81 research outputs found

    Localizing noncooperative receiver through full-duplex amplify-and-forward relay

    Get PDF
    Localizing noncooperative transmitter (Tx) and receiver (Rx) that belong to another system is important in many scenarios, e.g., interference management in cognitive radio systems and user behavior learning in ad hoc wireless networks. However, obtaining the locations of these nodes in particular in frequency-division duplex systems is challenging, since the localization network usually does not know the spectrum that the Rx uses for backward transmission. In this paper, we propose to use the full-duplex relay technique to localize a noncooperative Rx, which does not require the knowledge of the Rx’s backward transmission spectrum. In the proposed method, localization sensors alternatively act as a full-duplex amplify-and-forward relay to trigger the power control of the Tx–Rx link. Then, by detecting the power adjustment of the Tx, each localization sensor can estimate the time difference of arrival between the direct and relay signals. Finally, the Rx location can be calculated from triangulation. Simulation results show that the proposed method can effectively localize the Rx, which validates its potential for receiver-aware applications and services

    Energy-Efficient Power Control for Multiple-Relay Cooperative Networks Using Q-Learning

    Get PDF
    In this paper, we investigate the power control problem in a cooperative network with multiple wireless transmitters, multiple amplify-and-forward relays, and one destination. The relay communication can be either full duplex or half-duplex, and all source nodes interfere with each other at every intermediate relay node, and all active nodes (transmitters and relay nodes) interfere with each other at the base station. A game-theory-based power control algorithm is devised to allocate the powers among all active nodes. The source nodes aim at maximizing their energy efficiency (in bits per Joule per Hertz), whereas the relays aim at maximizing the network sum rate. We show that the proposed game admits multiple pure/mixed-strategy Nash equilibrium points. A Q-learning-based algorithm is then formulated to let the active players converge to the best Nash equilibrium point that combines good performance in terms of both energy efficiency and overall data rate. Numerical results show that the full-duplex scheme outperforms half-duplex configuration, Nash bargaining solution, the max-min fairness, and the max-rate optimization schemes in terms of energy efficiency, and outperforms the half-duplex mode, Nash bargaining system, and the max-min fairness scheme in terms of network sum rate

    Relay assisted device-to-device communication with channel uncertainty

    Get PDF
    The gains of direct communication between user equipment in a network may not be fully realised due to the separation between the user equipment and due to the fading that the channel between these user equipment experiences. In order to fully realise the gains that direct (device-to-device) communication promises, idle user equipment can be exploited to serve as relays to enforce device-to-device communication. The availability of potential relay user equipment creates a problem: a way to select the relay user equipment. Moreover, unlike infrastructure relays, user equipment are carried around by people and these users are self-interested. Thus the problem of relay selection goes beyond choosing which device to assist in relayed communication but catering for user self-interest. Another problem in wireless communication is the unavailability of perfect channel state information. This reality creates uncertainty in the channel and so in designing selection algorithms, channel uncertainty awareness needs to be a consideration. Therefore the work in this thesis considers the design of relay user equipment selection algorithms that are not only device centric but that are relay user equipment centric. Furthermore, the designed algorithms are channel uncertainty aware. Firstly, a stable matching based relay user equipment selection algorithm is put forward for underlay device-to-device communication. A channel uncertainty aware approach is proposed to cater to imperfect channel state information at the devices. The algorithm is combined with a rate based mode selection algorithm. Next, to cater to the queue state at the relay user equipment, a cross-layer selection algorithm is proposed for a twoway decode and forward relay set up. The algorithm proposed employs deterministic uncertainty constraint in the interference channel, solving the selection algorithm in a heuristic fashion. Then a cluster head selection algorithm is proposed for device-to-device group communication constrained by channel uncertainty in the interference channel. The formulated rate maximization problem is solved for deterministic and probabilistic constraint scenarios, and the problem extended to a multiple-input single-out scenario for which robust beamforming was designed. Finally, relay utility and social distance based selection algorithms are proposed for full duplex decode and forward device-to-device communication set up. A worst-case approach is proposed for a full channel uncertainty scenario. The results from computer simulations indicate that the proposed algorithms offer spectral efficiency, fairness and energy efficiency gains. The results also showed clearly the deterioration in the performance of networks when perfect channel state information is assumed

