OUTPUT BASED INPUT SHAPING FOR OPTIMAL CONTROL OF SINGLE LINK FLEXIBLE MANIPULATOR

Endpoint residual vibrations and oscillations due to flexible and rigid body motions are big challenges in control of single link flexible manipulators, it makes positioning of payload difficult especially when using various payloads. This paper present output based input shaping with two different control algorithms for optimal control of single link flexible manipulators. Output based filter (OBF) is designed using the signal output of the system and then incorporated with both linear quadratic regulator (LQR) and PID separately for position and residual vibration control. The Robustness of these control algorithms are tested by changing the payloads from 0g to30g, 50g and 70g in each case. Based on MATLAB simulation results and time response analysis, LQR-OBF outperformed the PID-OBF in both tracking and vibration reduction

Mechatronics of systems with undetermined configurations

This work is submitted for the award of a PhD by published works. It deals with some of the efforts of the author over the last ten years in the field of Mechatronics. Mechatronics is a new area invented by the Japanese in the late 1970's, it consists of a synthesis of computers and electronics to improve mechanical systems. To control any mechanical event three fundamental features must be brought together: the sensors used to observe the process, the control software, including the control algorithm used and thirdly the actuator that provides the stimulus to achieve the end result. Simulation, which plays such an important part in the Mechatronics process, is used in both in continuous and discrete forms. The author has spent some considerable time developing skills in all these areas. The author was certainly the first at Middlesex to appreciate the new developments in Mechatronics and their significance for manufacturing. The author was one of the first mechanical engineers to recognise the significance of the new transputer chip. This was applied to the LQG optimal control of a cinefilm copying process. A 300% improvement in operating speed was achieved, together with tension control. To make more efficient use of robots they have to be made both faster and cheaper. The author found extremely low natural frequencies of vibration, ranging from 3 to 25 Hz. This limits the speed of response of existing robots. The vibration data was some of the earliest available in this field, certainly in the UK. Several schemes have been devised to control the flexible robot and maintain the required precision. Actuator technology is one area where mechatronic systems have been the subject of intense development. At Middlesex we have improved on the Aexator pneumatic muscle actuator, enabling it to be used with a precision of about 2 mm. New control challenges have been undertaken now in the field of machine tool chatter and the prevention of slip. A variety of novel and traditional control algorithms have been investigated in order to find out the best approach to solve this problem

Robot Manipulators

Robot manipulators are developing more in the direction of industrial robots than of human workers. Recently, the applications of robot manipulators are spreading their focus, for example Da Vinci as a medical robot, ASIMO as a humanoid robot and so on. There are many research topics within the field of robot manipulators, e.g. motion planning, cooperation with a human, and fusion with external sensors like vision, haptic and force, etc. Moreover, these include both technical problems in the industry and theoretical problems in the academic fields. This book is a collection of papers presenting the latest research issues from around the world

Observer Sliding Mode Control Design for lower Exoskeleton system: Rehabilitation Case

Sliding mode (SM) has been selected as the controlling technique, and the state observer (SO) design is used as a component of active disturbance rejection control (ADRC) to reduce the knee position trajectory for therapeutic purposes. The suggested controller will improve the needed position performances for the Exoskeleton system when compared to the proportional-derivative controller (PD) and SMC as feed-forward in the ADRC approach, as shown theoretically and through computer simulations. Simulink tool is used in this comparison to analyze the nominal case and several disruption cases. The results of mathematical modeling and simulation studies demonstrated that SMC with a disturbance observer strategy performs better than the PD control system and SMC in feed-forward with a greater capacity to reject disturbances and significantly better than these controllers. Performance indices are used for numerical comparison to demonstrate the superiority of these controllers

Evolutionary swarm algorithm for modelling and control of horizontal flexible plate structures

