Digital Predistortion of Millimeter-Wave Phased Antenna Arrays

The cost of deployment of reliable, high-throughput, fifth-generation (5G) millimeter-wave (mm-wave) base stations will depend significantly on the maximum equivalent isotropically radiated power (EIRP) that the base stations can transmit. High EIRP can be generated using active beamforming antenna arrays with large apertures and driven by an array of power amplifiers (PAs). However, given the tight half-wavelength lattice that the arrays must retain to ensure a wide beam steering range, the achievable EIRP quickly becomes thermally-limited. Efficient power amplification is thus imperative to low-cost and reliable beamforming antenna array design. This work considers the application of Digital Predistortion (DPD) as an efficiency-enhancement technique for mm-wave beamforming antenna arrays. Two RF beamforming configurations were considered and corresponding DPD schemes were investigated. First, a single-input single-output (SISO) DPD is proposed that can linearize a single-user RF beamforming array in the presence of non-idealities such as PA load modulation and variation of phase shifter gain with phase. The SISO DPD relies on a feedback signal which reflects a coherent summation of the PA outputs. The SISO DPD is then validated by measurement of a 4-element and 64-element array at 28 GHz with 800 MHz modulated signals using a single over-the-air feedback signal. The SISO DPD uses different sets of coefficients to cope with changes in both linear and non-linear distortions as the beam is steered. Second, the SISO DPD formulation is extended to multi-user RF beamforming to linearize multiple sub-arrays. In this configuration, non-negligible inter-user interference can affect the DPD training. To address the interference, a linear estimate of the interference is calculated and canceled for each user before extracting the SISO DPD coefficients in each sub-array. The SISO DPD with interference cancellation is validated by measurement of a 2-user 2x64-element subarray hybrid at 28 GHz with 800 MHz modulated signals across different combinations of steering angles for the two users

Array Architectures and Physical Layer Design for Millimeter-Wave Communications Beyond 5G

Ever increasing demands in mobile data rates have resulted in exploration of millimeter-wave (mmW) frequencies for the next generation (5G) wireless networks. Communications at mmW frequencies is presented with two keys challenges. Firstly, high propagation loss requires base stations (BSs) and user equipment (UEs) to use a large number of antennas and narrow beams to close the link with sufficient received signal power. Consequently, communications using narrow beams create a new challenge in channel estimation and link establishment based on fine angular probing. Current mmW system use analog phased arrays that can probe only one angle at the time which results in high latency during link establishment and channel tracking. It is desirable to design low latency beam training by exploring both physical layer designs and array architectures that could replace current 5G approaches and pave the way to the communications for frequency bands in higher mmW band and sub-THz region where larger antenna arrays and communications bandwidth can be exploited. To this end, we propose a novel signal processing techniques exploiting unique properties of mmW channel, and show both theoretically, in simulation and experiments its advantages over conventional approaches. Secondly, we explore different array architecture design and analyze their trade-offs between spectral efficiency and power consumption and area. For comprehensive comparison, we have developed a methodology for optimal design of system parameters for different array architecture candidates based on the spectral efficiency target, and use these parameters to estimate the array area and power consumption based on the circuits reported in the literature. We show that the hybrid analog and digital architectures have severe scalability concerns in radio frequency signal distribution with increased array size and spatial multiplexing levels, while the fully-digital array architectures have the best performance and power/area trade-offs.The developed approaches are based on a cross-disciplinary research that combines innovation in model based signal processing, machine learning, and radio hardware. This work is the first to apply compressive sensing (CS), a signal processing tool that exploits sparsity of mmW channel model, to accelerate beam training of mmW cellular system. The algorithm is designed to address practical issues including the requirement of cell discovery and synchronization that involves estimation of angular channel together with carrier frequency offset and timing offsets. We have analyzed the algorithm performance in the 5G compliant simulation and showed that an order of magnitude saving is achieved in initial access latency for the desired channel estimation accuracy. Moreover, we are the first to develop and implement a neural network assisted compressive beam alignment to deal with hardware impairments in mmW radios. We have used 60GHz mmW testbed to perform experiments and show that neural networks approach enhances alignment rate compared to CS. To further accelerate beam training, we proposed a novel frequency selective probing beams using the true-time-delay (TTD) analog array architecture. Our approach utilizes different subcarriers to scan different directions, and achieves a single-shot beam alignment, the fastest approach reported to date. Our comprehensive analysis of different array architectures and exploration of emerging architectures enabled us to develop an order of magnitude faster and energy efficient approaches for initial access and channel estimation in mmW systems