    Direct communication radio Iinterface for new radio multicasting and cooperative positioning

    Get PDF
    Cotutela: Universidad de defensa UNIVERSITA’ MEDITERRANEA DI REGGIO CALABRIARecently, the popularity of Millimeter Wave (mmWave) wireless networks has increased due to their capability to cope with the escalation of mobile data demands caused by the unprecedented proliferation of smart devices in the fifth-generation (5G). Extremely high frequency or mmWave band is a fundamental pillar in the provision of the expected gigabit data rates. Hence, according to both academic and industrial communities, mmWave technology, e.g., 5G New Radio (NR) and WiGig (60 GHz), is considered as one of the main components of 5G and beyond networks. Particularly, the 3rd Generation Partnership Project (3GPP) provides for the use of licensed mmWave sub-bands for the 5G mmWave cellular networks, whereas IEEE actively explores the unlicensed band at 60 GHz for the next-generation wireless local area networks. In this regard, mmWave has been envisaged as a new technology layout for real-time heavy-traffic and wearable applications. This very work is devoted to solving the problem of mmWave band communication system while enhancing its advantages through utilizing the direct communication radio interface for NR multicasting, cooperative positioning, and mission-critical applications. The main contributions presented in this work include: (i) a set of mathematical frameworks and simulation tools to characterize multicast traffic delivery in mmWave directional systems; (ii) sidelink relaying concept exploitation to deal with the channel condition deterioration of dynamic multicast systems and to ensure mission-critical and ultra-reliable low-latency communications; (iii) cooperative positioning techniques analysis for enhancing cellular positioning accuracy for 5G+ emerging applications that require not only improved communication characteristics but also precise localization. Our study indicates the need for additional mechanisms/research that can be utilized: (i) to further improve multicasting performance in 5G/6G systems; (ii) to investigate sideline aspects, including, but not limited to, standardization perspective and the next relay selection strategies; and (iii) to design cooperative positioning systems based on Device-to-Device (D2D) technology

    Timing and Carrier Synchronization in Wireless Communication Systems: A Survey and Classification of Research in the Last 5 Years

    Get PDF
    Timing and carrier synchronization is a fundamental requirement for any wireless communication system to work properly. Timing synchronization is the process by which a receiver node determines the correct instants of time at which to sample the incoming signal. Carrier synchronization is the process by which a receiver adapts the frequency and phase of its local carrier oscillator with those of the received signal. In this paper, we survey the literature over the last 5 years (2010–2014) and present a comprehensive literature review and classification of the recent research progress in achieving timing and carrier synchronization in single-input single-output (SISO), multiple-input multiple-output (MIMO), cooperative relaying, and multiuser/multicell interference networks. Considering both single-carrier and multi-carrier communication systems, we survey and categorize the timing and carrier synchronization techniques proposed for the different communication systems focusing on the system model assumptions for synchronization, the synchronization challenges, and the state-of-the-art synchronization solutions and their limitations. Finally, we envision some future research directions

    Multi-user visible light communications: State-of-the-art and future directions

    Get PDF
    Visible light communications (VLC) builds upon the dual use of existing lighting infrastructure for wireless data transmission. VLC has recently gained interest as cost-effective, secure, and energy-efficient wireless access technology particularly for indoor user-dense environments. While initial studies in this area are mainly limited to single-user point-to-point links, more recent efforts have focused on multi-user VLC systems in an effort to transform VLC into a scalable and fully networked wireless technology. In this paper, we provide a comprehensive overview of multi-user VLC systems discussing the recent advances on multi-user precoding, multiple access, resource allocation, and mobility management. We further provide possible directions for future research in this emerging topic.King Fahd University of Petroleum & Minerals, Dhahran, Saudi Arabia ; TÃœBÄ°TAKPublisher versio