Numerous advantages offered by the horizontal flexible structure have attracted increasing industrial applications in many engineering fields particularly in the airport baggage conveyor system, micro hand surgery and semiconductor manufacturing industry. Nevertheless, the horizontal flexible structure is often subjected to disturbance forces as vibration is easily induced in the system. The vibration reduces the performance of the system, thus leading to the structure failure when excessive stress and noise prevail. Following this, it is crucial to minimize unwanted vibration so that the effectiveness and the lifetime of the structure can be preserved. In this thesis, an intelligent proportional-integral-derivative (PID) controller has been developed for vibration suppression of a horizontal flexible plate structure. Initially, a flexible plate experimental rig was designed and fabricated with all clamped edges boundary conditions at horizontal position. Then, the data acquisition and instrumentation systems were integrated into the experimental rig. Several experimental procedures were conducted to acquire the input-output vibration data of the system. Next, the dynamics of the system was modeled using linear auto regressive with exogenous, which is optimized with three types of evolutionary swarm algorithm, namely, the particle swarm optimization (PSO), artificial bee colony (ABC) and bat algorithm (BAT) model structure. Their effectiveness was then validated using mean squared error, correlation tests and pole zero diagram stability. Results showed that the PSO algorithm has superior performance compared to the other algorithms in modeling the system by achieving lowest mean squared error of 6103947.4 , correlation of up to 95 % confidence level and good stability. Next, five types of PID based controllers were chosen to suppress the unwanted vibration, namely, PID-Ziegler Nichols (ZN), PID-PSO, PID-ABC, Fuzzy-PID and PID-Iterative Learning Algorithm (ILA). The robustness of the controllers was validated by exerting different types of disturbances on the system. Amongst all controllers, the simulation results showed that PID tuned by ABC outperformed other controllers with 47.60 dB of attenuation level at the first mode (the dominant mode) of vibration, which is equivalent to 45.99 % of reduction in vibration amplitude. By implementing the controllers experimentally, the superiority of PID-ABC based controller was further verified by achieving an attenuation of 23.83 dB at the first mode of vibration and 21.62 % of reduction in vibration amplitude. This research proved that the PID controller tuned by ABC is superior compared to other tuning algorithms for vibration suppression of the horizontal flexible plate structure

Magneto-Rheological Actuators for Human-Safe Robots: Modeling, Control, and Implementation

In recent years, research on physical human-robot interaction has received considerable attention. Research on this subject has led to the study of new control and actuation mechanisms for robots in order to achieve intrinsic safety. Naturally, intrinsic safety is only achievable in kinematic structures that exhibit low output impedance. Existing solutions for reducing impedance are commonly obtained at the expense of reduced performance, or significant increase in mechanical complexity. Achieving high performance while guaranteeing safety seems to be a challenging goal that necessitates new actuation technologies in future generations of human-safe robots. In this study, a novel two degrees-of-freedom safe manipulator is presented. The manipulator uses magneto-rheological fluid-based actuators. Magneto-rheological actuators offer low inertia-to-torque and mass-to-torque ratios which support their applications in human-friendly actuation. As a key element in the design of the manipulator, bi-directional actuation is attained by antagonistically coupling MR actuators at the joints. Antagonistically coupled MR actuators at the joints allow using a single motor to drive multiple joints. The motor is located at the base of the manipulator in order to further reduce the overall weight of the robot. Due to the unique characteristic of MR actuators, intrinsically safe actuation is achieved without compromising high quality actuation. Despite these advantages, modeling and control of MR actuators present some challenges. The antagonistic configuration of MR actuators may result in limit cycles in some cases when the actuator operates in the position control loop. To study the possibility of limit cycles, describing function method is employed to obtain the conditions under which limit cycles may occur in the operation of the system. Moreover, a connection between the amplitude and the frequency of the potential limit cycles and the system parameters is established to provide an insight into the design of the actuator as well as the controller. MR actuators require magnetic fields to control their output torques. The application of magnetic field however introduces hysteresis in the behaviors of MR actuators. To this effect, an adaptive model is developed to estimate the hysteretic behavior of the actuator. The effectiveness of the model is evaluated by comparing its results with those obtained using the Preisach model. These results are then extended to an adaptive control scheme in order to compensate for the effect of hysteresis. In both modeling and control, stability of proposed schemes are evaluated using Lyapunov method, and the effectiveness of the proposed methods are validated with experimental results

Model Based Control of Soft Robots: A Survey of the State of the Art and Open Challenges

Continuum soft robots are mechanical systems entirely made of continuously deformable elements. This design solution aims to bring robots closer to invertebrate animals and soft appendices of vertebrate animals (e.g., an elephant's trunk, a monkey's tail). This work aims to introduce the control theorist perspective to this novel development in robotics. We aim to remove the barriers to entry into this field by presenting existing results and future challenges using a unified language and within a coherent framework. Indeed, the main difficulty in entering this field is the wide variability of terminology and scientific backgrounds, making it quite hard to acquire a comprehensive view on the topic. Another limiting factor is that it is not obvious where to draw a clear line between the limitations imposed by the technology not being mature yet and the challenges intrinsic to this class of robots. In this work, we argue that the intrinsic effects are the continuum or multi-body dynamics, the presence of a non-negligible elastic potential field, and the variability in sensing and actuation strategies.Comment: 69 pages, 13 figure

Proceedings of the NASA Conference on Space Telerobotics, volume 3

The theme of the Conference was man-machine collaboration in space. The Conference provided a forum for researchers and engineers to exchange ideas on the research and development required for application of telerobotics technology to the space systems planned for the 1990s and beyond. The Conference: (1) provided a view of current NASA telerobotic research and development; (2) stimulated technical exchange on man-machine systems, manipulator control, machine sensing, machine intelligence, concurrent computation, and system architectures; and (3) identified important unsolved problems of current interest which can be dealt with by future research