Massive Multi-Antenna Communications with Low-Resolution Data Converters

Massive multi-user (MU) multiple-input multiple-output (MIMO) will be a core technology in future cellular communication systems. In massive MU-MIMO systems, the number of antennas at the base station (BS) is scaled up by several orders of magnitude compared to traditional multi-antenna systems with the goals of enabling large gains in capacity and energy efficiency. However, scaling up the number of active antenna elements at the BS will lead to significant increases in power consumption and system costs unless power-efficient and low-cost hardware components are used. In this thesis, we investigate the performance of massive MU-MIMO systems for the case when the BS is equipped with low-resolution data converters.First, we consider the massive MU-MIMO uplink for the case when the BS uses low-resolution analog-to-digital converters (ADCs) to convert the received signal into the digital domain. Our focus is on the case where neither the transmitter nor the receiver have any a priori channel state information (CSI), which implies that the channel realizations have to be learned through pilot transmission followed by BS-side channel estimation, based on coarsely quantized observations. We derive a low-complexity channel estimator and present lower bounds and closed-form approximations for the information-theoretic rates achievable with the proposed channel estimator together with conventional linear detection algorithms. Second, we consider the massive MU-MIMO downlink for the case when the BS uses low-resolution digital-to-analog converters (DACs) to generate the transmit signal. We derive lower bounds and closed-form approximations for the achievable rates with linear precoding under the assumption that the BS has access to perfect CSI. We also propose novel nonlinear precoding algorithms that are shown to significantly outperform linear precoding for the extreme case of 1-bit DACs. Specifically, for the case of symbol-rate 1-bit DACs and frequency-flat channels, we develop a multitude of nonlinear precoders that trade between performance and complexity. We then extend the most promising nonlinear precoders to the case of oversampling 1-bit DACs and orthogonal frequency-division multiplexing for operation over frequency-selective channels.Third, we extend our analysis to take into account other hardware imperfections such as nonlinear amplifiers and local oscillators with phase noise.The results in this thesis suggest that the resolution of the ADCs and DACs in massive MU-MIMO systems can be reduced significantly compared to what is used in today\u27s state-of-the-art communication systems, without significantly reducing the overall system performance

Modeling and Linearization of MIMO RF Transmitters

Multiple-input multiple-output (MIMO) technology will continue to play a vital role in next-generation wireless systems, e.g., the fifth-generation wireless networks (5G). Large-scale antenna arrays (also called massive MIMO) seem to be the most promising physical layer solution for meeting the ever-growing demand for high spectral efficiency. Large-scale MIMO arrays are typically deployed with high integration and using low-cost components. Hence, they are prone to different hardware impairments such as crosstalk between the transmit antennas and power amplifier (PA) nonlinearities, which distort the transmitted signal. To avert the performance degradation due to these impairments, it is essential to have mechanisms for predicting the output of the MIMO arrays. Such prediction mechanisms are mandatory for performance evaluation and, more importantly, for the adoption of proper compensation techniques such as digital predistortion (DPD) schemes. This has stirred a considerable amount of interest among researchers to develop new hardware and signal processing solutions to address the requirements of large-scale MIMO systems. In the context of MIMO systems, one particular problem is that the hardware cost and complexity scale up with the increase of the size of the MIMO system. As a result, the MIMO systems tend to be implemented on a chip and are very compact. Reduction of the cost by reducing the bill of material is possible when several components are eliminated. The reuse of already existing hardware is an alternative solution. As a result, such systems are prone to excessive sources of distortion, such as crosstalk. Accordingly, crosstalk in MIMO systems in its simplest form can affect the DPD coefficient estimation scheme. In this thesis, the effect of crosstalk on two main DPD estimation techniques, know as direct learning algorithm (DLA) and indirect learning algorithm (ILA), is studied. The PA behavioral modeling and DPD scheme face several challenges that seek cost-efficient and flexible solutions too. These techniques require constant capture of the PA output feedback signal, which ultimately requires the implementation of a complete transmitter observation receiver (TOR) chain for the individual transmit path. In this thesis, a technique to reuse the receiver path of the MIMO TDD transceiver as a TOR is developed, which is based on over-the-air (OTA) measurements. With these techniques, individual PA behavioral modeling and DPD can be done by utilizing a few receivers of the MIMO TDD system. To use OTA measurements, an on-site antenna calibration scheme is developed to individually estimate the coupling between the transmitter and the receiver antennas. Furthermore, a digital predistortion technique for compensating the nonlinearity of several PAs in phased arrays is presented. The phased array can be a subset of massive MIMO systems, and it uses several antennas to steer the transmitted signal in a particular direction by appropriately assigning the magnitude and the phase of the transmitted signal from each antenna. The particular structure of phased arrays requires the linearization of several PAs with a single DPD. By increasing the number of RF branches and consequently increasing the number of PAs in the phased array, the linearization task becomes challenging. The DPD must be optimized to results in the best overall linear performance of the phased array in the field. The problem of optimized DPD for phased array has not been addressed appropriately in the literature. In this thesis, a DPD technique is developed based on an optimization problem to address the linearization of PAs with high variations. The technique continuously optimizes the DPD coefficients through several iterations considering the effect of each PA simultaneously. Therefore, it results in the best optimized DPD performance for several PAs. Extensive analysis, simulations, and measurement evaluation is carried out as a proof of concept. The different proposed techniques are compared with conventional approaches, and the results are presented. The techniques proposed in this thesis enable cost-efficient and flexible signal processing approaches to facilitate the development of future wireless communication systems

