapter and the second part of the thesis contains five chapters. The basics and fundamentals regarding the memristor functionality and memristive computing are presented in the introduction chapter. A brief detail of these two main parts is as follows: Part I: Modeling- This part presents an accurate model based on the charge transport mechanisms for nanoionic memristor devices. The main current mechanism in metal/insulator/metal (MIM) structures are assessed, a physic-based model is proposed and a SPICE model is presented and tested for four different fabricated devices. An accuracy comparison is done for various models for Ag/TiO2/ITO fabricated device. Also, the functionality of the model is tested for various input signals. Part II: Memristive computing- Memristive computing is about utilizing memristor to perform computational tasks. This part of the thesis is divided into neuromorphic, analog and digital computing schemes with memristor devices. – Neuromorphic computing- Two chapters of this thesis are about biologicalinspired memristive neural networks using STDP-based learning mechanism. The memristive implementation of two well-known spiking neuron models, Hudgkin-Huxley and Morris-Lecar, are assessed and utilized in the proposed memristive network. The synaptic connections are also memristor devices in this design. Unsupervised pattern classification tasks are done to ensure the right functionality of the system. – Analog computing- Memristor has analog memory property as it can be programmed to different memristance values. A novel memristive analog adder is designed by Continuous Valued Number System (CVNS) scheme and its circuit is comprised of addition and modulo blocks. The proposed analog adder design is explained and its functionality is tested for various numbers. It is shown that the CVNS scheme is compatible with memristive design and the environment resolution can be adjusted by the memristance ratio of the memristor devices. – Digital computing- Two chapters are dedicated for digital computing. In the first one, a development over IMPLY-based logic with memristor is provided to implement a 4:2 compressor circuit. In the second chapter, A novel resistive over a novel mirrored memristive crossbar platform. Different logic gates are designed with the proposed memristive logic method and the simulations are provided with Cadence to prove the functionality of the logic. The logic implementation over a mirrored memristive crossbars is also assessed

Design automation of approximate circuits with runtime reconfigurable accuracy

Leveraging the inherent error tolerance of a vast number of application domains that are rapidly growing, approximate computing arises as a design alternative to improve the efficiency of our computing systems by trading accuracy for energy savings. However, the requirement for computational accuracy is not fixed. Controlling the applied level of approximation dynamically at runtime is a key to effectively optimize energy, while still containing and bounding the induced errors at runtime. In this paper, we propose and implement an automatic and circuit independent design framework that generates approximate circuits with dynamically reconfigurable accuracy at runtime. The generated circuits feature varying accuracy levels, supporting also accurate execution. Extensive experimental evaluation, using industry strength flow and circuits, demonstrates that our generated approximate circuits improve the energy by up to 41% for 2% error bound and by 17.5% on average under a pessimistic scenario that assumes full accuracy requirement in the 33% of the runtime. To demonstrate further the efficiency of our framework, we considered two state-of-the-art technology libraries which are a 7nm conventional FinFET and an emerging technology that boosts performance at a high cost of increased dynamic power

High sample-rate Givens rotations for recursive least squares

The design of an application-specific integrated circuit of a parallel array processor is considered for recursive least squares by QR decomposition using Givens rotations, applicable in adaptive filtering and beamforming applications. Emphasis is on high sample-rate operation, which, for this recursive algorithm, means that the time to perform arithmetic operations is critical. The algorithm, architecture and arithmetic are considered in a single integrated design procedure to achieve optimum results. A realisation approach using standard arithmetic operators, add, multiply and divide is adopted. The design of high-throughput operators with low delay is addressed for fixed- and floating-point number formats, and the application of redundant arithmetic considered. New redundant multiplier architectures are presented enabling reductions in area of up to 25%, whilst maintaining low delay. A technique is presented enabling the use of a conventional tree multiplier in recursive applications, allowing savings in area and delay. Two new divider architectures are presented showing benefits compared with the radix-2 modified SRT algorithm. Givens rotation algorithms are examined to determine their suitability for VLSI implementation. A novel algorithm, based on the Squared Givens Rotation (SGR) algorithm, is developed enabling the sample-rate to be increased by a factor of approximately 6 and offering area reductions up to a factor of 2 over previous approaches. An estimated sample-rate of 136 MHz could be achieved using a standard cell approach and O.35pm CMOS technology. The enhanced SGR algorithm has been compared with a CORDIC approach and shown to benefit by a factor of 3 in area and over 11 in sample-rate. When compared with a recent implementation on a parallel array of general purpose (GP) DSP chips, it is estimated that a single application specific chip could offer up to 1,500 times the computation obtained from a single OP DSP chip