Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Design techniques for low-power SAR ADCs in nano-scale CMOS technologies

This thesis presents low power design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nano-scale CMOS technologies. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. To improve the comparator’s power efficiency, a statistical estimation based comparator noise reduction technique is presented. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR) by estimating the conversion residue. A first prototype ADC in 65nm CMOS has been developed to validate the proposed noise reduction technique. It achieves 4.5 fJ/conv-step Walden figure of merit and 64.5 dB signal-to-noise and distortion ratio (SNDR). In addition, a bidirectional single-side switching technique is developed to reduce the DAC switching power. It can reduce the DAC switching power and the total number of unit capacitors by 86% and 75%, respectively. A second prototype ADC with the proposed switching technique is designed and fabricated in 180nm CMOS technology. It achieves an SNDR of 63.4 dB and consumes only 24 Wat 1MS/s, leading to aWalden figure of merit of 19.9 fJ/conv-step. This thesis also presents an improved loop-unrolled SAR ADC, which works at high frequency with reduced SAR logic power and delay. It employs the bidirectional single-side switching technique to reduce the comparator common-mode voltage variation. In addition, it uses a Vcm-adaptive offset calibration technique which can accurately calibrate comparator’s offset at its operating Vcm. A prototype ADC designed in 40nm CMOS achieves 35 dB at 700 MS/s sampling rate and consumes only 0.95 mW, leading to a Walden figure of merit of 30 fJ/conv-step.Electrical and Computer Engineerin

700mV low power low noise implantable neural recording system design

This dissertation presents the work for design and implementation of a low power, low noise neural recording system consisting of Bandpass Amplifier and Pipelined Analog to Digital Converter (ADC) for recording neural signal activities. A low power, low noise two stage neural amplifier for use in an intelligent Radio-Frequency Identification (RFID) based on folded cascode Operational Transconductance Amplifier (OTA) is utilized to amplify the neural signals. The optimization of the number of amplifier stages is discussed to achieve the minimum power and area consumption. The amplifier power supply is 0.7V. The midband gain of amplifier is 58.4dB with a 3dB bandwidth from 0.71 to 8.26 kHz. Measured input-referred noise and total power consumption are 20.7 μVrms and 1.90 μW respectively. The measured result shows that the optimizing the number of stages can achieve lower power consumption and demonstrates the neural amplifier's suitability for instu neutral activity recording. The advantage of power consumption of Pipelined ADC over Successive Approximation Register (SAR) ADC and Delta-Sigma ADC is discussed. An 8 bit fully differential (FD) Pipeline ADC for use in a smart RFID is presented in this dissertation. The Multiplying Digital to Analog Converter (MDAC) utilizes a novel offset cancellation technique robust to device leakage to reduce the input drift voltage. Simulation results of static and dynamic performance show this low power Pipeline ADC is suitable for multi-channel neural recording applications. The performance of all proposed building blocks is verified through test chips fabricated in IBM 180nm CMOS process. Both bench-top and real animal test results demonstrate the system's capability of recording neural signals for neural spike detection

Implementation of Low Power and Area Efficient 2-Bit/Step Asynchronous SAR ADC using Successively Activated Comparators

A low power (0.4-09V) 2-Bit/Step successive approximation register (SAR) analog to digital converter (ADC) is conferred. A 2-Bit/Step operation technique is proposed which implementing a dynamic threshold configuring comparator instead of number of digital to analog converters (DACs). Area and power is reduced by successively activated comparators. Here the second comparator is activated reflecting the preceding comparator’s results. Because the second comparator threshold is configured dynamically for every cycle, only two comparators are required instead of three. By successively activating the comparators, the number of DAC settling is halved, so the power and area overhead is very small and the performance will be increased. The proposed ADC was implemented in a 90nm technology achieved a gain of 35.4 db, power of 0.89 ?w and the conversion time of 0.32ns with a supply voltage of 0.4v. The total core area of this ADC is 7.74 ?m2

A Triple-Mode Performance-Optimized Reconfigurable Incremental ADC for Smart Sensor Applications

This paper proposes a triple-mode discrete-time incremental analog-to-digital converter (IADC) employing successive approximation register (SAR)-based zooming and extended counting (EC) schemes to achieve programmable trade-off capability of resolution and power consumption in various smart sensor applications. It mainly consists of an incremental delta???sigma modulator and the proposed SAR-EC sub-ADC for alternate operation of the coarse SAR conversion and EC. They can be reconfigured to operate separately depending on the application requirements. The SAR-based zooming structure allows the IADC to have better linearity and resolution, and additional activation of the EC function gives the further resolution. During this reconfigurable conversion process, pipelined reusing operation of sub-blocks reduces the silicon area and the number of cycles for target resolutions. A prototype ADC is fabricated in a 180-nm CMOS process, and its triple-mode operation of high-resolution, medium-resolution, and low-power is experimentally verified to achieve 116.1-, 109.4-, and 73.3-dB dynamic ranges, consuming 1.60, 1.26, and 0.39 mW, respectively

A 14-bit 250 MS/s IF Sampling Pipelined ADC in 180 nm CMOS Process

This paper presents a 14-bit 250 MS/s ADC fabricated in a 180 nm CMOS process, which aims at optimizing its linearity, operating speed, and power efficiency. The implemented ADC employs an improved SHA with parasitic optimized bootstrapped switches to achieve high sampling linearity over a wide input frequency range. It also explores a dedicated foreground calibration to correct the capacitor mismatches and the gain error of residue amplifier, where a novel configuration scheme with little cost for analog front-end is developed. Moreover, a partial non-overlapping clock scheme associated with a high-speed reference buffer and fast comparators is proposed to maximize the residue settling time. The implemented ADC is measured under different input frequencies with a sampling rate of 250 MS/s and it consumes 300 mW from a 1.8 V supply. For 30 MHz input, the measured SFDR and SNDR of the ADC is 94.7 dB and 68.5 dB, which can remain over 84.3 dB and 65.4 dB for up to 400 MHz. The measured DNL and INL after calibration are optimized to 0.15 LSB and 1.00 LSB, respectively, while the Walden FOM at Nyquist frequency is 0.57 pJ/step