Advanced Symbol-level Precoding Schemes for Interference Exploitation in Multi-antenna Multi-user Wireless Communications

The utilization of multi-antenna transmitters relying on full frequency reuse has proven to be an effective strategy towards fulfilling the constantly increasing throughput requirements of wireless communication systems. As a consequence, in the last two decades precoding has been a prolific research area, due to its ability to handle the interference arising among simultaneous transmissions addressed to different co-channel users. The conventional precoding strategies aim at mitigating the multi-user interference (MUI) by exploiting the knowledge of the channel state information (CSI). More recently, novel approaches have been proposed where the aim is not to eliminate the interference, but rather to control it so as to achieve a constructive interference effect at each receiver. In these schemes, referred to as symbol-level precoding (SLP), the data information (data symbols) is used together with the CSI in the precoding design, which can be addressed following several optimization strategies. In the context of SLP, the work carried out in this thesis is mainly focused on developing more advanced optimization strategies suitable to non-linear systems, where the per-antenna high-power amplifiers introduce an amplitude and phase distortion on the transmitted signals. More specifically, the main objective is to exploit the potential of SLP not only to achieve the constructive interference at the receivers, but also to control the per-antenna instantaneous transmit power, improving the power dynamics of the transmitted waveforms. In fact, a reduction of the power variation of the signals, both in the spatial dimension (across the different antennas) and in the temporal dimension, is particularly important for mitigating the non-linear effects. After a detailed review of the state of the art of SLP, the first part of the thesis is focused on improving the power dynamics of the transmitted signals in the spatial dimension, by reducing the instantaneous power imbalances across the different antennas. First, a SLP per-antenna power minimization scheme is presented, followed by a related max-min fair formulation with per-antenna power constraints. These approaches allow to reduce the power peaks of the signals across the antennas. Next, more advanced SLP schemes are formulated and solved, with the objective of further improving the spatial dynamics of the signals. Specifically, a first approach performs a peak power minimization under a lower bound constraint on the per-antenna transmit power, while a second strategy minimizes the spatial peak-to-average power ratio. The second part of this thesis is devoted to developing a novel SLP method, referred to as spatio-temporal SLP, where the temporal variation of the transmit power is also considered in the SLP optimization. This new model allows to minimize the peak-to-average power ratio of the transmitted waveforms both in the spatial and in the temporal dimensions, thus further improving the robustness of the signals to non-linear effects. Then, this thesis takes one step further, by exploiting the developed spatio-temporal SLP model in a different context. In particular, a spatio-temporal SLP scheme is proposed which enables faster-than-Nyquist (FTN) signaling over multi-user systems, by constructively handling at the transmitter side not only the MUI but also the inter-symbol interference (ISI). This strategy allows to benefit from the increased throughput provided by FTN signaling without imposing additional complexity at the user terminals. Extensive numerical results are presented throughout the thesis, in order to assess the performance of the proposed schemes with respect to the state of the art in SLP. The thesis concludes summarizing the main research findings and identifying the open problems, which will constitute the basis for the future work