    Performance Analysis of Train Communication Systems

    Get PDF
    Trains are considered as a highly efficient transport mode which generate significant challenges in terms of their communication systems. For improved safety, to cope with the expected rapid increase in traffic, and to meet customer demands, an enhanced and reliable communication system is required for high-speed trains (HSRs). Mobile phone and laptop users would like to make use of the non-negligible time that they spend commuting but current HSR communication systems have a foreseeable end to their lifetime and a reliable, efficient, and fast communication replacement system has become essential. Encouraged by the use of existing power line networks for communication purposes, this research investigates the possibility of developing a train communication system based on the use of overhead line equipment (OLE). The ABCD transfer line model is developed to represent the transfer function of the OLE channel and is evaluated using computer simulations. The simulations of the OLE system used are based on orthogonal frequency division multiplexing as the chosen modulation scheme. Within the train, for the provision of broadband services, developing a reliable communication system which is a combination of power line communication and optical wireless communication services using visible light communication (VLC) is considered. Mathematical methods were developed for these networks to assess the overall capacities and outage probabilities of the hybrid systems. Derivation of such analytical expressions offered opportunities to investigate the impact of several system parameters on the performance of the system. To assess the possibility of improving the performance of the proposed integrated systems, their performance in the presence of different relaying protocols has been comprehensively analyzed in terms of capacity and outage probability. This thesis studied the outage probability and energy per bit consumption performance of different relaying protocols over the VLC channel. Accurate analytical expressions for the overall outage probability and energyper-bit consumption of the proposed system configurations, including the single-hop and multi-hop approaches were derived. It was found that the transfer function of the OLE channel can be represented by the two-port network model. It was also revealed that transmission over OLE is negatively affected by the speed of the train, frequency, and length of the OLE link. In train, relay-based communication systems can provide reliable connectivity to the end-user. However, choosing an optimal system configuration can enhance system performance. It was also shown that increasing relay numbers on the network contributes to the total power consumption of the system

    Channel Simulators for MmWave and 5G Applications

    Get PDF
    Along with the tremendous growth of extremely high traffic demand, 5G radio access technology, is becoming the core component to support massive and multifarious connected devices and real-time, and to offer high reliability wireless communications with high data rate. And millimeter-wave (mmWave) range with a huge frequency spectrum from 3 GHz to 300GHz will perfectly meet the multi-gigabit communicative demand. However, mmWave usage also generally brings new challenges, such as coping with high attenuation or path losses. As an effective method to evaluate the performance of the new concept in communication networks, nowadays, several channel models and simulators have been proposed and developped, such as, WINNER, COST-2100, IMT-Advanced, METIS, NYU Wire-less and QuaDRiGa etc. The thesis goals have been to offer an overview of the advantages and disadvantages of various mmWave channel models existing in the literature, based on the published literature, and to compare based on simulations some of the main features of two selected open-source models, namely the WINNER 2 and QuaDRiGa channel models. In the future, more mmWave channel models are planned to be tested and simulated for a better understanding of their suitability for various mmWave applications

    Contextual Beamforming: Exploiting Location and AI for Enhanced Wireless Telecommunication Performance

    Full text link
    The pervasive nature of wireless telecommunication has made it the foundation for mainstream technologies like automation, smart vehicles, virtual reality, and unmanned aerial vehicles. As these technologies experience widespread adoption in our daily lives, ensuring the reliable performance of cellular networks in mobile scenarios has become a paramount challenge. Beamforming, an integral component of modern mobile networks, enables spatial selectivity and improves network quality. However, many beamforming techniques are iterative, introducing unwanted latency to the system. In recent times, there has been a growing interest in leveraging mobile users' location information to expedite beamforming processes. This paper explores the concept of contextual beamforming, discussing its advantages, disadvantages and implications. Notably, the study presents an impressive 53% improvement in signal-to-noise ratio (SNR) by implementing the adaptive beamforming (MRT) algorithm compared to scenarios without beamforming. It further elucidates how MRT contributes to contextual beamforming. The importance of localization in implementing contextual beamforming is also examined. Additionally, the paper delves into the use of artificial intelligence schemes, including machine learning and deep learning, in implementing contextual beamforming techniques that leverage user location information. Based on the comprehensive review, the results suggest that the combination of MRT and Zero forcing (ZF) techniques, alongside deep neural networks (DNN) employing Bayesian Optimization (BO), represents the most promising approach for contextual beamforming. Furthermore, the study discusses the future potential of programmable switches, such as Tofino, in enabling location-aware beamforming
    • …
    corecore