Baseband Processing for 5G and Beyond: Algorithms, VLSI Architectures, and Co-design

In recent years the number of connected devices and the demand for high data-rates have been significantly increased. This enormous growth is more pronounced by the introduction of the Internet of things (IoT) in which several devices are interconnected to exchange data for various applications like smart homes and smart cities. Moreover, new applications such as eHealth, autonomous vehicles, and connected ambulances set new demands on the reliability, latency, and data-rate of wireless communication systems, pushing forward technology developments. Massive multiple-input multiple-output (MIMO) is a technology, which is employed in the 5G standard, offering the benefits to fulfill these requirements. In massive MIMO systems, base station (BS) is equipped with a very large number of antennas, serving several users equipments (UEs) simultaneously in the same time and frequency resource. The high spatial multiplexing in massive MIMO systems, improves the data rate, energy and spectral efficiencies as well as the link reliability of wireless communication systems. The link reliability can be further improved by employing channel coding technique. Spatially coupled serially concatenated codes (SC-SCCs) are promising channel coding schemes, which can meet the high-reliability demands of wireless communication systems beyond 5G (B5G). Given the close-to-capacity error correction performance and the potential to implement a high-throughput decoder, this class of code can be a good candidate for wireless systems B5G. In order to achieve the above-mentioned advantages, sophisticated algorithms are required, which impose challenges on the baseband signal processing. In case of massive MIMO systems, the processing is much more computationally intensive and the size of required memory to store channel data is increased significantly compared to conventional MIMO systems, which are due to the large size of the channel state information (CSI) matrix. In addition to the high computational complexity, meeting latency requirements is also crucial. Similarly, the decoding-performance gain of SC-SCCs also do come at the expense of increased implementation complexity. Moreover, selecting the proper choice of design parameters, decoding algorithm, and architecture will be challenging, since spatial coupling provides new degrees of freedom in code design, and therefore the design space becomes huge. The focus of this thesis is to perform co-optimization in different design levels to address the aforementioned challenges/requirements. To this end, we employ system-level characteristics to develop efficient algorithms and architectures for the following functional blocks of digital baseband processing. First, we present a fast Fourier transform (FFT), an inverse FFT (IFFT), and corresponding reordering scheme, which can significantly reduce the latency of orthogonal frequency-division multiplexing (OFDM) demodulation and modulation as well as the size of reordering memory. The corresponding VLSI architectures along with the application specific integrated circuit (ASIC) implementation results in a 28 nm CMOS technology are introduced. In case of a 2048-point FFT/IFFT, the proposed design leads to 42% reduction in the latency and size of reordering memory. Second, we propose a low-complexity massive MIMO detection scheme. The key idea is to exploit channel sparsity to reduce the size of CSI matrix and eventually perform linear detection followed by a non-linear post-processing in angular domain using the compressed CSI matrix. The VLSI architecture for a massive MIMO with 128 BS antennas and 16 UEs along with the synthesis results in a 28 nm technology are presented. As a result, the proposed scheme reduces the complexity and required memory by 35%–73% compared to traditional detectors while it has better detection performance. Finally, we perform a comprehensive design space exploration for the SC-SCCs to investigate the effect of different design parameters on decoding performance, latency, complexity, and hardware cost. Then, we develop different decoding algorithms for the SC-SCCs and discuss the associated decoding performance and complexity. Also, several high-level VLSI architectures along with the corresponding synthesis results in a 12 nm process are presented, and various design tradeoffs are provided for these decoding schemes

I/Q Imbalance in Multiantenna Systems: Modeling, Analysis and RF-Aware Digital Beamforming

Wireless communications has experienced an unprecedented increase in data rates, numbers of active devices and selection of applications during recent years. However, this is expected to be just a start for future developments where a wireless connection is seen as a fundamental resource for almost any electrical device, no matter where and when it is operating. Since current radio technologies cannot provide such services with reasonable costs or even at all, a multitude of technological developments will be needed. One of the most important subjects, in addition to higher bandwidths and flexible network functionalities, is the exploitation of multiple antennas in base stations (BSs) as well as in user equipment (UEs). That kind of multiantenna communications can boost the capacity of an individual UE-BS link through spatial antenna multiplexing and increase the quality as well as robustness of the link via antenna diversity. Multiantenna technologies provide improvements also on the network level through spatial UE multiplexing and sophisticated interference management. Additionally, multiple antennas can provide savings in terms of the dissipated power since transmission and reception can be steered more efficiently in space, and thus power leakage to other directions is decreased. However, several issues need to be considered in order to get multiantenna technologies widely spread. First, antennas and the associated transceiver chains are required to be simple and implementable with low costs. Second, size of the antennas and transceivers need to be minimized. Finally, power consumption of the system must be kept under control. The importance of these requirements is even emphasized when considering massive multiple-input multiple-output (MIMO) systems consisting of devices equipped with tens or even hundreds of antennas.In this thesis, we consider multiantenna devices where the associated transceiver chains are implemented in such a way that the requirements above can be met. In particular, we focus on the direct-conversion transceiver principle which is seen as a promising radio architecture for multiantenna systems due to its low costs, small size, low power consumption and good flexibility. Whereas these aspects are very promising, direct-conversion transceivers have also some disadvantages and are vulnerable to certain imperfections in the analog radio frequency (RF) electronics in particular. Since the effects of these imperfections usually get even worse when optimizing costs of the devices, the scope of the thesis is on the effects and mitigation of one of the most severe RF imperfection, namely in-phase/quadrature (I/Q) imbalance.Contributions of the thesis can be split into two main themes. First of them is multiantenna narrowband beamforming under transmitter (TX) and receiver (RX) I/Q imbalances. We start by creating a model for the signals at the TX and RX, both under I/Q imbalances. Based on these models we derive analytical expressions for the antenna array radiation patterns and notice that I/Q imbalance distorts not only the signals but also the radiation characteristics of the array. After that, stemming from the nature of the distortion, we utilize widely-linear (WL) processing, where the signals and their complex conjugates are processed jointly, for the beamforming task under I/Q imbalance. Such WL processing with different kind of statistical and adaptive beamforming algorithms is finally shown to provide a flexible operation as well as distortion-free signals and radiation patterns when being under various I/Q imbalance schemes.The second theme extends the work to wideband systems utilizing orthogonal frequency-division multiplexing (OFDM)-based waveforms. The focus is on uplink communications and BS RX processing in a multiuser MIMO (MU-MIMO) scheme where spatial UE multiplexing is applied and further UE multiplexing takes place in frequency domain through the orthogonal frequency-division multiple access (OFDMA) principle. Moreover, we include the effects of external co-channel interference into our analysis in order to model the challenges in heterogeneous networks. We formulate a flexible signal model for a generic uplink scheme where I/Q imbalance occurs on both TX and RX sides. Based on the model, we analyze the signal distortion in frequency domain and develop augmented RX processing methods which process signals at mirror subcarrier pairs jointly. Additionally, the proposed augmented methods are numerically shown to outperform corresponding per-subcarrier method in terms of the instantaneous signal-to-interference-and-noise ratio (SINR). Finally, we address some practical aspects and conclude that the augmented processing principle is a promising tool for RX processing in multiantenna wideband systems under I/Q imbalance.The thesis provides important insight for development of future radio networks. In particular, the results can be used as such for implementing digital signal processing (DSP)-based RF impairment mitigation in real world transceivers. Moreover, the results can be used as a starting point for future research concerning, e.g., joint effects of multiple RF impairments and their mitigation in multiantenna systems. Overall, this thesis and the associated publications can help the communications society to reach the ambitious aim of flexible, low-cost and high performance radio networks in the future

Architectures and Integrated Circuits for Efficient, High-power "Digital'' Transmitters for Millimeter-wave Applications

This thesis presents architectures and integrated circuits for the implementation of energy-efficient, high-power "digital'' transmitters to realize high-speed long-haul links at millimeter-wave frequencies in nano-scale silicon-based processes